LUCEFIN GROUP C45 (1.0503), C45E (1.1191), C45R (1.1201)

Alloy Digest ◽  
2020 ◽  
Vol 69 (1) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Temperature ◽  
Physical Properties ◽  
Additional Cost ◽  
Medium Carbon ◽  
Temperature Performance ◽  
Alloy Steels ◽  
Cold Worked

Abstract Lucefin Group C45, C45E, and C45R are medium-carbon (0.42–0.50%), non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C45E and C45R may also be flame or induction hardened. C45, C45E and C45R are widely used for moderately stressed parts. Owing to their low hardenability, their use in the quenched and tempered condition is not recommended for large sizes, as the improvement in mechanical properties over the normalized condition is insufficient to justify the additional cost of heat treatment. This datasheet provides information on composition, physical properties, hardness, and elasticity. It also includes information on high temperature performance as well as forming. Filing Code: CS-203. Producer or source: Lucefin S.p.A.

LUCEFIN GROUP C50 (1.0540), C50E (1.1206), C50R (1.1241)

Alloy Digest ◽  
2020 ◽  
Vol 69 (11) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Physical Properties ◽  
Tensile Properties ◽  
Alloy Steel ◽  
Heat Treating ◽  
Medium Carbon ◽  
Alloy Steels ◽  
Cold Worked ◽  
Lower Carbon

Abstract Lucefin Group C50, C50E, and C50R are medium-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C50E and C50R may also be flame or induction hardened. C50, C50E, and C50R are widely used for moderately stressed parts, where higher strength levels are needed than can be achieved in the lower carbon grades, and where the expense of an alloy steel is not justified. Owing to their low hardenability, their use in the quenched and tempered condition is not recommended for large sizes, as the improvement in mechanical properties over the normalized condition is insufficient to justify the additional cost of heat treatment. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on heat treating, machining, and joining. Filing Code: CS-207. Producer or source: Lucefin S.p.A.

ALUMINUM 319.0

Alloy Digest ◽  
1985 ◽  
Vol 34 (5) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Rear Axle ◽  
Heat Treating ◽  
General Purpose ◽  
Temperature Performance

Abstract ALUMINUM 319.0 is a general-purpose foundry alloy that is moderately responsive to heat treatment. It has excellent casting characteristics and good mechanical properties. Among its many uses are crankcases, housings, engine parts, typewriter frames and rear-axle housings. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as creep and fatigue. It also includes information on low and high temperature performance as well as casting, heat treating, machining, and joining. Filing Code: Al-256. Producer or source: Various aluminum companies.

ARMCO NITRONIC 50 STAINLESS STEEL

Alloy Digest ◽  
1990 ◽  
Vol 39 (4) ◽  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Heat Treating ◽  
Temperature Performance ◽  
Price Range ◽  
Cold Worked ◽  
Ss 304

Abstract ARMCO NITRONIC 50 STAINLESS STEEL provides a combination of corrosion resistance and strength not found in any other commercial material available in its price range. It has good mechanical properties at both elevated and sub-zero temperatures. It does not become magnetic when cold worked. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-304. Producer or source: Baltimore Specialty Steels Corporation. Originally published as Nitronic 50, January 1975, revised April 1990.

ALUMINUM 7075

Alloy Digest ◽  
1973 ◽  
Vol 22 (2) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
Aluminum Alloy ◽  
High Temperature ◽  
Physical Properties ◽  
Heat Treating ◽  
Temperature Performance ◽  
Aluminum 7075

Abstract ALUMINUM 7075 is a wrought precipitation-hardenable aluminum alloy having excellent mechanical properties, workability and response to heat treatment and refrigeration. (This alloy is covered under its previous designation, ALUMINUM 75S, in Alloy Digest Al-5, February 1953). This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Al-179. Producer or source: Various aluminum companies.

LUCEFIN GROUP 37Cr4 (1.7034), 37CrS4 (1.7038)

Alloy Digest ◽  
2020 ◽  
Vol 69 (5) ◽  
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Carbon Content ◽  
Induction Hardening ◽  
Medium Carbon ◽  
Small Section ◽  
Temperature Performance ◽  
Content Classification ◽  
Section Size ◽  
Alloy Steels

Abstract Lucefin Group 37Cr4 and 37CrS4 are medium-carbon, 1% chromium, direct hardening alloy steels that are also suitable for flame and induction hardening. These steels are low hardenability steels in the 0.30 to 0.37 mean carbon content classification. They are used for water-quenched parts of moderate section size and for oil-quenched parts of small section size. This datasheet provides information on composition, physical properties, hardness, and elasticity. It also includes information on high temperature performance as well as forming, machining, and joining. Filing Code: SA-862. Producer or source: Lucefin S.p.A.

ALUMINUM 319

Alloy Digest ◽  
1964 ◽  
Vol 13 (10) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
General Purpose ◽  
Temperature Performance ◽  
Aluminum Company

Abstract Aluminum 319 is a general purpose foundry alloy moderately responsive to heat treatment. It has excellent casting characteristics and good mechanical properties. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as creep and fatigue. It also includes information on low and high temperature performance as well as casting, heat treating, machining, and joining. Filing Code: Al-140. Producer or source: Aluminum Company of America.

ALUMINUM 2011

Alloy Digest ◽  
1978 ◽  
Vol 27 (12) ◽  
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Copper Alloy ◽  
Heat Treating ◽  
Temperature Performance ◽  
Screw Machine ◽  
Aluminum Copper Alloy

Abstract ALUMINUM 2011 is an age-hardenable aluminum-copper alloy to which lead and bismuth are added to make it a free-machining alloy. It has good mechanical properties and was designed primarily for the manufacture of screw-machine products. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Al-32. Producer or source: Various aluminum companies. Originally published October 1955, revised December 1978.

REYNOLDS 390 and A390

Alloy Digest ◽  
1971 ◽  
Vol 20 (8) ◽  
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
High Hardness ◽  
Heat Treating ◽  
Silicon Alloys ◽  
Aluminum Silicon Alloys ◽  
Temperature Performance

Abstract REYNOLDS 390 and A390 are hypereutectic aluminum-silicon alloys having excellent wear resistance coupled with good mechanical properties, high hardness, and low coefficients of expansion. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on high temperature performance and corrosion resistance as well as casting, heat treating, and machining. Filing Code: Al-203. Producer or source: Reynolds Metals Company.

ALX ALLOY

Alloy Digest ◽  
1963 ◽  
Vol 12 (1) ◽  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
High Speed ◽  
Heat Treating ◽  
Temperature Performance ◽  
Cobalt Base

Abstract ALX is a composition of nonferrous materials with a cobalt base containing chromium, tungsten and carbon. This alloy is commonly supplied in the cast-to-shape form, having an as-cast hardness of Rockwell C60-62 and requiring no further heat treatment. ALX is also supplied as cast tool bit material and is useful where conventional high-speed steels or carbides do not function effectively. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as casting, forming, heat treating, and machining. Filing Code: Co-35. Producer or source: Allegheny Ludlum Corporation.

ALUMINUM 6151

Alloy Digest ◽  
1958 ◽  
Vol 7 (7) ◽  
Keyword(s):  
Heat Treatment ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Heat Treating ◽  
Age Hardening ◽  
Temperature Performance ◽  
Aluminum Company ◽  
Aluminum Forging ◽  
Hardening Heat Treatment

Abstract ALUMINUM 6151, formerly A51S Alloy, is an aluminum forging alloy combining good forgeability, strength, and resistance to corrosion. It responds to an age-hardening heat treatment. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue. It also includes information on high temperature performance as well as forming, heat treating, machining, and joining. Filing Code: Al-67. Producer or source: Aluminum Company of America.

Sign in / Sign up

Export Citation Format

Share Document