scholarly journals Influence of water absorption on the fiber/matrix interfacial shear strength of glass fiber reinforced degradation controlled PLA model composite

2016 ◽  
Author(s):  
K. Tanaka ◽  
A. Inagaki ◽  
M. Miyamura ◽  
T. Katayama ◽  
S. Yoshikawa ◽  
...  
Keyword(s):  
Shear Strength ◽  
Water Absorption ◽  
Glass Fiber ◽  
Interfacial Shear Strength ◽  
Interfacial Shear ◽  
Fiber Reinforced ◽  
Model Composite ◽  
Glass Fiber Reinforced ◽  
Influence Of Water ◽  
Fiber Matrix

scholarly journals Effects of Water Absorption on the Fiber–Matrix Interfacial Shear Strength of Carbon Nanotube-Grafted Carbon Fiber Reinforced Polyamide Resin

2019 ◽  
Vol 3 (1) ◽  
pp. 4 ◽  
Author(s):  
Kazuto Tanaka ◽  
Saya Okuda ◽  
Yoshitaka Hinoue ◽  
Tsutao Katayama
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Carbon Fiber ◽  
Water Absorption ◽  
Interfacial Shear Strength ◽  
Interfacial Shear ◽  
Fiber Reinforced ◽  
Pull Out ◽  
Fiber Matrix ◽  
Carbon Fiber Reinforced

Carbon fiber reinforced thermoplastics (CFRTPs) are expected to be used for the structural parts of automobiles and aircraft due to their mechanical properties, such as high specific stiffness, high specific strength, short molding times and high recyclability. The fiber/matrix interface of the composite plays an important role in transmitting stress from the matrix to the reinforcing fibers. It was reported that grafting of carbon nanotubes (CNTs) on the carbon fiber can improve the fiber/matrix interfacial property. We have reported that CNTs, which are directly grafted onto carbon fiber using Ni as the catalyst by the chemical vapor deposition (CVD) method, can improve the fiber/matrix interfacial shear strength (IFSS) of carbon fiber/polyamide 6 (PA6). For practical use of CFRTPs, it is important to clarify the effects of water absorption on the mechanical properties of the composite material. In this study, the effects of water absorption on the fiber–matrix interfacial shear strength (IFSS) of carbon fiber reinforced polyamide resin and CNT-grafted carbon fiber reinforced polyamide resin were clarified by the single fiber pull-out test for specimens preserved in air, then in water for 24 h and re-dried after water absorption. The IFSS of carbon fiber/PA6 was significantly decreased by water absorption. In contrast, CNT-grafted carbon fiber/PA6 showed smaller degradation of the IFSS by water absorption.

scholarly journals Enhanced Interfacial Shear Strength and Critical Energy Release Rate in Single Glass Fiber-Crosslinked Polypropylene Model Microcomposites

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2552 ◽  
Author(s):  
Uwe Gohs ◽  
Michael Mueller ◽  
Carsten Zschech ◽  
Serge Zhandarov
Keyword(s):  
Shear Strength ◽  
Electron Beam ◽  
Energy Release Rate ◽  
Glass Fiber ◽  
Release Rate ◽  
Interfacial Shear Strength ◽  
Glass Fibers ◽  
Critical Energy ◽  
Interfacial Shear ◽  
Critical Energy Release Rate

Continuous glass fiber-reinforced polypropylene composites produced by using hybrid yarns show reduced fiber-to-matrix adhesion in comparison to their thermosetting counterparts. Their consolidation involves no curing, and the chemical reactions are limited to the glass fiber surface, the silane coupling agent, and the maleic anhydride-grafted polypropylene. This paper investigates the impact of electron beam crosslinkable toughened polypropylene, alkylene-functionalized single glass fibers, and electron-induced grafting and crosslinking on the local interfacial shear strength and critical energy release rate in single glass fiber polypropylene model microcomposites. A systematic comparison of non-, amino-, alkyl-, and alkylene-functionalized single fibers in virgin, crosslinkable toughened and electron beam crosslinked toughened polypropylene was done in order to study their influence on the local interfacial strength parameters. In comparison to amino-functionalized single glass fibers in polypropylene/maleic anhydride-grafted polypropylene, an enhanced local interfacial shear strength (+20%) and critical energy release rate (+80%) were observed for alkylene-functionalized single glass fibers in electron beam crosslinked toughened polypropylene.

Sign in / Sign up

Export Citation Format

Share Document