scholarly journals ULTIMATE STRENGTH OF STEEL BEAM-STEEL HOOP CONCRETE COLUMN JOINT PANEL SUBJECTED TO BIAXIAL BENDING AND SHEAR

1994 ◽  
Vol 59 (463) ◽  
pp. 135-142
Author(s):  
Toshiro SUZUKI ◽  
Katsuki TAKIGUCHI ◽  
Hisato HOTTA
Keyword(s):  
Ultimate Strength ◽  
Steel Beam ◽  
Concrete Column ◽  
Biaxial Bending ◽  
Column Joint

scholarly journals ULTIMATE STRENGTH OF STEEL BEAM-STEEL・HOOP・CONCRETE COLUMN JOINT PANEL WITH TRIANGLE STIFFNERS

1990 ◽  
Vol 416 (0) ◽  
pp. 71-78
Author(s):  
Toshiro SUZUKI ◽  
Katsuki TAKIGUCHI ◽  
Hisato HOTTA ◽  
Masahiro KATO
Keyword(s):  
Ultimate Strength ◽  
Steel Beam ◽  
Concrete Column ◽  
Column Joint

STRESS TRANSFER MECHANISM OF STEEL BEAM-STEEL HOOP CONCRETE COLUMN JOINT PANEL WITH TRIANGLE STIFFNERS

1992 ◽  
Vol 441 (0) ◽  
pp. 93-99
Author(s):  
Toshiro SUZUKI ◽  
Katsuki TAKIGUCHI ◽  
Hisato HOTTA ◽  
Hideyuki HAYASHI
Keyword(s):  
Stress Transfer ◽  
Transfer Mechanism ◽  
Steel Beam ◽  
Concrete Column ◽  
Column Joint

Effect of different RC slab widths on the behavior of reinforced concrete column and steel beam-slab subassemblies

2021 ◽  
Vol 229 ◽  
pp. 111639
Author(s):  
Jinjie Men ◽  
Liquan Xiong ◽  
Jiachen Wang ◽  
Guanlei Fan
Keyword(s):  
Reinforced Concrete ◽  
Steel Beam ◽  
Concrete Column ◽  
Reinforced Concrete Column ◽  
Rc Slab

scholarly journals Seismic Behavior and Study of RCS Composite Frame Composed of Steel Beams and Strong Concrete Column

2019 ◽  
Vol 15 (2) ◽  
pp. 142-153
Author(s):  
Ahmadreza Khodabandehlo ◽  
Mohamad Taghi Kazemi
Keyword(s):  
Reinforced Concrete ◽  
Seismic Behavior ◽  
Bending Strength ◽  
Steel Beams ◽  
Steel Beam ◽  
Concrete Column ◽  
Moment Frame ◽  
Reinforced Concrete Column ◽  
Long Span ◽  
Composite Frame

AbstractWith spreading of population and increasing of instruction, and also because of limited resources and materials, the demand for using novel materials in building industry has increased. The reinforced concrete columns and steel beams are used in structures with composite moment frame (RCS). Use of compression strength in proportion with concrete and bending strength of steel beam has bestowed these structures less weight than that of concrete structures and made it easier to access the measure of strong column - weak beam especially within long span in these structures. The most important part of these structures is connection of steel beam with the reinforced concrete column. These connections are divided into two general groups of connection with bracing beam and with bracing column from the joint. This paper aims to study the seismic behavior and parameters of RCS composite frame composed of steel beams and strong concrete column. The finite element method was analyzed by ABAQUS software and data analyzed by Excel.

scholarly journals Improvement of bearing performance on exterior steel beam-reinforced concrete column joints with steel column

2018 ◽  
Author(s):  
Shinya Nakaue ◽  
Yasushi Nishimura
Keyword(s):  
Reinforced Concrete ◽  
Shear Failure ◽  
Maximum Strength ◽  
Punching Shear ◽  
Steel Beam ◽  
Transverse Reinforcement ◽  
Concrete Column ◽  
Bearing Failure ◽  
Reinforced Concrete Column ◽  
Steel Column

To improve the bearing failure behavior of the exterior steel beam-reinforced concrete column joints composed of reinforced concrete columns, joint details using steel column was proposed. Steel column was attached to the lower flanges at right angles to the steel flange. The objective of this study is to clarify the effectiveness of proposed joint details experimentally and theoretically. To clarify the influence of steel column on the bearing failure of the joint, seven T-shaped subassemblages were tested under reversed cyclic loading. All specimens had the same cross sections of the steel beam. The experimental variables were the embedded length of the steel column, whether there is the end plate at the tip of the embedded steel column, and, the arrangement of transverse reinforcement ratio surrounding the steel column. The following remarks can be drawn from the test results. 1) In case of the specimen with a short embedded length of the steel column, the punching shear failure on the upper surface of the steel beam flange was remarkable when the maximum strength was reached. However, in the specimen with long embedded length of steel column, it was not observed the punching shear failure. 2) The maximum strength increased with the embedded length of the steel column. Further, the maximum strength of the specimen with the embedded length of three times of the steel column depths is subjected to bending yield strength of the steel column. 3) It was shown that the transverse reinforcement to surround the steel column and the end plate were necessary to improve the bearing failure of the joint. 

Sign in / Sign up

Export Citation Format

Share Document