scholarly journals Degradation of Mechanical Behavior of Sandstone under Freeze-Thaw Conditions with Different Low Temperatures

2021 ◽  
Vol 11 (22) ◽  
pp. 10653
Author(s):  
Jingwei Gao ◽  
Chao Xu ◽  
Yan Xi ◽  
Lifeng Fan
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Mechanical Behavior ◽  
Energy Absorption ◽  
Uniaxial Compressive Strength ◽  
Dynamic Strength ◽  
Freezing Temperature ◽  
P Wave ◽  
Freeze Thaw ◽  
P Wave Velocity

This study investigated the effects of freezing temperature under freeze-thaw cycling conditions on the mechanical behavior of sandstone. First, the sandstone specimens were subjected to 10-time freeze-thaw cycling treatments at different freezing temperatures (−20, −40, −50, and −60 °C). Subsequently, a series of density, ultrasonic wave, and static and dynamic mechanical behavior tests were carried out. Finally, the effects of freezing temperature on the density, P-wave velocity, stress–strain curves, static and dynamic uniaxial compressive strength, static elastic modulus, and dynamic energy absorption of sandstone were discussed. The results show that the density slightly decreases as temperature decreases, approximately by 1.0% at −60 °C compared with that at 20 °C. The P-wave velocity, static and dynamic uniaxial compressive strength, static elastic modulus, and dynamic energy absorption obviously decrease. As freezing temperature decreases from 20 to −60 °C, the static uniaxial compressive strength, static elastic modulus, dynamic strength, and dynamic energy absorption of sandstone decrease by 16.8%, 21.2%, 30.8%, and 30.7%, respectively. The dynamic mechanical behavior is more sensitive to the freezing temperature during freeze-thawing cycling compared with the static mechanical behavior. In addition, a higher strain rate can induce a higher dynamic strength and energy absorption.

scholarly journals Analysis of Effects of Rock Physical Properties Changes from Freeze-Thaw Weathering in Ny-Ålesund Region: Part 1—Experimental Study

2020 ◽  
Vol 10 (5) ◽  
pp. 1707 ◽  
Author(s):  
Keunbo Park ◽  
Kiju Kim ◽  
Kichoel Lee ◽  
Dongwook Kim
Keyword(s):  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Wave Velocity ◽  
Meteorological Data ◽  
P Wave ◽  
Rock Properties ◽  
Shore Hardness ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
P Wave Velocity

In order to investigate the weathering characteristics of rocks in response to freeze-thaw conditions in northern latitudes, we analysed meteorological data from the Ny-Ålesund region in Norway, and observed changes in the physical and mechanical properties of rocks of dolomite and quartzite. To assess the effects of freeze-thaw weathering on these rock properties, 900 cycles of long-term freeze-thaw tests were conducted for the sampled rocks in two locations. P-wave velocity, absorption, shore hardness, and the uniaxial compressive strength of the sampled rocks were measured at every 150 cycles in order to analyse physical and mechanical mediator variables of freeze-thaw weathering. It was found that an increasing number of freeze-thaw cycle on the sampled rocks decreases uniaxial compressive strength, shore hardness, and P-wave velocity and increases absorption.

Comparative experimental study on physical and mechanical properties of quartz sandstone after water-cooling and natural-cooling under high temperature

2021 ◽  
pp. qjegh2020-181
Author(s):  
Haopeng Jiang ◽  
Annan Jiang ◽  
Fengrui Zhang
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Uniaxial Compressive Strength ◽  
Heating Temperature ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Water Cooling ◽  
Average Value ◽  
Cooling Methods

Experimental tests were conducted to study the influence of natural cooling and water cooling on the physical and mechanical properties of quartz sandstone. This study aims to understand the effect of different cooling methods on the physical and mechanical properties of quartz sandstone (such as mass, volume, density, P-wave velocity, elastic modulus, uniaxial compressive strength, etc.). The results show that the uniaxial compressive strength (UCS) and elastic modulus(E) of the specimens cooled by natural-cooling and water-cooling decrease with heating temperature. At 800℃, after natural cooling and water cooling, the average value of UCS decreased by 34.65% and 57.90%, and the average value of E decreased by 87.66% and 89.05%, respectively. Meanwhile, scanning electron microscope (SEM) images were used to capture the development of microcracks and pores within the specimens after natural-cooling and water-cooling, and it was found that at the same temperature, water cooling treatment was more likely to cause microcracks and pores, which can cause more serious damage to the quartz sandstone. These results confirm that different cooling methods have different effects on the physical and mechanical properties of quartz sandstone, and provide a basis for the stability prediction of rock mass engineering such as tunnel suffering from fire.

scholarly journals Estimating uniaxial compressive strength, density and porosity of rocks from the p-wave velocity measurements in-situ and in the laboratory

2021 ◽  
Vol 74 (4) ◽  
pp. 521-528
Author(s):  
André Cezar Zingano ◽  
Paulo Salvadoretti ◽  
Rafael Ubirajara Rocha ◽  
João Felipe Coimbra Leite Costa
Keyword(s):  
Compressive Strength ◽  
Uniaxial Compressive Strength ◽  
Wave Velocity ◽  
P Wave ◽  
Velocity Measurements ◽  
P Wave Velocity

scholarly journals Applying Statistical Analysis and Machine Learning for Modeling the UCS from P-Wave Velocity, Density and Porosity on Dry Travertine

2020 ◽  
Vol 10 (13) ◽  
pp. 4565
Author(s):  
Manuel Saldaña ◽  
Javier González ◽  
Ignacio Pérez-Rey ◽  
Matías Jeldres ◽  
Norman Toro
Keyword(s):  
Machine Learning ◽  
Compressive Strength ◽  
Statistical Analysis ◽  
Uniaxial Compressive Strength ◽  
Wave Velocity ◽  
Accurate Determination ◽  
Effective Porosity ◽  
P Wave ◽  
Strength Parameter ◽  
P Wave Velocity

In the rock mechanics and rock engineering field, the strength parameter considered to characterize the rock is the uniaxial compressive strength (UCS). It is usually determined in the laboratory through a few statistically representative numbers of specimens, with a recommended minimum of five. The UCS can also be estimated from rock index properties, such as the effective porosity, density, and P-wave velocity. In the case of a porous rock such as travertine, the random distribution of voids inside the test specimen (not detectable in the density-porosity test, but in the compressive strength test) causes large variations on the UCS value, which were found in the range of 62 MPa for this rock. This fact complicates a sufficiently accurate determination of experimental results, also affecting the estimations based on regression analyses. Aiming to solve this problem, statistical analysis, and machine learning models (artificial neural network) was developed to generate a reliable predictive model, through which the best results for a multiple regression model between uniaxial compressive strength (UCS), P-wave velocity and porosity were obtained.

Sign in / Sign up

Export Citation Format

Share Document