LUCEFIN GROUP C50 (1.0540), C50E (1.1206), C50R (1.1241)

Alloy Digest ◽  
2020 ◽  
Vol 69 (11) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Physical Properties ◽  
Tensile Properties ◽  
Alloy Steel ◽  
Heat Treating ◽  
Medium Carbon ◽  
Alloy Steels ◽  
Cold Worked ◽  
Lower Carbon

Abstract Lucefin Group C50, C50E, and C50R are medium-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C50E and C50R may also be flame or induction hardened. C50, C50E, and C50R are widely used for moderately stressed parts, where higher strength levels are needed than can be achieved in the lower carbon grades, and where the expense of an alloy steel is not justified. Owing to their low hardenability, their use in the quenched and tempered condition is not recommended for large sizes, as the improvement in mechanical properties over the normalized condition is insufficient to justify the additional cost of heat treatment. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on heat treating, machining, and joining. Filing Code: CS-207. Producer or source: Lucefin S.p.A.

LUCEFIN GROUP C35 (1.0501), C35E (1.1181), C35R (1.1180)

Alloy Digest ◽  
2020 ◽  
Vol 69 (7) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Alloy Steel ◽  
Heat Treating ◽  
Medium Carbon ◽  
Alloy Steels ◽  
Cold Worked ◽  
Lower Carbon

Abstract Lucefin Group C35, C35E, and C35R are medium-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C35E and C35R may also be flame or induction hardened. C35, C35E, and C35R are widely used for moderately stressed parts, where higher strength levels are needed than can be achieved in the lower carbon grades, and where the expense of an alloy steel is not justified. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: CS-205. Producer or source: Lucefin S.p.A.

LUCEFIN GROUP C30 (1.0528), C30E (1.1178), C30R (1.1179)

Alloy Digest ◽  
2020 ◽  
Vol 69 (9) ◽  
Keyword(s):  
Tensile Strength ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
High Tensile Strength ◽  
Medium Carbon ◽  
Alloy Steels ◽  
Cold Worked ◽  
Lower Carbon

Abstract Lucefin Group C30, C30E, and C30R are medium-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C30E and C30R may also be flame or induction hardened. C30, C30E, and C30R are widely used for small, moderately stressed parts, where higher strength levels are needed than can be achieved in the lower carbon grades, and also where toughness is more important than high tensile strength. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: CS-206. Producer or source: Lucefin S.p.A.

LUCEFIN C55 (1.0535), C55E (1.1203), C55R (1.1209)

Alloy Digest ◽  
2021 ◽  
Vol 70 (9) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Medium Carbon ◽  
Wear Characteristics ◽  
Alloy Steels ◽  
Cold Worked ◽  
Lower Carbon

Abstract Lucefin C55, C55E, and C55R are medium-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C55E and C55R may also be flame or induction hardened. C55, C55E, and C55R are used for applications where the higher carbon is needed to improve wear characteristics and where strength levels required are higher than those attainable with the lower carbon grades. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on heat treating, machining, and joining. Filing Code: CS-212. Producer or source: Lucefin S.p.A.

LUCEFIN C60 (1.0601), C60E (1.1221), C60R (1.1223)

Alloy Digest ◽  
2021 ◽  
Vol 70 (10) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
High Carbon ◽  
Wear Characteristics ◽  
Alloy Steels ◽  
Cold Worked ◽  
Lower Carbon

Abstract Lucefin C60, C60E, and C60R are high-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C60E and C60R may also be flame or induction hardened. C60, C60E, and C60R are used for applications where the higher carbon is needed to improve wear characteristics and where strength levels required are higher than those attainable with the lower carbon grades. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: CS-213. Producer or source: Lucefin S.p.A.

CEN C22E (1.1151), C22R (1.1149)

Alloy Digest ◽  
2021 ◽  
Vol 70 (5) ◽  
Keyword(s):  
Tensile Strength ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Low Carbon ◽  
High Tensile Strength ◽  
European Committee ◽  
Alloy Steels ◽  
Cold Worked ◽  
Lower Carbon

Abstract CEN C22E and C22R are low-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. They are typically used for small moderately stressed parts, where higher strength levels are needed than can be achieved in the lower carbon grades, and also where toughness is more important than high tensile strength. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: CS-210. Producer or source: European Committee for Standardization.

LUCEFIN GROUP C40 (1.0511), C40E (1.1186), C40R (1.1189)

Alloy Digest ◽  
2020 ◽  
Vol 69 (4) ◽  
Keyword(s):  
Physical Properties ◽  
Alloy Steel ◽  
Medium Carbon ◽  
Alloy Steels ◽  
Cold Worked ◽  
Lower Carbon

Abstract Lucefin Group C40, C40E, and C40R are medium-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C40E and C40R may also be flame or induction hardened. C40, C40E, and C40R are widely used for moderately stressed parts, where higher strength levels are needed than can be achieved in the lower carbon grades, and where the expense of an alloy steel is not justified. This datasheet provides information on composition, physical properties, hardness, and elasticity. It also includes information on forming, machining, and joining. Filing Code: CS-204. Producer or source: Lucefin S.p.A.

LUCEFIN GROUP C45 (1.0503), C45E (1.1191), C45R (1.1201)

Alloy Digest ◽  
2020 ◽  
Vol 69 (1) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Temperature ◽  
Physical Properties ◽  
Additional Cost ◽  
Medium Carbon ◽  
Temperature Performance ◽  
Alloy Steels ◽  
Cold Worked

Abstract Lucefin Group C45, C45E, and C45R are medium-carbon (0.42–0.50%), non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C45E and C45R may also be flame or induction hardened. C45, C45E and C45R are widely used for moderately stressed parts. Owing to their low hardenability, their use in the quenched and tempered condition is not recommended for large sizes, as the improvement in mechanical properties over the normalized condition is insufficient to justify the additional cost of heat treatment. This datasheet provides information on composition, physical properties, hardness, and elasticity. It also includes information on high temperature performance as well as forming. Filing Code: CS-203. Producer or source: Lucefin S.p.A.

CONDULOY

Alloy Digest ◽  
1953 ◽  
Vol 2 (10) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Physical Properties ◽  
Tensile Properties ◽  
Copper Alloy ◽  
Heat Treating ◽  
Age Hardening ◽  
Beryllium Copper ◽  
Hardening Heat Treatment

Abstract CONDULOY is a low beryllium-copper alloy containing about 1.5% nickel. It responds to age-hardening heat treatment for improved mechanical properties. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on casting, heat treating, machining, and joining. Filing Code: Cu-11. Producer or source: Brush Beryllium Company.

ALUMINUM 319.0

Alloy Digest ◽  
1985 ◽  
Vol 34 (5) ◽  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Shear Strength ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Rear Axle ◽  
Heat Treating ◽  
General Purpose ◽  
Temperature Performance

Abstract ALUMINUM 319.0 is a general-purpose foundry alloy that is moderately responsive to heat treatment. It has excellent casting characteristics and good mechanical properties. Among its many uses are crankcases, housings, engine parts, typewriter frames and rear-axle housings. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as creep and fatigue. It also includes information on low and high temperature performance as well as casting, heat treating, machining, and joining. Filing Code: Al-256. Producer or source: Various aluminum companies.

AISI 3150

Alloy Digest ◽  
1963 ◽  
Vol 12 (3) ◽  
Keyword(s):  
Fracture Toughness ◽  
Physical Properties ◽  
Tensile Properties ◽  
Nickel Alloy ◽  
Elastic Properties ◽  
Alloy Steel ◽  
Heat Treating ◽  
Great Depth ◽  
Medium Carbon ◽  
Steel Mills

Abstract AISI 3150 is a medium carbon, chromium-nickel alloy steel having great depth hardness, high elastic properties and excellent fatigue resistance and toughness. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on heat treating and machining. Filing Code: SA-143. Producer or source: Alloy steel mills and foundries.

Sign in / Sign up

Export Citation Format

Share Document