scholarly journals SHAKING TABLE TESTS ON A SEISMICALLY-ISOLATED LARGE-SPAN ARCH SUPPORTED BY BASE STRUCTURES

2004 ◽  
Vol 69 (582) ◽  
pp. 87-94 ◽  
Author(s):  
Tetsuya MATSUI ◽  
Keijiro MIZUNO ◽  
Ei SUGIYAMA ◽  
Yoshisato ESAKA ◽  
Tomoya HIBINO
Keyword(s):  
Shaking Table ◽  
Shaking Table Tests ◽  
Large Span ◽  
Seismically Isolated

Shaking Table Tests Examining Seismic Response of Suspended Ceilings Attached to Large-Span Spatial Structures

2018 ◽  
Vol 144 (9) ◽  
pp. 04018152 ◽  
Author(s):  
Yan Lu ◽  
Gilberto Mosqueda ◽  
Qinghua Han ◽  
Yifeng Zhao
Keyword(s):  
Seismic Response ◽  
Shaking Table ◽  
Spatial Structures ◽  
Shaking Table Tests ◽  
Large Span

Shaking Table Tests With Large Test Specimens of Seismically Isolated FBR Plants: Part 2—Damage Test of Reinforced Concrete Wall Structure

2009 ◽  
Author(s):  
Satoru Inaba ◽  
Takuya Anabuki ◽  
Kazutaka Shirai ◽  
Shuichi Yabana ◽  
Seiji Kitamura
Keyword(s):  
Reinforced Concrete ◽  
Seismic Isolation ◽  
Shaking Table Test ◽  
Shaking Table ◽  
Wall Structure ◽  
Shaking Table Tests ◽  
Concrete Wall ◽  
Restoring Force ◽  
Seismically Isolated ◽  
Rubber Bearings

This paper describes the dynamic damage test of a reinforced concrete (RC) wall structure with seismic isolation sysytem. It has been expected that seismically isolated structures are damaged in sudden when the accelerations of the structures exceed a certain level by hardening of the rubber bearings. However, the response behavior and the damage mode have not been observed by experimental test yet. So, shaking table tests were carried out at “E-Defense”, equipping the world’s largest shaking table, located at Miki City, Hyogo prefecture, Japan. The specimen was composed of an upper structure of 600 ton by weight and six lead-rubber bearings (LRBs) of 505 mm in diameter which provide both stiffness and hysteretic damping. The upper structure consisted of a RC mass and four RC walls with counter weight. The RC wall structure was designed so that the damage of the RC wall occurred between the shear force at the hardening of the rubber bearings and that at their breaking. The dimensions of the RC wall were 1600 × 800 × 100 mm (B × H × t). The reinforcement ratios were 2.46% in vertical by D13 (deformed reinforcing bar, 13 mm in diameter) and 1.0% in horizontal by D10. The shaking table test was conducted consecutively by increasing the levels up to 225% of tentative design earthquake motion. Consequently, because of the increase of the structural response by the hardening of the rubber bearings, the damage of the wall structure with seismic isolation system suddenly happened. In addition, the preliminary finite element analysis simulated the test results fairly well, which were the restoring force characteristics, the crack patterns of the RC wall structure and such.

Shaking Table Tests With Large Test Specimens of Seismically Isolated FBR Plants: Part 3—Ultimate Behavior of Upper Structure and Rubber Bearings

2009 ◽  
Author(s):  
Shuichi Yabana ◽  
Kenji Kanazawa ◽  
Seiji Nagata ◽  
Seiji Kitamura ◽  
Takeshi Sano
Keyword(s):  
Seismic Isolation ◽  
Response Spectra ◽  
Shaking Table ◽  
Shaking Table Tests ◽  
Nuclear Facilities ◽  
Restoring Force ◽  
Isolation System ◽  
Seismically Isolated ◽  
Design Earthquake ◽  
Rubber Bearings

This paper describes results of shaking table tests to grasp ultimate behavior of seismic isolation system under extremely strong earthquake motions, including failure of rubber bearings. The results of the shaking table tests are expected to be useful for the design of seismically isolated nuclear facilities, especially fast breeder reactor (FBR) plants. In the test, lead rubber bearings, of which the diameter is 505 mm and about 1/3 scale of a prototype in planning FBR plants, are used; the test specimens are loaded by the largest three-dimensional shaking table in E-defense of National Research Institute for Earth Science and Disaster Prevention (NIED) of Japan. Failure of rubber bearings occurs with amplified tentative design earthquake motions. From the tests, the ultimate responses of the upper structure and rubber bearings are presented. In particular, the change of floor response spectra and restoring force characteristics of rubber bearings according to increase of input motions is discussed. Furthermore, mechanism of the failure of rubber bearings is investigated from the observation of failure surfaces and cut sections, static loading tests, and material tests of rubber bearings. Finally, the function of seismic isolation system after the failure of a part of rubber bearings is confirmed under the tentative design earthquake.

scholarly journals Low-cost hybrid design of masonry structures for developing countries: Shaking table tests

2021 ◽  
Vol 146 ◽  
pp. 106675
Author(s):  
Anastasios Tsiavos ◽  
Anastasios Sextos ◽  
Andreas Stavridis ◽  
Matt Dietz ◽  
Luiza Dihoru ◽  
...  
Keyword(s):  
Developing Countries ◽  
Low Cost ◽  
Shaking Table ◽  
Hybrid Design ◽  
Masonry Structures ◽  
Shaking Table Tests

Shaking-table tests of seismic responses of slender intake tower-hoist chamber systems

2021 ◽  
Vol 242 ◽  
pp. 112517
Author(s):  
Hanyun Zhang ◽  
Cai Jiang ◽  
Shuming Liu ◽  
Liaojun Zhang ◽  
Chen Wang ◽  
...  
Keyword(s):  
Shaking Table ◽  
Shaking Table Tests ◽  
Seismic Responses

Shaking table tests on the seismic responses of underground structures in coral sand

2021 ◽  
Vol 109 ◽  
pp. 103775
Author(s):  
Xuanming Ding ◽  
Yanling Zhang ◽  
Qi Wu ◽  
Zhixiong Chen ◽  
Chenglong Wang
Keyword(s):  
Shaking Table ◽  
Shaking Table Tests ◽  
Seismic Responses ◽  
Underground Structures ◽  
Coral Sand

Damage detection via modal analysis of masonry structures using shaking table tests

2021 ◽  
Author(s):  
Chiara Pepi ◽  
Nicola Cavalagli ◽  
Vittorio Gusella ◽  
Massimiliano Gioffrè
Keyword(s):  
Damage Detection ◽  
Modal Analysis ◽  
Shaking Table ◽  
Masonry Structures ◽  
Shaking Table Tests
Sign in / Sign up

Export Citation Format

Share Document