scholarly journals Origin and Justification of the Use of the Arrhenius Relation to Represent the Reaction Rate of the Thermal Decomposition of a Solid

2021 ◽  
Vol 11 (9) ◽  
pp. 4075
Author(s):  
Benjamin Batiot ◽  
Thomas Rogaume ◽  
Franck Richard ◽  
Jocelyn Luche ◽  
Anthony Collin ◽  
...  

Degradation models are commonly used to describe the generation of combustible gases when predicting fire behavior. A model may include many sub-models, such as heat and mass transfer models, pyrolysis models or mechanical models. The pyrolysis sub-models require the definition of a decomposition mechanism and the associated reaction rates. Arrhenius-type equations are commonly used to quantify the reaction rates. Arrhenius-type equations allow the representation of chemical decomposition as a function of temperature. This representation of the reaction rate originated from the study of gas-phase reactions, but it has been extrapolated to liquid and solid decomposition. Its extension to solid degradation needs to be justified because using an Arrhenius-type formulation implies important simplifications that are potentially questionable. This study describes these simplifications and their potential consequences when it comes to the quantification of solid-phase reaction rates. Furthermore, a critical analysis of the existing thermal degradation models is presented to evaluate the implications of using an Arrhenius-type equation to quantify mass-loss rates and gaseous fuel production for fire predictions.

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 330
Author(s):  
Hengli Xiang ◽  
Genkuan Ren ◽  
Yanjun Zhong ◽  
Dehua Xu ◽  
Zhiye Zhang ◽  
...  

Fe3O4@C nanoparticles were prepared by an in situ, solid-phase reaction, without any precursor, using FeSO4, FeS2, and PVP K30 as raw materials. The nanoparticles were utilized to decolorize high concentrations methylene blue (MB). The results indicated that the maximum adsorption capacity of the Fe3O4@C nanoparticles was 18.52 mg/g, and that the adsorption process was exothermic. Additionally, by employing H2O2 as the initiator of a Fenton-like reaction, the removal efficiency of 100 mg/L MB reached ~99% with Fe3O4@C nanoparticles, while that of MB was only ~34% using pure Fe3O4 nanoparticles. The mechanism of H2O2 activated on the Fe3O4@C nanoparticles and the possible degradation pathways of MB are discussed. The Fe3O4@C nanoparticles retained high catalytic activity after five usage cycles. This work describes a facile method for producing Fe3O4@C nanoparticles with excellent catalytic reactivity, and therefore, represents a promising approach for the industrial production of Fe3O4@C nanoparticles for the treatment of high concentrations of dyes in wastewater.


2016 ◽  
Vol 697 ◽  
pp. 510-514 ◽  
Author(s):  
Feng Rui Zhai ◽  
Ke Shan ◽  
Ruo Meng Xu ◽  
Min Lu ◽  
Zhong Zhou Yi ◽  
...  

In the present paper, the ZrB2/h-BN multiphase ceramics were fabricated by SPS (spark plasma sintering) technology at lower sintering temperature using h-BN, ZrO2, AlN and Si as raw materials and B2O3 as a sintering aid. The phase constitution and microstructure of specimens were analyzed by XRD and SEM. Moreover, the effects of different sintering pressures on the densification, microstructure and mechanical properties of ZrB2/h-BN multiphase ceramics were also systematically investigated. The results show that the ZrB2 was obtained through solid phase reaction at different sintering pressures, and increasing sintering pressure could accelerate the formation of ZrB2 phase. As the sintering pressure increasing, the fracture strength and toughness of the sintered samples had a similar increasing tendency as the relative density. The better comprehensive properties were obtained at given sintering pressure of 50MPa, and the relative density, fracture strength and toughness reached about 93.4%, 321MPa and 3.3MPa·m1/2, respectively. The SEM analysis shows that the h-BN grains were fine and uniform, and the effect of sintering pressure on grain size was inconspicuous. The distribution of grain is random cross array, and the fracture texture was more obvious with the increase of sintering pressure. The fracture mode of sintered samples remained intergranular fracture mechanism as sintering pressure changed, and the grain refinement, grain pullout and crack deflection helped to increase the mechanical properties.


1980 ◽  
Vol 18 (3) ◽  
pp. 469-476 ◽  
Author(s):  
Ľ. Žúrková ◽  
K. Gáplovská ◽  
V. Suchá

Sign in / Sign up

Export Citation Format

Share Document