Finite Element Analysis of Different Pin Diameter of External Fixator in Treating Tibia Fracture

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Muhammad Hanif Ramlee ◽  
◽  
Nur Amalina Zainudin ◽  
Mohammed Rafiq Abdul Kadir ◽  
◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
External Fixator ◽  
Three Dimensional ◽  
Shaft Fracture ◽  
Element Analysis ◽  
Tibia Shaft Fracture ◽  
Finite Element Software ◽  
Tibia Bone ◽  
Tibia Shaft

Biomechanical perspective of external fixator is one of the biggest elements that should be considered in treating fracture bone. This is due to the mechanical behavior of the structure could be analyzed and optimized in order to avoid failure, increase bone fracture healing rate and prevents preterm screw loosening. There are three significant factors that affect the stability of external fixator and those are the placement of pin at the bone, configuration and components of external fixator. All these factors contribute to a question, what is the optimum pin diameter which exerts good stress distribution? To date, the research on the above-mentioned factors are limited in the literature. Therefore, this study was conducted to evaluate the unilateral external fixator with different pin sizes in treating tibia shaft fracture via the finite element method. First and foremost, the development of the tibia shaft fracture was conducted using Mimics software. The computed tomography (CT) data image was utilized to develop three-dimensional tibia bone followed by crafting fracture on the bone. Meanwhile, the unilateral external fixator was developed using SolidWorks software. In this study, five pin diameters (4.5, 5.0, 5.5, 6.0 and 6.5 mm) were developed and analyzed. Both tibia bone and external fixator were meshed in 3-matic software. Simulation of this configuration took place in a finite element software, Marc.Mentat. From the findings, it is shown that the larger diameter of pin demonstrated the lowest stress distribution. The size of the 5.5mm pin shows optimum diameter in terms of stress distribution with the value of 21.50 MPa in bone and 143.33 MPa in fixator. Meanwhile the displacement value of 1.42mm in bone and 1.20mm in fixator. In conclusion, it is suggested that the pin diameter of 5.5 mm is the most favorable option in treating tibia shaft fracture in terms of mechanical perspective.

scholarly journals Biomechanical evaluation of pin placement of external fixator in treating tranverse tibia fracture: Analysis on first and second cortex of cortical bone

2019 ◽  
Vol 15 (1) ◽  
pp. 75-79
Author(s):  
Muhammad Hanif Hanif Ramlee ◽  
Nur Amalina Zainudin ◽  
Hadafi Fitri Mohd Latip ◽  
Gan Hong Seng ◽  
Evelyn Garcia-Nieto ◽  
...  
Keyword(s):  
Finite Element ◽  
External Fixator ◽  
Bone Fracture ◽  
Three Dimensional ◽  
Tibia Fracture ◽  
Finite Element Software ◽  
Tibia Bone ◽  
Optimum Stability ◽  
Ct Data ◽  
The Stability

Biomechanical perspective of external fixator is one of the greatest factor to consider in successfully treating bone fracture. This is due to the fact that mechanical behavior of the structure can be analyzed and optimized in order to avoid mechanical failure, increase bone fracture healing rate and prevent pre-term screw loosening. There are three significant factors that affect the stability of external fixator which are the placement of pin at the bone, configuration and components of external fixator. These factors lead to one question: what is the optimum pin placement in which exerts optimum stability? To date, literature on above mentioned factors is limited. Therefore, we conducted a study to evaluate the uniplanar-unilateral external fixator for two different pin placement techniques in treating transverse tibia fracture via finite element method. The study was started off with the development of transverse tibia fracture using Mimics software. Computed tomography (CT) data image was utilized to develop three dimensional tibia bone followed by crafting fracture on the bone. Meanwhile, the external fixator was developed using SolidWork software. Both tibia bone and external fixator were meshed in 3-matic software with triangular mesh element. Simulation of this configuration was took place in a finite element software, Marc.Mentat software. A load of 400 N was applied to the proximal tibia bone in order to simulate stance phase of a gait cycle.  From the findings, the pin placement at the second cortex of bone provided optimum stability in terms of stress distribution and displacement, which should be considered for better treatment for transverse tibia fracture. On the other hand, the pin placement at first cortex should be avoided to prevent many complications.

scholarly journals Three-Dimensional Finite Element Analysis of Stress Distribution in a Tooth Restored with Full Coverage Machined Polymer Crown

2021 ◽  
Vol 11 (3) ◽  
pp. 1220
Author(s):  
Azeem Ul Yaqin Syed ◽  
Dinesh Rokaya ◽  
Shirin Shahrbaf ◽  
Nicolas Martin
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Intraoral Scanner ◽  
Element Analysis ◽  
Dental Ceramic ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Ceramic Crown

The effect of a restored machined hybrid dental ceramic crown–tooth complex is not well understood. This study was conducted to determine the effect of the stress state of the machined hybrid dental ceramic crown using three-dimensional finite element analysis. Human premolars were prepared to receive full coverage crowns and restored with machined hybrid dental ceramic crowns using the resin cement. Then, the teeth were digitized using micro-computed tomography and the teeth were scanned with an optical intraoral scanner using an intraoral scanner. Three-dimensional digital models were generated using an interactive image processing software for the restored tooth complex. The generated models were imported into a finite element analysis software with all degrees of freedom concentrated on the outer surface of the root of the crown–tooth complex. To simulate average occlusal load subjected on a premolar a total load of 300 N was applied, 150 N at a buccal incline of the palatal cusp, and palatal incline of the buccal cusp. The von Mises stresses were calculated for the crown–tooth complex under simulated load application was determined. Three-dimensional finite element analysis showed that the stress distribution was more in the dentine and least in the cement. For the cement layer, the stresses were more concentrated on the buccal cusp tip. In dentine, stress was more on the cusp tips and coronal 1/3 of the root surface. The conventional crown preparation is a suitable option for machined polymer crowns with less stress distribution within the crown–tooth complex and can be a good aesthetic replacement in the posterior region. Enamic crowns are a good viable option in the posterior region.

Finite Element Analysis of Poor Distal Contact of the Femoral Component of a Cementless Hip Endoprosthesis

1993 ◽  
Vol 207 (4) ◽  
pp. 255-261 ◽  
Author(s):  
M Taylor ◽  
E W Abel
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Influencing Factor ◽  
Three Dimensional ◽  
Stress Distributions ◽  
Element Analysis ◽  
Hip Endoprosthesis ◽  
Applied Loading ◽  
Femoral Geometry ◽  
Contact Models

The difficulty of achieving good distal contact between a cementless hip endoprosthesis and the femur is well established. This finite element study investigates the effect on the stress distribution within the femur due to varying lengths of distal gap. Three-dimensional anatomical models of two different sized femurs were generated, based upon computer tomograph scans of two cadaveric specimens. A further six models were derived from each original model, with distal gaps varying from 10 to 60 mm in length. The resulting stress distributions within these were compared to the uniform contact models. The extent to which femoral geometry was an influencing factor on the stress distribution within the bone was also studied. Lack of distal contact with the prosthesis was found not to affect the proximal stress distribution within the femur, for distal gap lengths of up to 60 mm. In the region of no distal contact, the stress within the femur was at normal physiological levels associated with the applied loading and boundary conditions. The femoral geometry was found to have little influence on the stress distribution within the cortical bone. Although localized variations were noted, both femurs exhibited the same general stress distribution pattern.

scholarly journals Three-Dimensional Finite Element Analysis of the Veneer—Framework Thickness in an All-Ceramic Implant Supported Fixed Partial Denture

Ceramics ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 199-207
Author(s):  
Lohitha Kalluri ◽  
Bernard Seale ◽  
Megha Satpathy ◽  
Josephine F. Esquivel-Upshaw ◽  
Yuanyuan Duan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Ct Scanner ◽  
Element Analysis ◽  
Partial Denture ◽  
Fixed Partial Denture ◽  
Occlusal Surfaces ◽  
All Ceramic

This study was performed as an adjunct to an existing clinical study to validate the effect of veneer: framework thickness ratio on stress distribution in an implant-supported all-ceramic fixed partial denture. Two commercially available titanium dental implants with corresponding customized abutments and a patient-retrieved all-ceramic fixed partial denture were scanned using a high-resolution micro-CT scanner. Reconstructed 3D objects, along with a simulated bone surface, were incorporated into a non-manifold assembly and meshed simultaneously using Simpleware software (Synopsys Simpleware ScanIP Version P-2019.09; Mountain View, CA). Three such volume meshes (Model A, Model B, Model C) corresponding to veneer: framework thickness ratios of 3:1, 1:1, and 1:3 respectively were created, and exported to a finite element analysis software (ABAQUS). An axial load of 110 N was applied uniformly on the occlusal surfaces to calculate the static stresses and contour plots were generated in the post-processing module. From the data obtained, we observed optimum stress distribution in Model B. Also, the tensile stresses were concentrated in the posterior connector region of the prosthesis in all three models tested. Within the limitations of this study, we can conclude that equal thickness of veneer and framework layers would aid in better stress distribution.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

Finite Element Analysis of the Effect of Surface Hardening Depth in Port Crane Wheel

2011 ◽  
Vol 291-294 ◽  
pp. 3282-3286 ◽  
Author(s):  
Jiang Wei Wu ◽  
Peng Wang
Keyword(s):  
Finite Element ◽  
Surface Hardening ◽  
Three Dimensional ◽  
Element Model ◽  
Contact Stresses ◽  
Numerical Results ◽  
Element Analysis ◽  
Finite Element Software ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In port crane industry, the surface hardening technique is widely used in order to improve the strength of wheel. But the hardening depth is chosen only by according to the experience, and the effect of different hardened depths is not studied theoretically. In this paper, the contact stresses in wheel with different hardening depth have been analyzed by applying three-dimensional finite element model. Based on this model, the ANSYS10.0 finite element software is used. The elastic wheel is used to verify the numerical results with the Hertz’s theory. Three different hardening depths, namely 10mm, 25mm and whole hardened wheel, under three different vertical loads were applied. The effect of hardening depth of a surface hardened wheel is discussed by comparing the contact stresses and contact areas from the numerical results.

Effects of Sheet Thickness on Residual Stress Distribution by Laser Shock Processing of 7050-T7451 Aluminum Alloy

2011 ◽  
Vol 189-193 ◽  
pp. 3778-3781
Author(s):  
Yin Fang Jiang ◽  
Lei Fang ◽  
Zhi Fei Li ◽  
Zhen Zhou Tang
Keyword(s):  
Finite Element ◽  
Aluminum Alloy ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Sheet Thickness ◽  
Laser Shock ◽  
Laser Shock Processing ◽  
Element Analysis ◽  
Finite Element Software ◽  
Shock Processing

Laser shock processing is a technique similar to shot peening that imparts compressive residual stresses in materials for improved fatigue resistance. Finite element analysis techniques have been applied to predict the residual stresses from Laser shock processing. The purpose of this paper is to investigate of the different sheet thickness interactions on the stress distribution during the laser shock processing of 7050-T7451 aluminum alloy by using the finite element software. The results indicate that the sheet thickness has little effects on the compression stress in the depth of sheet, but great impacts on the reserve side.

Sign in / Sign up

Export Citation Format

Share Document