Effects of Implanting Torques on Implant Osseointegration in an Animal Model

Objective: To investigate the effect of insertion torque on implant osseointegration in an animal model. Methods: First, the first to fourth premolars of nine healthy adult beagles’ mandibular were extracted to form an edentulous area, and then the beagles were equally divided into three groups with different torques (low torque: 10–30 Ncm; medium torque: 30–50 Ncm; high torque: > 70 Ncm). Three implants were placed on each side of the edentulous area of the beagles (54 total), and the dogs were observed for 8 weeks. Implant performance and removal torque values (RTV) were determined at 1, 4, and 8 weeks after surgery. In addition, the expression ratios of OPG and RANKL mRNAs in the surrounding bone tissue were determined. Results: None of the 54 implants showed loosening or loss, and no significant bone resorption was observed. The removing torques and the expression ratios of OPG and RANKL mRNAs showed differences at 1 and 4 weeks after surgery, while they converged at 8 weeks after the surgery (p > 0.05). Conclusion: The osteointegration process lasted approximately 8 weeks depending on the difference in parameters, and all parameters showed the same values even though the insertion torques at the beginning were different.

Effects of insertion torque values on the marginal bone loss of dental implants installed in sheep mandibles

The aim of the present in vivo study was to analyze and compare the effects on the crestal bone healing of two different implant macrogeometries installed in fresh socket areas and in normal bone areas with different insertion torque values. Two implant macrogeometries were used in the present study, DuoCone implant (DC) and Maestro implant (MAE), forming four groups: group DCws, in which the implants were installed in healing bone (without a socket); group DCfs, in which the implants were installed in post-extraction areas (fresh sockets); group MAEws, in which the implants were installed in healing bone (without a socket); group MAEfs, in which the implants were installed in post-extraction areas (fresh sockets). After 30 and 90 days of implantations in the bilateral mandibles of 10 sheep, eighty implants were evaluated through digital X-ray images and histologic slices. The crestal bone position in relation to the implant platform shoulder was measured and compared. The measured insertion torque was 47.2 ± 4.69 Ncm for the DCws group, 43.4 ± 4.87 Ncm for the DCfs group, 29.3 ± 3.16 Ncm for the MAEws group, and 27.7 ± 4.41 Ncm for the MAEfs group. The radiographic mesio-distal and histological bucco-lingual analyses showed significantly greater vertical bone loss in the implants installed with high torque (DC groups) in comparison to the implants installed with a low torque (MAE groups) (p < 0.05), at both evaluation times. In general, low insertion torque values (Maestro implants) showed better results of MBL when compared to implants installed with higher torque values (Duo Cone implants). Moreover, our results showed that the implants installed in the sites without sockets showed a less MBL in comparison with the implants installed in sites of fresh sockets.

Five-Year Prospective Study on Implant Failure and Marginal Bone Remodeling Expected Using Bone Level Implants with Sandblasted/Acid-Etched Surface and Conical Connection

Objective The purpose of the present prospective, case-series study was to report implant survival rate and marginal bone remodeling expected 5 years after loading using dental implants placed in daily practice. Materials and Methods This research was designed as an open-cohort, prospective, case-series evaluation. Any partially or completely edentulous patient, scheduled to receive at least one bone level implant, was considered eligible for this study. Primary outcome measurements were: implant and prosthetic cumulative survival rate and any complications experienced up to the 5-year follow-up. Secondary outcome measures were: thickness of gingival biotype, implant insertion torque, implant stability quotient, and marginal bone loss (MBL). Results Ninety consecutive patients (34 males and 56 females, aged between 24 and 81 years old [mean: 53.2 ± 15.4]) with 243 inserted implants were followed for at least 5 years after loading (mean: 65.4 ± 3.1 months; range from 60 to 72). At the 1-year follow-up, no drop-outs were recorded, but 17 patients (18.9%) with 18 restorations (12.6%) delivered on 34 implants (14%) were lost at the 5-year examination. At the 5-year follow-up examination, six implants lost osseointegration (97.5%). In the same period, four prostheses failed (97.2%). Five complications were reported in five different patients (prosthetic success rate was 96.5%, at patient level). Five years after loading, the mean MBL was 0.41 ± 0.30 mm. The difference from the 1-year data was 0.04 ± 0.19 mm. A statistically significant higher MBL was found for smokers, and patients with thin gingival biotype. The mean implant insertion torque was 42.9 ± 4.8 Ncm (range from 15 to 45 Ncm). Two-hundred and three implants (83.5%) were inserted with an insertion torque ≥35 and ≤45 Ncm. Conclusions High implant survival and success rate could be expected with stable marginal bone remodeling up to 5 years after loading. Smoking and thin tissue biotype were the most important variabilities associated with higher MBL. Further research studies are needed to confirm these results.

Bone Damage during Dental Implant Insertion: A Pilot Study Combining Strain Gauge and Histologic Analysis

Besides alveolar bone quality, the drilling protocol applied in conjunction with the design of an implant are the major determinants of primary implant stability. Surgical trauma and bone compression resulting from implant insertion may constitute one cause for marginal bone resorption. Inserting two current bone-level implant designs (Astra; Straumann; n = 5) in bovine ribs, primary stability, strain development on the buccal bone plate and histologic signs of bone damage were recorded. Besides comparing the implant designs (Welch t-tests), all measurement parameters were checked for potential correlations (Pearson product moment correlation coefficients) with the level of significance set at α = 0.05. Considerable numbers of crack formation and plastic deformation of bone were observed after implant insertion. Straumann implants showed slightly greater values for insertion torque (p = 0.772), strain development (p = 0.893) and implant stability (p = 0.642). Significantly greater bone to implant contact (cortical p = 0.014; trabecular p = 0.016) was observed in Straumann implants, while Astra implants caused a significantly greater number of microcracks in cortical bone (p = 0.020). In Straumann implants, insertion torque correlated with bone to implant contact in the cortical area (p = 0.029) and the number of macrocracks in trabecular bone correlated with bone to implant contact (p = 0.029). In Astra implants, insertion torque and bone to implant contact in the trabecular area correlated (p = 0.007) as well as the number of macrocracks in trabecular bone and implant stability (p = 0.016). Additionally, in the area of cortical bone, the number of macrocracks correlated with bone to implant contact (p = 0.019). Implant placement results in bone damage of varying magnitude, which is governed by the drill protocol, implant macrodesign and bone quality.

Immediate Vs. Early Loading of Bone Level Tapered Dental Implants with Hydrophilic Surface in Fully Edentulous Maxilla:Clinical and Patient-Centered Outcomes

ABSTRACT The aim was to: (i) compare changes among primary and secondary implant stability between immediate and early loaded implants in edentulous maxilla, (ii) evaluate oral health related quality of life (OHRQoL) and (iii) determine patient satisfaction with 6-implant supported fixed full-arch dentures. A prospective, randomized controlled clinical trial was conducted on 24 edentulous maxilla patients. The BLT SLActive® implants in 12 patients were immediately loaded with temporary restorations while12 patients did not receive temporary restorations. Definitive (final) dentures were delivered to all patients after 6 weeks. Stability of the implants were assessed by Insertion Torque (IT) and Resonance Frequency Analysis (RFA). Oral Health Impact Profile-19 ( OHIP-19) questionnaire was used to evaluate OHRQoL and a Visual Analogue Scale (VAS) for patient satisfaction. The IT value of implants assigned for immediate and early loading group was 27.17±9.55Ncm and 25.01±11.06Ncm, respectively. Changes in implant stability from baseline to week 6 were similar in both groups when measured by Penguin ® (p=0.881) and Ostell ® (p= 0.828). Patients in the immediate load group reported significantly lower OHIP physical pain scores (p=0.016), OHIP psychological disability score (p=0.046) and significantly higher VAS function score (p=0.009) and VAS aesthetics score (p=0.009). Implant loading protocols don’t have a significant effect on the change in implant stability 6 weeks after implantation, however, immediate loading significantly improves OHRQoL and satisfaction of patients with maxillary edentulism treated by fixed full-arch dentures. Future trials will determine the role of immediate loading protocol in clinical scenarios with various amounts of available jaw bone using different numbers of implants to retain a fixed prosthetic restoration in the edentulous maxilla.

Zirconia vs. Titanium Dental Implants: Primary Stability In-Vitro Analysis

The present experimental trial uses two types of dental implants, one made of titanium (Ti6Al4V) and the other one of zirconia (ZrO2), but both of identical design, to compare their stability and micro-movements values under load. One of each type of implant (n = 42) was placed into 21 cow ribs, recording the insertion torque and the resonance frequency using a specific transducer. Subsequently, a prosthetic crown made of PMMA was screwed onto each of the implants in the sample. They were then subjected to a static compression load on the vestibular cusp of the crown. The resulting micromovements were measured. The zirconia implants obtained a higher mean of both IT and RFA when compared with those of titanium, with statistically significant differences in both cases (p = 0.0483 and p = 0.0296). However, the micromovement values when load was applied were very similar for both types, with the differences between them (p = 0.3867) not found to be statistically significant. The results show that zirconia implants have higher implant stability values than titanium implants. However, the fact that there are no differences in micromobility values implies that caution should be exercised when applying clinical protocols for zirconia based on RFA, which only has evidence for titanium.

Effect of Hafnium Coating on Osseointegration of Titanium Implants: A Split Mouth Animal Study

The behaviour of hafnium as surface coating in biological environments has not been studied. Little is known about osseointegration of hafnium-coated titanium implants. Thus, further studies of hafnium coating under biological conditions are required in order to determine the suitability of this material, as a surface coating for biomedical application. The aim of the study is to analyse the difference between hafnium-coated titanium and uncoated titanium by evaluating the osseointegration ability of hafnium metal and mechanism of which promotes better bone integration. The study was conducted with a split mouth design on 16 Wistar Albino rats of both sexes, at the age of 6-7 months, weighing 2526.5 ± 74.4 g . Self-tapping titanium osteosynthesis screws ( 4 mm × 2 mm ) (LeForte System Bone Screw®) were implanted in the mandible of rats: Group A (pure titanium screws, n = 12 ) and Group B (hafnium-coated screws, n = 12 ). The implanted screws’ stability was checked and noted with a specially customised torque apparatus during insertion and removal of implant. The tissue sections were then processed for hematoxylin and eosin and Masson’s trichrome for bone and connective tissue examination, after 4 and 8 weeks of placement. Hafnium coating appears to have offered similar biocompatibility (aspartate transaminase (AST), alanine aminotransferase (ALT), and creatine kinase (CK) enzyme assay), statistically significant improvement (independent Student’s t -test, p < 0.05 ) in insertion torque ( 25.42 ± 3.965 ) and removal torque ( 29.17 ± 2.887 ) than commercially pure titanium with insertion torque ( 22.08 ± .575 ) and removal torque ( 25.42 ± 2.575 ). Hafnium coating in the rat mandible showed promising osseointegration with good tissue biocompatibility. Further human trials of hafnium-coated implants are needed to understand the biological behaviour better to enhance clinical performance.

Molar Septum Expansion with Osseodensification for Immediate Implant Placement, Retrospective Multicenter Study with Up-to-5-Year Follow-Up, Introducing a New Molar Socket Classification

The ideal positioning of immediate implants in molar extraction sockets often requires the osteotomy to be in the interradicular septum, which can be challenging in some cases, with traditional site preparation techniques. Patients who had undergone molar tooth extraction and immediate implant placement at five different centers, and followed up between August 2015 and September 2020, were evaluated. Inclusion criteria were use of the osseodensification technique for implant site preparation. The primary outcome was septum width measurement pre-instrumentation and osteotomy diameter post expansion. Clinical outcomes, such as implant insertion torque (ISQ) and implant survival rate, were also collected. A total of 131 patients, who received 145 immediate implants, were included. The mean overall septum width at baseline was 3.3 mm and the mean osteotomy diameter post instrumentation was 4.65 mm. A total of ten implants failed: seven within the healing period and three after loading; resulting in a cumulative implant survival rate of 93.1%. This retrospective study showed that osseodensification is a predictable method for immediate implant placement with interradicular septum expansion in molar extraction sockets. Furthermore, it allowed the introduction of a new molar socket classification. In the future, well-designed controlled clinical studies are needed to confirm these results and further explore the potential advantages of this technique.

The effects of locking inserts and overtorque on the mechanical properties of a large fragment locking compression plate

Purpose The study was to determine the effect of locking hole inserts and their insertion torque on the fatigue life of a large fragment Locking Compression Plate (LCP) under bending forces. Methods Fatigue strength of the LCP was examined using cyclic three-point bend testing at 80% yield strength of the construct. Locking hole inserts were used in 2, 4, and 6-hole of a 12-hole plate to simulate three different working lengths. Within each working length, plates were tested without locking inserts serving as the control group. In the experimental groups, inserts were tightened to manufacturer recommendations (4 Nm) and using overtorque (8 Nm). Results Significantly fewer cycles to failure were observed in control groups versus the locking hole insert groups for all working lengths (2-hole: 4 Nm p = 0.003, 8 Nm p = 0.003; 4-hole: 4 Nm p = 0.02, 8 Nm p < 0.001; 6-hole: 4 Nm p = 0.004, 8 Nm p < 0.001). There was a statistically significant increase in fatigue strength when using overtorque in the 4-hole (p = 0.04) and 6-hole (p = 0.01) defect groups. This was not shown in the 2-hole defect group (p = 0.99). Conclusions By placing locking inserts in the empty locking regions of Combi holes along the working length, the number of cycles to failure was increased. Tightening inserts to twice the recommended insertion torque further increased cycles to failure in longer working length models. A longer fatigue life has the potential to decease the incidence of plate failure especially in the setting of delayed union due to poor intrinsic healing capacity, fractures in the geriatric population, osteoporosis and periprosthetic fractures.