scholarly journals OPTIMIZATION OF ALGORITHMS FOR OBTAINING RESONANCE FREQUENCY HETEROAUXIN PREPARATIONS FOR VEGETATIVE PROPAGATION OF GRAPES

2021 ◽  
Vol 6 (72) ◽  
pp. 103-113
Author(s):  
Egor Anatolievich Olkhovatov ◽  
◽  
Pyotr Panteleevich Radchevsky ◽  
Angelina Anatolievna Chizheumova ◽  
◽  
...  
Keyword(s):  
Resonance Frequency ◽  
Vegetative Propagation

Actuation and dynamic mechanical characteristics of a core free flat dielectric electro-active polymer soft actuator

2020 ◽  
Vol 14 (4) ◽  
pp. 7396-7404
Author(s):  
Abdul Malek Abdul Wahab ◽  
Emiliano Rustighi ◽  
Zainudin A.
Keyword(s):  
Theoretical Model ◽  
Resonance Frequency ◽  
Dynamic Testing ◽  
Experimental Results ◽  
Percentage Error ◽  
Initial Tension ◽  
Average Percentage ◽  
Soft Actuator ◽  
Average Percentage Error ◽  
Mechanical Dynamics

Various complex shapes of dielectric electro-active polymer (DEAP) actuator have been promoted for several types of applications. In this study, the actuation and mechanical dynamics characteristics of a new core free flat DEAP soft actuator were investigated. This actuator was developed by Danfoss PolyPower. DC voltage of up to 2000 V was supplied for identifying the actuation characteristics of the actuator and compare with the existing formula. The operational frequency of the actuator was determined by dynamic testing. Then, the soft actuator has been modelled as a uniform bar rigidly fixed at one end and attached to mass at another end. Results from the theoretical model were compared with the experimental results. It was found that the deformation of the current actuator was quadratic proportional to the voltage supplied. It was found that experimental results and theory were not in good agreement for low and high voltage with average percentage error are 104% and 20.7%, respectively. The resonance frequency of the actuator was near 14 Hz. Mass of load added, inhomogeneity and initial tension significantly affected the resonance frequency of the soft actuator. The experimental results were consistent with the theoretical model at zero load. However, due to inhomogeneity, the frequency response function’s plot underlines a poor prediction where the theoretical calculation was far from experimental results as values of load increasing with the average percentage error 15.7%. Hence, it shows the proposed analytical procedure not suitable to provide accurate natural frequency for the DEAP soft actuator.

Influence of Bone Quality, Drilling Protocol, Implant Diameter/Length on Primary Stability: An In Vitro Comparative Study on Insertion Torque and Resonance Frequency Analysis

2020 ◽  
Vol 46 (3) ◽  
pp. 182-189 ◽  
Author(s):  
Davide Farronato ◽  
Mattia Manfredini ◽  
Michele Stocchero ◽  
Mattia Caccia ◽  
Lorenzo Azzi ◽  
...  
Keyword(s):  
Resonance Frequency ◽  
Bone Quality ◽  
Frequency Analysis ◽  
Primary Stability ◽  
Mean Difference ◽  
Insertion Torque ◽  
Resonance Frequency Analysis ◽  
Bone Response ◽  
Implant Length

The aim of this study was to evaluate the influence of bone quality, drilling technique, implant diameter, and implant length on insertion torque (IT) and resonance frequency analysis (RFA) of a prototype-tapered implant with knife-edge threads. The investigators hypothesized that IT would be affected by variations in bone quality and drilling protocol, whereas RFA would be less influenced by such variables. The investigators implemented an in vitro experiment in which a prototype implant was inserted with different testing conditions into rigid polyurethane foam blocks. The independent variables were: bone quality, drilling protocol, implant diameter, and implant length. Group A implants were inserted with a conventional drilling protocol, whereas Group B implants were inserted with an undersized drilling protocol. Values of IT and RFA were measured at implant installation. IT and RFA values were significantly correlated (Pearson correlation coefficient: 0.54). A multivariable analysis showed a strong model. Higher IT values were associated with drilling protocol B vs A (mean difference: 71.7 Ncm), implant length (3.6 Ncm increase per mm in length), and substrate density (0.199 Ncm increase per mg/cm3 in density). Higher RFA values were associated with drilling protocol B vs A (mean difference: 3.9), implant length (1.0 increase per mm in length), and substrate density (0.032 increase per mg/cm3 in density). Implant diameter was not associated with RFA or IT. Within the limitations of an in vitro study, the results of this study suggest that the studied implant can achieve good level of primary stability in terms of IT and RFA. A strong correlation was found between values of IT and RFA. Both parameters are influenced by the drilling protocol, implant length, and substrate density. Further studies are required to investigate the clinical response in primary stability and marginal bone response.

PECULIARITIES OF THE RESONANCE FREQUENCY MECHANICAL TUNING OF THE WAVEGUIDE-DIELECTRIC RESONATOR

2013 ◽  
Vol 72 (19) ◽  
pp. 1739-1746
Author(s):  
R. I. Belous ◽  
S. P. Martynyuk ◽  
A. P. Motornenko ◽  
I. G. Skuratovskiy ◽  
O. I. Khazov
Keyword(s):  
Resonance Frequency ◽  
Dielectric Resonator ◽  
Mechanical Tuning

COMPOUND FAULT DIAGNOSIS OF BEARINGS USING AN IMPROVED SPECTRAL KURTOSIS BY MAXIMUM CORRELATION KURTOSIS DECONVOLUTION (MCKD).

2020 ◽  
Vol 9 (8) ◽  
pp. 66-72
Keyword(s):  
Fault Diagnosis ◽  
Resonance Frequency ◽  
Background Noise ◽  
Maximum Correlation ◽  
Vibration Signals ◽  
Filter Length ◽  
Frequency Bands ◽  
Noise Interference ◽  
Spectral Kurtosis

This paper discusses the use of Maximum Correlation kurtosis deconvolution (MCKD) method as a pre-processor in fast spectral kurtosis (FSK) method in order to find the compound fault characteristics of the bearing, by enhancing the vibration signals. FSK only extracts the resonance bands which have maximum kurtosis value, but sometimes it might possible that faults occur in the resonance bands which has low kurtosis value, also the faulty signals missed due to noise interference. In order to overcome these limitations FSK used with MCKD, MCKD extracts various faults present in different resonance frequency bands; also detect the weak impact component, as MCKD also dealt with strong background noise. By obtaining the MCKD parameters like, filter length & deconvolution period, we can extract the compound fault feature characteristics.

Sign in / Sign up

Export Citation Format

Share Document