scholarly journals Effects of Alloying Elements on High Temperature Oxidation of 42% Ni Iron-based Alloy

2007 ◽  
Vol 93 (6) ◽  
pp. 409-415 ◽  
Author(s):  
Tadashi INOUE ◽  
Akio KOBAYASHI ◽  
Katsuhisa YAMAUCHI ◽  
Yoshihiro HOSOYA
Keyword(s):  
High Temperature ◽  
High Temperature Oxidation ◽  
Alloying Elements ◽  
Temperature Oxidation ◽  
Iron Based

scholarly journals Determination of Diffusion Coefficients Using Thermogravimetric Measurements during High Temperature Oxidation

2012 ◽  
Vol 323-325 ◽  
pp. 289-294
Author(s):  
Patrice Berthod ◽  
Lionel Aranda
Keyword(s):  
Diffusion Coefficient ◽  
High Temperature ◽  
Diffusion Coefficients ◽  
High Temperature Oxidation ◽  
Concentration Profiles ◽  
Metallic Elements ◽  
Chromium Diffusion ◽  
Temperature Oxidation ◽  
Iron Based

Thermogravimetry measurements associated to concentration profiles allow determining a diffusion coefficient at high temperature of the most oxidable one among the metallic elements belonging to the chemical composition of an alloy. In this work the employed method is described and applied to chromia-forming alloys essentially based on nickel but also to selected cobalt-based and iron-based alloys. More precisely DCrvalues were estimated for chromium diffusing through the carbide-free zones developed during high temperature oxidation. The effects of the base element, of the chromium carbides density and of the dendritic orientations on the chromium diffusion were evidenced.

Wear and high temperature oxidation behaviour of wire arc sprayed iron based coatings

2014 ◽  
Vol 30 (11) ◽  
pp. 784-790 ◽  
Author(s):  
R. Li ◽  
D. Y. He ◽  
Z. Zhou ◽  
Z. J. Wang ◽  
X. Y. Song
Keyword(s):  
High Temperature ◽  
High Temperature Oxidation ◽  
Oxidation Behaviour ◽  
Temperature Oxidation ◽  
Iron Based

High-Temperature Oxidation Behavior of Cu-Si-Y Alloys

2013 ◽  
Vol 32 (4) ◽  
pp. 397-403
Author(s):  
Qun Liu ◽  
Guangyan Fu ◽  
Yong Su ◽  
Zhigang Zhang ◽  
Qi Xiong
Keyword(s):  
Grain Size ◽  
High Temperature ◽  
Oxidation Resistance ◽  
High Temperature Oxidation ◽  
Oxidation Behavior ◽  
Mass Gain ◽  
Alloying Elements ◽  
Experimental Conditions ◽  
Temperature Oxidation ◽  
High Temperature Oxidation Behavior

AbstractThe effect of rare-earth element Y on high-temperature oxidation behavior of Cu-Si alloys at 973 and 1073 K in 0.1 MPa flowing pure O2 has been investigated. Results show at the two temperatures the mass gain of the alloys with different compositions follows the following sequence, Cu-3Si-1.0Y > Cu-3Si-0Y > Cu-3Si-0.5Y alloy. As the Y content increases, the grain size of the alloys decreases, which accelerates the diffusion rate of the alloying elements in the alloys and oxygen under the experimental conditions, increases the ratio of short-path diffusion, and promotes the formation of SiO2 and Y2O3. The three alloys do not form continuous oxide scales of SiO2 or Y2O3, but their rapid formation and dispersed distribution due to the grain-size reduction may also hinder the diffusion of alloying elements and oxygen, which is beneficial to improve the oxidation resistance of the Y-containing alloys. Thereby, the Cu-3Si-0.5Y alloy has good oxidation resistance. The Cu-3Si-1.0Y alloy exhibits largest mass gain among the three alloys, which is due to the fact that in the alloy with higher Y contend and finer grain size, more amount of Y2O3 is more quickly formed, whose mass occupy a more proportion in the whole mass gain of the alloy.

scholarly journals High-Temperature Oxidation Resistance of Alumina-Forming Austenitic Stainless Steels Optimized by Refractory Metal Alloying

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 213
Author(s):  
Shuqi Zhang ◽  
Dandan Dong ◽  
Qing Wang ◽  
Chuang Dong ◽  
Rui Yang
Keyword(s):  
High Temperature ◽  
Oxidation Resistance ◽  
Stainless Steels ◽  
High Temperature Oxidation ◽  
National Laboratory ◽  
Austenitic Stainless Steels ◽  
Alloying Elements ◽  
Temperature Oxidation ◽  
Oak Ridge ◽  
Al2o3 Particles

Alumina-forming austenitic stainless steels are known for their superior high-temperature oxidation resistance. Following our previous work that solved the matching of major alloying elements in their specific 16-atom cluster formula, we here focus on the 800 °C air-oxidation resistance of 0.08 wt. % C alloy series satisfying cluster formula [(Al0.89Si0.05NbxTa0.06−x)-(Fe11.7−yNiyMn0.3)]Cr3.0−z(Mo,W)z, x = 0.03 or 0.06, y = 3.0 or 3.2, z = 0.07 or 0.2, to explore the effect of minor alloying elements Mo, Nb, Ta and W. This cluster formula is established particularly based on alloys which were originally developed by Oak Ridge National Laboratory. All samples are graded as complete oxidation resistance level according to Chinese standard HB 5258-2000, as their oxidation rate and oxidation-peeling mass are generally below 0.1 g/m2 × h and 1.0 g/m2, respectively. In alloys without Ta and W, a Cr2O3-type oxide layer is formed on the surface and Al2O3 particles of sizes up to 4 μm are distributed beneath it. In contrast, in Ta/W-containing alloys, a continuous protective Al2O3 layer is formed beneath the outer Cr2O3 layer, which prevents internal oxidation and provides the lowest weight gain. Instead of internal Al2O3 particles, AlN is formed in Ta/W-containing alloys. The W-containing alloy possesses the thinnest internal nitride zone, indicating the good inhibition effect of W on nitrogen diffusion.

Sign in / Sign up

Export Citation Format

Share Document