Comparison of Hydraulic Loads on I Girder Bridge of Experiment with Those of Three-Dimensional Two-Phase Flow Analysis and Investigation of Three-Dimensional Effects of Surrounding Topography

Four different riser pipe exit configurations were modelled and the flow across them analysed using STAR CCM+ CFD codes. The analysis was limited to exit configurations because of the length to diameter ratio of riser pipes and the limitations of CFD codes available. Two phase flow analysis of the flow through each of the exit configurations was attempted. The various parameters required for detailed study of the flow were computed. The maximum velocity within the pipe in a two phase flow were determined to 3.42 m/s for an 8 (eight) inch riser pipe. After thorough analysis of the two phase flow regime in each of the individual exit configurations, the third and the fourth exit configurations were seen to have flow properties that ensures easy flow within the production system as well as ensure lower computational cost. Convergence (Iterations), total pressure, static pressure, velocity and pressure drop were used as criteria matrix for selecting ideal riser exit geometry, and the third exit geometry was adjudged the ideal exit geometry of all the geometries. The flow in the third riser exit configuration was modelled as a two phase flow. From the results of the two phase flow analysis, it was concluded that the third riser configuration be used in industrial applications to ensure free flow of crude oil and gas from the oil well during oil production.

Download Full-text

A three-dimensional two-phase flow model for a liquid-fed direct methanol fuel cell

Journal of Power Sources ◽

10.1016/j.jpowsour.2006.10.014 ◽

2007 ◽

Vol 163 (2) ◽

pp. 907-915 ◽

Cited By ~ 43

Author(s):

Jiabin Ge ◽

Hongtan Liu

Keyword(s):

Fuel Cell ◽

Direct Methanol Fuel Cell ◽

Flow Model ◽

Two Phase Flow ◽

Three Dimensional ◽

Phase Flow ◽

Two Phase ◽

Direct Methanol ◽

Methanol Fuel Cell

Download Full-text

A Combined Eulerian and Lagrangian Method for Prediction of Evaporating Sprays

Journal of Engineering for Gas Turbines and Power ◽

10.1115/1.1473153 ◽

2002 ◽

Vol 124 (3) ◽

pp. 481-488 ◽

Cited By ~ 15

Author(s):

M. Burger ◽

G. Klose ◽

G. Rottenkolber ◽

R. Schmehl ◽

D. Giebert ◽

...

Keyword(s):

Two Phase Flow ◽

Initial Conditions ◽

Three Dimensional ◽

Lagrangian Method ◽

Phase Flow ◽

Two Phase Flows ◽

Two Phase ◽

Lagrangian Methods ◽

Eulerian Method ◽

Lagrangian Modeling

Polydisperse sprays in complex three-dimensional flow systems are important in many technical applications. Numerical descriptions of sprays are used to achieve a fast and accurate prediction of complex two-phase flows. The Eulerian and Lagrangian methods are two essentially different approaches for the modeling of disperse two-phase flows. Both methods have been implemented into the same computational fluid dynamics package which is based on a three-dimensional body-fitted finite volume method. Considering sprays represented by a small number of droplet starting conditions, the Eulerian method is clearly superior in terms of computational efficiency. However, with respect to complex polydisperse sprays, the Lagrangian technique gives a higher accuracy. In addition, Lagrangian modeling of secondary effects such as spray-wall interaction enhances the physical description of the two-phase flow. Therefore, in the present approach the Eulerian and the Lagrangian methods have been combined in a hybrid method. The Eulerian method is used to determine a preliminary solution of the two-phase flow field. Subsequently, the Lagrangian method is employed to improve the accuracy of the first solution using detailed sets of initial conditions. Consequently, this combined approach improves the overall convergence behavior of the simulation. In the final section, the advantages of each method are discussed when predicting an evaporating spray in an intake manifold of an internal combustion engine.

Download Full-text

Numerical Simulation and Analysis on Spray Drift Movement of Multirotor Plant Protection Unmanned Aerial Vehicle

Energies ◽

10.3390/en11092399 ◽

2018 ◽

Vol 11 (9) ◽

pp. 2399 ◽

Cited By ~ 5

Author(s):

Fengbo Yang ◽

Xinyu Xue ◽

Chen Cai ◽

Zhu Sun ◽

Qingqing Zhou

Keyword(s):

Fluid Dynamics ◽

Computational Fluid Dynamics ◽

Droplet Size ◽

Wind Field ◽

Flow Model ◽

Two Phase Flow ◽

Plant Protection ◽

Three Dimensional ◽

Phase Flow ◽

Two Phase

In recent years, multirotor unmanned aerial vehicles (UAVs) have become more and more important in the field of plant protection in China. Multirotor unmanned plant protection UAVs have been widely used in vast plains, hills, mountains, and other regions, and become an integral part of China’s agricultural mechanization and modernization. The easy takeoff and landing performances of UAVs are urgently required for timely and effective spraying, especially in dispersed plots and hilly mountains. However, the unclearness of wind field distribution leads to more serious droplet drift problems. The drift and distribution of droplets, which depend on airflow distribution characteristics of UAVs and the droplet size of the nozzle, are directly related to the control effect of pesticide and crop growth in different growth periods. This paper proposes an approach to research the influence of the downwash and windward airflow on the motion distribution of droplet group for the SLK-5 six-rotor plant protection UAV. At first, based on the Navier-Stokes (N-S) equation and SST k–ε turbulence model, the three-dimensional wind field numerical model is established for a six-rotor plant protection UAV under 3 kg load condition. Droplet discrete phase is added to N-S equation, the momentum and energy equations are also corrected for continuous phase to establish a two-phase flow model, and a three-dimensional two-phase flow model is finally established for the six-rotor plant protection UAV. By comparing with the experiment, this paper verifies the feasibility and accuracy of a computational fluid dynamics (CFD) method in the calculation of wind field and spraying two-phase flow field. Analyses are carried out through the combination of computational fluid dynamics and radial basis neural network, and this paper, finally, discusses the influence of windward airflow and droplet size on the movement of droplet groups.

Download Full-text

Two-Phase Flow Field Numerical Simulation in Scrubber for Exhaust Gas Desulfurization

Applied Mechanics and Materials ◽

10.4028/www.scientific.net/amm.541-542.1288 ◽

2014 ◽

Vol 541-542 ◽

pp. 1288-1291

Author(s):

Zhi Feng Dong ◽

Quan Jin Kuang ◽

Yong Zheng Gu ◽

Rong Yao ◽

Hong Wei Wang

Keyword(s):

Numerical Simulation ◽

Flow Field ◽

Flue Gas ◽

Two Phase Flow ◽

Three Dimensional ◽

Flue Gas Desulfurization ◽

Parameter Design ◽

Phase Flow ◽

Two Phase ◽

Entrance Angle

Calculation fluid dynamics software Fluent was used to conduct three-dimensional numerical simulation on gas-liquid two-phase flow field in a wet flue gas desulfurization scrubber. The k-ε model and SIMPLE computing were adopted in the analysis. The numerical simulation results show that the different gas entrance angles lead to internal changes of gas-liquid two-phase flow field, which provides references for reasonable parameter design of entrance angle in the scrubber.

Download Full-text