Interaction of Longitudinal Vortex with Horseshoe Vortex Configuration Effect of Longitudinal Vortex

Author(s):  
Masaharu Andoh ◽  
Masahiro Motosuke ◽  
Shinji Honami
Author(s):  
Shinji Honami ◽  
Masaharu Andoh ◽  
Satoshi Tanabe ◽  
Masahiro Motosuke

Manipulation of the horseshoe vortex is a key technology for improvement of blade performance in the turbine blade passage, since the complicated interaction process of the vortices occurs around the blade. The target of the present study is to clarify the interaction process between the leg vortex of the horseshoe vortex produced by the blade and the longitudinal vortex produced by the vortex generator. The arrangement of the vortex generator wings which correspond to Common Flow Down configuration is discussed. The effect of the spacing of the longitudinal vortices is also tested. The narrow and wide spacing results in the different longitudinal vortex location at the top or side of the horseshoe vortex. The measurement by the hot wire anemometer which has an X-type rotating prong by a stepping motor provides three components of the velocity and the detailed turbulence kinetic energy and the Reynolds stress profiles giving the clear understanding of the complicated interaction process of the two vortices. The narrow spacing of the longitudinal vortex in Common Flow Down configuration shows the strong interaction of the horseshoe vortex and longitudinal vortex dynamics.


Author(s):  
Masaharu Andoh ◽  
Masahiro Motosuke ◽  
Shinji Honami

A horseshoe vortex at the blade-endwall junction introduces the reduction of turbine blade performance due to the three dimensional separation near the stagnation point of the blade and the interaction of the two legs of the horseshoe vortex in the turbine cascade passage. In order to simulate the interaction of the leg vortices in the passage, a pair of vortex generators which produces the longitudinal vortices from the tip of the generator wings is installed upstream of the blade. The experiments are made under the different configuration of the longitudinal vortex generators. NACA 0024 airfoil at zero angle of attack is used as the blade in the wind tunnel where the undisturbed momentum thickness Reynolds number is 1700. The detailed measurements on the three-components of time-averaged and fluctuated velocities are conducted by a small size of rotating X-probe hot-wire anemometer with a miniature stepping motor at the prong. The location of the leg of the horseshoe vortex can be controlled by changing the spacing of the longitudinal vortex generators. The strong dependence of the spacing of the longitudinal vortex generators on the profiles of Reynolds stress and the temporal velocity is clarified.


2021 ◽  
Vol 3 (8) ◽  
Author(s):  
Felipe A. S. Silva ◽  
Luis Júnior ◽  
José Silva ◽  
Sandilya Kambampati ◽  
Leandro Salviano

AbstractSolar Water Heater (SWH) has low efficiency and the performance of this type of device needs to be improved to provide useful and ecological sources of energy. The passive techniques of augmentation heat transfer are an effective strategy to increase the convective heat transfer coefficient without external equipment. In this way, recent investigations have been done to study the potential applications of different inserts including wire coils, vortex generators, and twisted tapes for several solar thermal applications. However, few researchers have investigated inserts in SWH which is useful in many sectors where the working fluid operates at moderate temperatures. The longitudinal vortex generators (LVG) have been applied to promote heat transfer enhancement with a low/moderate pressure drop penalty. Therefore, the present work investigated optimal geometric parameters of LVG to enhance the heat transfer for a SWH at low Reynolds number and laminar flow, using a 3D periodical numerical simulation based on the Finite Volume Method coupled to the Genetic Algorithm optimization method (NSGA-II). The LVG was stamped over a flat plate inserted inside a smooth tube operating under a typical residential application corresponding to Reynolds numbers of 300, 600, and 900. The geometric parameters of LGV were submitted to the optimization procedure which can find traditional LVG such as rectangular-winglet and delta-winglet or a mix of them. The results showed that the application of LGVs to enhance heat transfer is an effective passive technique. The different optimal shapes of the LVG for all Reynolds numbers evaluated improved more than 50% of heat transfer. The highest augmentation heat transfer of 62% is found for the Reynolds number 900. However, the best thermo-hydraulic efficiency value is found for the Reynolds number of 600 in which the heat transfer intensification represents 55% of the pressure drop penalty.


Sign in / Sign up

Export Citation Format

Share Document