scholarly journals Effect of Fiber Orientation Angle on Viscoelastic Properties of CFRP Subjected to Impact Loads.

1993 ◽  
Vol 42 (476) ◽  
pp. 536-541 ◽  
Author(s):  
Yuji SOGABE ◽  
Masayuki TSUZUKI ◽  
Keizo KISHIDA
Keyword(s):  
Fiber Orientation ◽  
Viscoelastic Properties ◽  
Orientation Angle ◽  
Impact Loads ◽  
Fiber Orientation Angle

Minimize the Deflection of Laminated Composite Plates under the External Load Using Fiber Orientation Angle

2014 ◽  
Vol 709 ◽  
pp. 144-147
Author(s):  
Ying Tao Chen ◽  
Song Xiang ◽  
Wei Ping Zhao
Keyword(s):  
Fiber Orientation ◽  
External Load ◽  
Optimization Problem ◽  
Orientation Angle ◽  
Laminated Composite ◽  
Composite Plates ◽  
Laminated Composite Plates ◽  
Load Optimization ◽  
Fiber Orientation Angle ◽  
Optimization Parameters

Optimization of fiber orientation angle is studied to minimize the deflection of the laminated composite plates by the genetic algorithm. The objective function of optimization problem is the minimum deflection of laminated composite plates under the external load; optimization parameters are fiber orientation angle of laminated composite plates. The results for the optimal fiber orientation angle and the minimum deflection of the 4-layer plates are presented to demonstrate the validity of present method.

scholarly journals Optimization of Laminated Composite Plates for Maximum Biaxial Buckling Load

2020 ◽  
Vol 36 (2) ◽  
Author(s):  
Pham Dinh Nguyen ◽  
Quang-Viet Vu ◽  
George Papazafeiropoulos ◽  
Hoang Thi Thiem ◽  
Pham Minh Vuong ◽  
...  
Keyword(s):  
Fiber Orientation ◽  
Orientation Angle ◽  
Laminated Composite ◽  
Optimization Procedure ◽  
Composite Plates ◽  
Buckling Load ◽  
Biaxial Compression ◽  
Laminated Composite Plates ◽  
Design Variables ◽  
Fiber Orientation Angle

This paper proposes an optimization procedure for maximization of the biaxial buckling load of laminated composite plates using the gradient-based interior-point optimization algorithm. The fiber orientation angle and the thickness of each lamina are considered as continuous design variables of the problem. The effect of the number of layers, fiber orientation angles, thickness and length to thickness ratios on the buckling load of the laminated composite plates under biaxial compression is investigated. The effectiveness of the optimization procedure in this study is compared with previous works.

Accuracy of Intersection Counting Method in Measurement of Fiber Orientation Angle Distribution Using Image Processing

2006 ◽  
Vol 324-325 ◽  
pp. 415-418
Author(s):  
Jin Woo Kim ◽  
Dong Gi Lee
Keyword(s):  
Image Processing ◽  
Fiber Orientation ◽  
Orientation Angle ◽  
Angle Distribution ◽  
Counting Method ◽  
Fiber Aspect Ratio ◽  
Reinforced Composite ◽  
Orientation Function ◽  
Orientation State ◽  
Fiber Orientation Angle

While mold fiber reinforced composite material to problem of occasion that high temperature compression molding, flow length in mold is overlong or when flow meets with resistance in side of mold, fiber orientation happens and big change occurs in strength or quality. Thus, in compression molding that use fiber reinforced composite material, orientation state of fiber in moldings is the most basic element that quotes various properties of matter values. Therefore, to clear orientation state of fiber establishing measurement of fiber orientation angle distribution is very important while give correction of molding condition decision, mechanical quality of moldings and guide about material design. In the study, the fiber orientation distribution of simulation figure plotted by PC is measured using image processing in order to examine the accuracy of intersection counting method. The fiber orientation function measured by intersection counting method using image processing is compared with the calculated fiber orientation function. The results show that the measured value of fiber orientation function using intersection counting method is lower than the calculated value, because the number of intersection between the scanning line and the fiber with smaller fiber aspect ratio is counted less than with larger fiber aspect ratio.

Numerical Simulation of the Orthogonal Cutting of Carbon Fiber Reinforced Composite Material

2014 ◽  
Vol 887-888 ◽  
pp. 1246-1250 ◽  
Author(s):  
Zhi Kai Li ◽  
Dong Lu ◽  
Qiang Wang ◽  
Yong Bo Wu
Keyword(s):  
Carbon Fiber ◽  
Fiber Orientation ◽  
Orthogonal Cutting ◽  
Orientation Angle ◽  
Surface Damage ◽  
Fiber Reinforced ◽  
Fiber Reinforced Composite ◽  
Reinforced Composite ◽  
Fiber Orientation Angle ◽  
Carbon Fiber Reinforced

This work is focused on the study of orthogonal cutting of carbon fiber reinforced composite. A model based on finite element was developed. Through defining ultimate stresses of fiber tension cracking and fiber compression bucking, ultimate stresses of matrix longitudinal tensile and shear damage. Cutting forces obtained from the FE simulation matches well with the experimental observations. Than analysis cracking and crushing phenomenon of matrix in different fiber orientation, the influence of fiber orientation on sub-surface damage was studied, it shows that the cracking of sub-surface damage value increased with the increase of fiber orientation angle.

The effects of cutouts on buckling behavior of composite plates

2012 ◽  
Vol 19 (3) ◽  
pp. 323-330 ◽  
Author(s):  
Ahmet Erkliğ ◽  
Eyüp Yeter
Keyword(s):  
Fiber Orientation ◽  
Polymer Matrix Composites ◽  
Orientation Angle ◽  
Composite Plates ◽  
Buckling Load ◽  
Matrix Composites ◽  
Element Analysis ◽  
Buckling Loads ◽  
Buckling Behavior ◽  
Fiber Orientation Angle

AbstractCutouts such as circular, rectangular, square, elliptical, and triangular shapes are generally used in composite plates as access ports for mechanical and electrical systems, for damage inspection, to serve as doors and windows, and sometimes to reduce the overall weight of the structure. This paper addresses the effects of different cutouts on the buckling behavior of plates made of polymer matrix composites. To study the effects of cutouts on buckling, loaded edges are taken as fixed and unloaded edges are taken as free. Finite element analysis is also performed to predict the effects of different geometrical cutouts, orientations, and position of cutouts on the buckling behavior. The results show that fiber orientation angle and cutout sizes are the most important parameters on the buckling loads. For all types of cutouts the buckling loads decrease dramatically by increasing the fiber orientation angle. It is observed that minimum buckling load is reached when 45° fiber angle is used, and after this angle critical buckling load begins to increase. Also, it is concluded that while fiber orientation angle is 0°, elliptical cutout has the highest buckling load and while fiber orientation angle is 45°, circular cutout has the highest buckling load.

Optimum fiber orientation angle of multiaxially laminated compositesbased on reliability

AIAA Journal ◽  
1993 ◽  
Vol 31 (5) ◽  
pp. 919-920 ◽  
Author(s):  
Shaowen Shao ◽  
Mitsunori Miki ◽  
Yoshisada Murotsu
Keyword(s):  
Fiber Orientation ◽  
Orientation Angle ◽  
Fiber Orientation Angle

scholarly journals Effect of fiber orientation on viscoelastic properties of CFRP subjected to impact loads.

1989 ◽  
Vol 38 (432) ◽  
pp. 1001-1006
Author(s):  
Yuji SOGABE ◽  
Masayuki TSUZUKI ◽  
Keizo KISHIDA
Keyword(s):  
Fiber Orientation ◽  
Viscoelastic Properties ◽  
Impact Loads
Sign in / Sign up

Export Citation Format

Share Document