scholarly journals Consistent Time-to-Failure Tests and Analyses of Adhesive Anchor Systems

2020 ◽  
Vol 10 (4) ◽  
pp. 1527 ◽  
Author(s):  
Krešimir Ninčević ◽  
Ioannis Boumakis ◽  
Stefan Meissl ◽  
Roman Wan-Wendner
Keyword(s):  
Experimental Data ◽  
Viscoelastic Behavior ◽  
Tensile Load ◽  
Sustained Load ◽  
Time To Failure ◽  
Sigmoid Function ◽  
Widespread Application ◽  
Pull Out ◽  
Nonlinear Viscoelastic ◽  
Anchor Systems

Motivated by tunnel accidents in the recent past, several investigations into the sustained load behavior of adhesive anchors have been initiated. Nevertheless, the reliable lifetime prediction of bonded anchor systems based on a relatively short testing period still represents an unsolved challenge due to the complex nonlinear viscoelastic behavior of concrete and adhesives alike. This contribution summarizes the results of a comprehensive experimental investigation and systematically carried out time-to-failure analysis performed on bonded anchors under sustained tensile load. Two different adhesive materials that find widespread application in the building industry were used, one epoxy and one vinylester based. Performed experiments include full material characterizations of concrete and the adhesives, bonded anchor pull-out tests at different loading rates, and time-to-failure sustained load tests. All anchor tests are performed in a confined configuration with close support. After a thorough review of available experimental data and analysis methods in the literature, the experimental data are presented with the main goal to (i) provide guidance for the analysis of load versus time-to-failure test data, and (ii) to derive a set of recommendations for efficient time-to-failure tests having in mind the needs associated with different analysis techniques. Finally, a new approach based on a sigmoid function, previously used only for concrete, is for the first time applied to bonded anchors systems and compared to the established regression models.

scholarly journals Creep rate based time-to-failure prediction of adhesive anchor systems under sustained load

2019 ◽  
Vol 178 ◽  
pp. 107389 ◽  
Author(s):  
Ioannis Boumakis ◽  
Krešimir Ninčević ◽  
Jan Vorel ◽  
Roman Wan-Wendner
Keyword(s):  
Creep Rate ◽  
Failure Prediction ◽  
Sustained Load ◽  
Time To Failure ◽  
Anchor Systems

Nonlinear Viscoelastic Finite Element Analysis of Adhesive Joints

1988 ◽  
Vol 16 (3) ◽  
pp. 146-170 ◽  
Author(s):  
S. Roy ◽  
J. N. Reddy
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Viscoelastic Behavior ◽  
Bonded Joints ◽  
Adhesively Bonded ◽  
Element Analysis ◽  
Adhesively Bonded Joints ◽  
Nonlinear Viscoelastic ◽  
Structural Failures ◽  
Updated Lagrangian

Abstract A good understanding of the process of adhesion from the mechanics viewpoint and the predictive capability for structural failures associated with adhesively bonded joints require a realistic modeling (both constitutive and kinematic) of the constituent materials. The present investigation deals with the development of an Updated Lagrangian formulation and the associated finite element analysis of adhesively bonded joints. The formulation accounts for the geometric nonlinearity of the adherends and the nonlinear viscoelastic behavior of the adhesive. Sample numerical problems are presented to show the stress and strain distributions in bonded joints.

scholarly journals Theory of the deformation of aligned polyethylene

2015 ◽  
Vol 471 (2180) ◽  
pp. 20150171 ◽  
Author(s):  
A. Hammad ◽  
T. D. Swinburne ◽  
H. Hasan ◽  
S. Del Rosso ◽  
L. Iannucci ◽  
...  
Keyword(s):  
Load Transfer ◽  
Tensile Load ◽  
Equation Of Motion ◽  
Dislocation Dynamics ◽  
Viscoelastic Deformation ◽  
Transfer Length ◽  
Soliton Dynamics ◽  
Fluctuation Dissipation ◽  
Pull Out ◽  
Definition Of

Solitons are proposed as the agents of plastic and viscoelastic deformation in aligned polyethylene. Interactions between straight, parallel molecules are mapped rigorously onto the Frenkel–Kontorova model. It is shown that these molecular interactions distribute an applied load between molecules, with a characteristic transfer length equal to the soliton width. Load transfer leads to the introduction of tensile and compressive solitons at the chain ends to mark the onset of plasticity at a well-defined yield stress, which is much less than the theoretical pull-out stress. Interaction energies between solitons and an equation of motion for solitons are derived. The equation of motion is based on Langevin dynamics and the fluctuation–dissipation theorem and it leads to the rigorous definition of an effective mass for solitons. It forms the basis of a soliton dynamics in direct analogy to dislocation dynamics. Close parallels are drawn between solitons in aligned polymers and dislocations in crystals, including the configurational force on a soliton. The origins of the strain rate and temperature dependencies of the viscoelastic behaviour are discussed in terms of the formation energy of solitons. A failure mechanism is proposed involving soliton condensation under a tensile load.

Identification of Nonlinear Viscoelastic Models of Flexible Polyurethane Foam From Uniaxial Compression Data

2016 ◽  
Vol 138 (2) ◽  
Author(s):  
Yousof Azizi ◽  
Patricia Davies ◽  
Anil K. Bajaj
Keyword(s):  
Uniaxial Compression ◽  
Viscoelastic Model ◽  
Viscoelastic Behavior ◽  
Model Parameters ◽  
Viscoelastic Models ◽  
Nonlinear Viscoelastic ◽  
Compression Data ◽  
Computationally Intensive ◽  
Nonlinear Viscoelastic Model ◽  
Flexible Polyurethane

Flexible polyethylene foam is used in many engineering applications. It exhibits nonlinear and viscoelastic behavior which makes it difficult to model. To date, several models have been developed to characterize the complex behavior of foams. These attempts include the computationally intensive microstructural models to continuum models that capture the macroscale behavior of the foam materials. In this research, a nonlinear viscoelastic model, which is an extension to previously developed models, is proposed and its ability to capture foam response in uniaxial compression is investigated. It is hypothesized that total stress can be decomposed into the sum of a nonlinear elastic component, modeled by a higher-order polynomial, and a nonlinear hereditary type viscoelastic component. System identification procedures were developed to estimate the model parameters using uniaxial cyclic compression data from experiments conducted at six different rates. The estimated model parameters for individual tests were used to develop a model with parameters that are a function of strain rates. The parameter estimation technique was modified to also develop a comprehensive model which captures the uniaxial behavior of all six tests. The performance of this model was compared to that of other nonlinear viscoelastic models.

scholarly journals The effect of tissue culture on suture holding strength and degradation in canine tendon

2009 ◽  
Vol 34 (5) ◽  
pp. 643-650 ◽  
Author(s):  
H. OMAE ◽  
C. ZHAO ◽  
Y.-L. SUN ◽  
M. E. ZOBITZ ◽  
S. L. MORAN ◽  
...  
Keyword(s):  
Tissue Culture ◽  
Tensile Load ◽  
Flexor Digitorum Profundus ◽  
Tendon Suture ◽  
Pull Out ◽  
Culture Model ◽  
Static Tensile ◽  
Tissue Culture Model ◽  
Flexor Digitorum ◽  
Pull Out Strength

The purpose of this study was to assess tendon metabolism and suture pull-out strength after simple tendon suture in a tissue culture model. One hundred and twelve flexor digitorum profundus tendons from 28 dogs were cultured for 7, 14, or 21 days with or without a static tensile load. In both groups increased levels of matrix metalloproteinase (MMP) mRNA was noted. Suture pull-out strength did not decrease during tissue culture. While the presence of a static load had no effect on the pull-out strength, it did affect MMP mRNA expression. This tissue culture model could be useful in studying the effect of factors on the tendon-suture interface.

Time to failure modeling of carbon fiber reinforced polymer composites subject to simultaneous tension and one-sided heat flux

2018 ◽  
Vol 52 (18) ◽  
pp. 2503-2514 ◽  
Author(s):  
D Swanson ◽  
J Wolfrum
Keyword(s):  
Heat Flux ◽  
Carbon Fiber ◽  
Tensile Load ◽  
Combined Loading ◽  
Fiber Reinforced Polymers ◽  
Time To Failure ◽  
Fiber Reinforced ◽  
Mechanical Loads ◽  
Failure Times ◽  
Carbon Fiber Reinforced

This study focuses on observing and analyzing the time to failure of carbon fiber reinforced polymers subject to mechanical loading and one-sided heat flux simulating fire damage. The purpose of this investigation is to understand the rate of thermal degradation and mechanical property loss from fire exposure, resulting in catastrophic failure under simultaneous tensile loading. Composite samples of varying thicknesses and layup patterns are subject to a constant tensile load below the ultimate strength of the material. A thermal load is applied to one side by an infrared band heater, emitting a constant heat flux. The time to failure is monitored to determine how long the material can withstand this combined loading condition. A consistent trend is observed for various heat flux settings. High mechanical loads contribute to a shorter time to failure, and low mechanical loads contribute to a longer time to failure. Similarly, higher heat flux settings result in shorter failure times, and lower heat flux settings result in longer failure times. Temperature profiles are created based on heat flux exposure time and position through the sample thickness, establishing failure criteria for different loading conditions. The resulting trends are observed and extrapolated to create a predictive model using an Arrhenius exponential decay function.

scholarly journals Role of smooth muscle activation in the static and dynamic mechanical characterization of human aortas

2022 ◽  
Vol 119 (3) ◽  
pp. e2117232119
Author(s):  
Giulio Franchini ◽  
Ivan D. Breslavsky ◽  
Francesco Giovanniello ◽  
Ali Kassab ◽  
Gerhard A. Holzapfel ◽  
...  
Keyword(s):  
Experimental Data ◽  
Smooth Muscle ◽  
Muscle Activation ◽  
Mechanical Response ◽  
Mechanical Characterization ◽  
Viscoelastic Behavior ◽  
Material Model ◽  
Suitable Material ◽  
Dynamic Mechanical

Experimental data and a suitable material model for human aortas with smooth muscle activation are not available in the literature despite the need for developing advanced grafts; the present study closes this gap. Mechanical characterization of human descending thoracic aortas was performed with and without vascular smooth muscle (VSM) activation. Specimens were taken from 13 heart-beating donors. The aortic segments were cooled in Belzer UW solution during transport and tested within a few hours after explantation. VSM activation was achieved through the use of potassium depolarization and noradrenaline as vasoactive agents. In addition to isometric activation experiments, the quasistatic passive and active stress–strain curves were obtained for circumferential and longitudinal strips of the aortic material. This characterization made it possible to create an original mechanical model of the active aortic material that accurately fits the experimental data. The dynamic mechanical characterization was executed using cyclic strain at different frequencies of physiological interest. An initial prestretch, which corresponded to the physiological conditions, was applied before cyclic loading. Dynamic tests made it possible to identify the differences in the viscoelastic behavior of the passive and active tissue. This work illustrates the importance of VSM activation for the static and dynamic mechanical response of human aortas. Most importantly, this study provides material data and a material model for the development of a future generation of active aortic grafts that mimic natural behavior and help regulate blood pressure.

Sign in / Sign up

Export Citation Format

Share Document