Influences of Heating and Coiling Temperatures on Recrystallization during Hot-rolling Process in Ti Added High-purity Ferritic Stainless Steel

High boron alloyed stainless steel(HBASS) with different Ti content were fabricated by vacuum induction furnace and their microstructure and boride phase were analyzed. The boride phase of HBASS do not contain Ti element is mainly (Fe,Cr)2B phase with slender rod-shape. After adding Ti into steel, because Ti and B preferentially combines into TiB2 phase with petals or small block shape which can stop the formation of hard and brittle (Fe,Cr)2B, so the number of (Fe,Cr)2B phase is reduced. And after adding Ti, many crisscross cracks appeared in internal large (Fe,Cr)2B phase, which will be effective to break into small pieces of boride to improve steel plasticity and shielding thermal neutron performance during hot rolling process.

Download Full-text

Effect of Hot Rolling Process on Deep Drawability and Ridging Tendency of Ti Stabilized 17Cr Stainless Steel

Tetsu-to-Hagane ◽

10.2355/tetsutohagane1955.66.6_657 ◽

1980 ◽

Vol 66 (6) ◽

pp. 657-666 ◽

Cited By ~ 3

Author(s):

Yasuhiro NAKAGAWA ◽

Tetsu SAKAMOTO ◽

Isamu YAMAUCHI ◽

Taketomo YAMAZAKI ◽

Manabu UENO

Keyword(s):

Stainless Steel ◽

Hot Rolling ◽

Rolling Process ◽

Deep Drawability ◽

Hot Rolling Process ◽

Effect Of Hot Rolling

Download Full-text

Interface Microstructure and Properties of 304 Austenite Stainless Steel/Low Carbon Steel Clad Plate by Casting and Hot Rolling Process

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.852.178 ◽

2014 ◽

Vol 852 ◽

pp. 178-182

Author(s):

Shuo Li ◽

Di Tang ◽

Hui Bin Wu ◽

Ji Guang Xiong

Keyword(s):

Mechanical Properties ◽

Stainless Steel ◽

Carbon Steel ◽

Hot Rolling ◽

Low Carbon Steel ◽

Rolling Process ◽

Low Carbon ◽

Interface Shear ◽

Austenite Stainless Steel ◽

Hot Rolling Process

The 304 austenite stainless steel and low carbon steel clad plate was fabricated by casting and hot rolling process. The mechanical properties and interface shear strength of clad plates with different thickness after rolling were investigated in detail. The microstructure characteristics of the clad interface were observed by SEM (Scanning Electron Microscope). The phases and chemical composition were analyzed by XRD (X-ray diffraction) and EDS (energy dispersive spectroscopy). Based on the results, the mechanical properties and interface shear strengths meet the requirements of national standards. No visible cracks were observed in the clad interface after bending test. Cr3C2precipitates, Fe3O4oxides and Fe-Cr intermetallic compound were distributed around the interface of clad plate after casting, but a good metallurgical bonding was achieved after hot-rolling.

Download Full-text

Modeling of Microstructural Evolution in the Hot Rolling Process of Fe-16Cr-4Mn-4Ni-0.05C-0.17N Austenitic Stainless Steel

Materials Science Forum ◽

10.4028/www.scientific.net/msf.949.93 ◽

2019 ◽

Vol 949 ◽

pp. 93-100

Author(s):

Murodjon Turdimatov ◽

Alexander Nam ◽

Rudolf Kawalla ◽

Ulrich Prahl

Keyword(s):

Numerical Simulation ◽

Stainless Steel ◽

Austenitic Stainless Steel ◽

Microstructural Evolution ◽

Hot Rolling ◽

Kinetic Equations ◽

Rolling Process ◽

Compression Tests ◽

Hot Rolling Process ◽

Kinetics Of

The understanding of the softening behaviour during the hot rolling process is required to optimize the hot rolling schedule. Therefore, the microstructural evolution in the hot rolling of austenitic stainless steel was simulated. In this work, kinetics of grain growth was investigated by means of compression tests using the Gleeble HDS V40 and described by appropriate kinetic equations based on the obtained experimental results. Moreover, numerical simulation was performed using the Simufact.forming software. The results of the numerical simulation were further validated by experimental data, which were obtained from the labour continuous hot rolling of the austenitic stainless steel.

Download Full-text

Hot Rolling Process Simulation: Application to UIC-60 Rail Rolling

Recent Patents on Mechanical Engineering ◽

10.2174/1874477x11003010065 ◽

2010 ◽

Vol 3 (1) ◽

pp. 65-71

Author(s):

Armindo Guerrero ◽

Javier Belzunce ◽

Covadonga Betegon ◽

Julio Jorge ◽

Francisco J. Vigil

Keyword(s):

Hot Rolling ◽

Process Simulation ◽

Rolling Process ◽

Hot Rolling Process

Download Full-text

3D-FEM Simulation of Hot Rolling Process and Characterization of the Resultant Microstructure of a Light-Weight Mn Steel

Crystals ◽

10.3390/cryst11050569 ◽

2021 ◽

Vol 11 (5) ◽

pp. 569

Author(s):

Ana Claudia González-Castillo ◽

José de Jesús Cruz-Rivera ◽

Mitsuo Osvaldo Ramos-Azpeitia ◽

Pedro Garnica-González ◽

Carlos Gamaliel Garay-Reyes ◽

...

Keyword(s):

Hot Rolling ◽

Thermomechanical Processing ◽

Computational Simulation ◽

Effective Strain ◽

Fem Simulation ◽

Rolling Process ◽

3D Fem ◽

Hot Rolling Process ◽

Mn Steel

Computational simulation has become more important in the design of thermomechanical processing since it allows the optimization of associated parameters such as temperature, stresses, strains and phase transformations. This work presents the results of the three-dimensional Finite Element Method (FEM) simulation of the hot rolling process of a medium Mn steel using DEFORM-3D software. Temperature and effective strain distribution in the surface and center of the sheet were analyzed for different rolling passes; also the change in damage factor was evaluated. According to the hot rolling simulation results, experimental hot rolling parameters were established in order to obtain the desired microstructure avoiding the presence of ferrite precipitation during the process. The microstructural characterization of the hot rolled steel was carried out using optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). It was found that the phases present in the steel after hot rolling are austenite and α′-martensite. Additionally, to understand the mechanical behavior, tensile tests were performed and concluded that this new steel can be catalogued in the third automotive generation.

Download Full-text