scholarly journals Increasing Solar Energy Usage for Dwelling Heating, Using Solar Collectors and Medium Sized Vacuum Insulated Storage Tank

Energies ◽  
2018 ◽  
Vol 11 (7) ◽  
pp. 1832 ◽  
Author(s):  
Janar Kalder ◽  
Andres Annuk ◽  
Alo Allik ◽  
Eugen Kokin
Keyword(s):  
Heat Pump ◽  
Storage Tank ◽  
Storage System ◽  
Heating System ◽  
Heat Energy ◽  
Solar Irradiation ◽  
Water Tank ◽  
Energy Usage ◽  
Solar Heat ◽  
Direct Heating

This article describes a method for increasing the solar heat energy share in the heating of a dwelling. Solar irradiation is high in summer, in early autumn, and in spring, but during that same time, the heat demand of dwellings is low. This article describes a solution for storing solar heat energy in summertime as well as the calculations of the heat energy balance of such a storage system. The solar heat energy is stored in a thermally insulated water tank and used in the heating period. The heat is also stored in the ground if necessary, using the ground loop of the heat pump if the water tank’s temperature rises above a certain threshold. The stored heat energy is used directly for heating if the heat carrier temperature inside the tank is sufficient. If the temperature is too low for direct heating, then the heat pump can be used to extract the stored energy. The calculations are based on the solar irradiation measurements and heating demand data of a sample dwelling. The seasonal storing of solar heat energy can increase the solar heat energy usage and decrease the heat pump working time. The long-term storage tank capacity of 15 m3 can increase the direct heating from solar by 41%. The direct heating system efficiency is 51%.

scholarly journals Development of a hybrid solar cascade heat pump heating system

2021 ◽  
Author(s):  
Jamie Fine
Keyword(s):  
Case Studies ◽  
Co2 Emissions ◽  
Heat Pump ◽  
Thermal Performance ◽  
Heating System ◽  
Solar Heating ◽  
Hot Water ◽  
Solar Irradiation ◽  
Solar Still ◽  
Evacuated Tube

Society’s use of fossil fuels has led to increasingly high levels of CO2 in the atmosphere. These levels have been linked to global average temperature rises, and increases in the severity and frequency of major weather events. To combat these effects, nations around the world have committed to reducing their CO2 emissions, and transition to renewable energy. This thesis focuses on the development of a novel solar heating system, which combines a hybrid solar panel and cascade heat pump. The thesis begins by presenting a high-level literature review of solar and heat pump technologies, followed by the initial design development of the system. Two design iterations are presented, illustrating that the final design was selected because it exhibits improved peak heat output, and reduced sensitivity to panel temperature. Next, a manuscript-based chapter is presented that focuses on utilizing the proposed solar heating system for water distillation. Case studies are presented that compare the performance of the proposed system with a solar still at four different locations. The final conclusion from these studies is that using the proposed system offers area-based performance improvements of 780% compared to a basic solar still. A second manuscript-based study is then presented, which focuses on utilizing the proposed solar heating system for domestic hot water production. Additional case studies are detailed that compare the proposed system to an evacuated tube design, and a single heat pump. The conclusions from these studies are that the proposed system exceeds the performance of the evacuated tube system by up to 64%, and that the proposed system is most beneficial during seasons with higher average dry-bulb temperatures, and increased solar irradiation. A final manuscript-based study is then presented, which focuses on a methodology for improving alternate mode thermal performance estimates for hybrid solar panels. The conclusion from this study is that the proposed methodology can successfully estimate thermal performance within 5% of actual values. Each of these studies contributes to the project goal of developing a novel solar energy heating system, which can be further developed to reduce global CO2 emissions, and reduce the effects of climate change.

scholarly journals Development of a hybrid solar cascade heat pump heating system

2021 ◽  
Author(s):  
Jamie Fine
Keyword(s):  
Case Studies ◽  
Co2 Emissions ◽  
Heat Pump ◽  
Thermal Performance ◽  
Heating System ◽  
Solar Heating ◽  
Hot Water ◽  
Solar Irradiation ◽  
Solar Still ◽  
Evacuated Tube

Society’s use of fossil fuels has led to increasingly high levels of CO2 in the atmosphere. These levels have been linked to global average temperature rises, and increases in the severity and frequency of major weather events. To combat these effects, nations around the world have committed to reducing their CO2 emissions, and transition to renewable energy. This thesis focuses on the development of a novel solar heating system, which combines a hybrid solar panel and cascade heat pump. The thesis begins by presenting a high-level literature review of solar and heat pump technologies, followed by the initial design development of the system. Two design iterations are presented, illustrating that the final design was selected because it exhibits improved peak heat output, and reduced sensitivity to panel temperature. Next, a manuscript-based chapter is presented that focuses on utilizing the proposed solar heating system for water distillation. Case studies are presented that compare the performance of the proposed system with a solar still at four different locations. The final conclusion from these studies is that using the proposed system offers area-based performance improvements of 780% compared to a basic solar still. A second manuscript-based study is then presented, which focuses on utilizing the proposed solar heating system for domestic hot water production. Additional case studies are detailed that compare the proposed system to an evacuated tube design, and a single heat pump. The conclusions from these studies are that the proposed system exceeds the performance of the evacuated tube system by up to 64%, and that the proposed system is most beneficial during seasons with higher average dry-bulb temperatures, and increased solar irradiation. A final manuscript-based study is then presented, which focuses on a methodology for improving alternate mode thermal performance estimates for hybrid solar panels. The conclusion from this study is that the proposed methodology can successfully estimate thermal performance within 5% of actual values. Each of these studies contributes to the project goal of developing a novel solar energy heating system, which can be further developed to reduce global CO2 emissions, and reduce the effects of climate change.

scholarly journals A Domestic Solar/Heat Pump Heating System Incorporating Latent and Stratified Thermal Storage

2008 ◽  
Author(s):  
Christoph Trinkl ◽  
Wilfried Zo¨rner ◽  
Vic Hanby
Keyword(s):  
Latent Heat ◽  
Heat Pump ◽  
Solar Collector ◽  
Energy Demand ◽  
Heat Storage ◽  
Thermal Storage ◽  
Heating System ◽  
System Control ◽  
Latent Heat Storage ◽  
Solar Heat

Both solar and heat pump heating systems are innovative technologies for sustaining ecological heat generation. They are gaining more and more importance due to the accelerating pace of climate change and the rising cost of limited fossil resources. Against this background, a heating system combining solar thermal collectors, heat pump, stratified thermal storage and water/ice latent heat storage has been investigated. The major advantages of the proposed solar/heat pump heating system are considered to be its flexible application (suitable for new and existing buildings because of acceptable space demand) as well as the improvement of solar fraction (extended solar collector utilisation time, enhanced collector efficiency), i.e. the reduction of electric energy demand for the heat pump. In order to investigate and optimise the heating system, a dynamic system simulation model was developed. On this basis, a fundamental control strategy was derived for the overall coordination of the heating system with particular regard to the performance of the two storage tanks. In a simulation study, a fundamental investigation of the heating system configuration was carried out and optimisation derived for the system control as well as the selection of components and their dimensioning. The influence of different parameters on the system performance was identified, where the collector area and the latent heat storage volume were found to be the predominant parameters for system dimensioning. For a modern one-family house, a solar collector area of 30m2 and a latent heat store volume of 12.5m3 are proposed. In this configuration, the heating system reaches a seasonal performance factor of 4.6, meaning that 78% of the building’s and users’ heat demand are delivered by solar energy. The results show that the solar/heat pump heating system can give an acceptable performance using up-to-date components in a state-of-the-art building.

scholarly journals Temperature Measurements on a Solar and Low Enthalpy Geothermal Open-Air Asphalt Surface Platform in a Cold Climate Region

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 979 ◽  
Author(s):  
Caner Çuhac ◽  
Anne Mäkiranta ◽  
Petri Välisuo ◽  
Erkki Hiltunen ◽  
Mohammed Elmusrati
Keyword(s):  
Heat Flux ◽  
Urban Areas ◽  
Storage System ◽  
Energy Resource ◽  
Cold Climate ◽  
Solar Irradiation ◽  
Solar Heat ◽  
Heat Collector ◽  
One Year

Solar heat, already captured by vast asphalt fields in urban areas, is potentially a huge energy resource. The vertical soil temperature profile, i.e., low enthalpy geothermal energy, reveals how efficiently the irradiation is absorbed or radiated back to the atmosphere. Measured solar irradiation, heat flux on the asphalt surface and temperature distribution over a range of depths describe the thermal energy from an asphalt surface down to 10 m depth. In this study, those variables were studied by long-term measurements in an open-air platform in Finland. To compensate the nighttime heat loss, the accumulated heat on the surface should be harvested during the sunny daytime periods. A cumulative heat flux over one year from asphalt to the ground was 70% of the cumulative solar irradiance measured during the same period. However, due to the nighttime heat losses, the net heat flux during 5 day period was only 18% of the irradiance in spring, and was negative during autumn, when the soil was cooling. These preliminary results indicate that certain adaptive heat transfer and storage mechanisms are needed to minimize the loss and turn the asphalt layer into an efficient solar heat collector connected with a seasonal storage system.

A TRNSYS/GROCS Simulation of the TECH House I Ground-Coupled Series Solar-Assisted Heat Pump System

1983 ◽  
Vol 105 (4) ◽  
pp. 446-453 ◽  
Author(s):  
D. J. Roeder ◽  
R. L. Reid
Keyword(s):  
Heat Pump ◽  
Storage Tank ◽  
Heating System ◽  
Electric Resistance ◽  
Heating Season ◽  
Pump System ◽  
Heat Pump System ◽  
Seasonal Performance ◽  
The University ◽  
Better Than

The series solar-assisted heat pump heating system with ground-coupled storage in The University of Tennessee’s TECH House I in Knoxville, Tennessee, has been modeled using TRNSYS/GROCS and was compared to the experimental performance for the 1980–81 heating season. The simulation results were within 8 percent of the experimental measurements. Both simulation and experimental results showed that ground coupling of thermal storage led to the elimination of electric resistance backup heat and a large reduction in the peak heating demand of the house. Results of a parametric study showed that, in general, a ground-coupled storage tank performs better than a storage tank placed outdoors in the Knoxville area. Application of a next generation heat pump resulted in the most significant impact on the seasonal performance factor. As expected, higher performance collectors and larger collector areas led to higher system seasonal performance. An economic analysis showed that the series solar heat pump system cannot economically compete with the stand-alone heat pump system in the Knoxville area.

scholarly journals Seasonal Performance of a Combined Solar, Heat Pump and Latent Heat Storage System

2014 ◽  
Vol 48 ◽  
pp. 689-700 ◽  
Author(s):  
Christian Winteler ◽  
Ralf Dott ◽  
Thomas Afjei ◽  
Bernd Hafner
Keyword(s):  
Latent Heat ◽  
Heat Pump ◽  
Heat Storage ◽  
Storage System ◽  
Latent Heat Storage ◽  
Solar Heat ◽  
Seasonal Performance

scholarly journals Exergy Analysis of Phase-Change Heat-Storage Coupled Solar Heat Pump Heating System

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5552
Author(s):  
Chuanhui Zhu ◽  
Shubin Yan ◽  
Xiaodong Dong ◽  
Wei Zhang ◽  
Biyi Huang ◽  
...  
Keyword(s):  
Solar Energy ◽  
Phase Change ◽  
Heat Pump ◽  
Exergy Analysis ◽  
Heat Storage ◽  
Heating System ◽  
Exergy Loss ◽  
Solar Collectors ◽  
Solar Heat ◽  
Northern Regions

With the rapid development of industrialization, the excessive use of fossil fuels has caused problems such as increased greenhouse gas emissions and energy shortages. The development and use of renewable energy has attracted increased attention. In recent years, solar heat pump heating technology that uses clean solar energy combined with high-efficiency heat pump units is the development direction of clean heating in winter in northern regions. However, the use of solar energy is intermittent and unstable. The low-valley electricity policy is a night-time electricity price policy. Heat pump heating has problems such as frosting and low efficiencies in cold northern regions. To solve these problems, an exergy analysis model of each component of a phase-change heat-storage coupled solar heat pump heating system was established. Exergy analysis was performed on each component of the system to determine the direction of optimization and improvement of the phase-change heat-storage coupled solar heat pump heating system. The results showed that optimizing the heating-end heat exchanger of the system can reduce the exergy loss of the system. When the phase-change heat-storage tank meets the heating demand, its volume should be reduced to lower the exergy loss of the tank heat dissipation. Air-type solar collectors can increase the income exergies of solar collectors.

Design and experimental investigation of a phase change energy storage air-type solar heat pump heating system

2020 ◽  
Vol 179 ◽  
pp. 115506
Author(s):  
Master Yalun Li ◽  
Baoguo Li ◽  
Caiyun Liu ◽  
Shuqiang Su ◽  
Honghai Xiao ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Energy Storage ◽  
Phase Change ◽  
Heat Pump ◽  
Heating System ◽  
Solar Heat

Experimental Testing of a Thermoelectric-Based Hydronic Cooling and Heating Device With Transient Charging of Sensible Thermal Energy Storage Water Tank

2008 ◽  
Author(s):  
Michael J. Kazmierczak ◽  
Sreenidhi Krishnamoorthy ◽  
Abhishek Gupta
Keyword(s):  
Energy Storage ◽  
Heat Exchanger ◽  
Heat Pump ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage Tank ◽  
Hot Water ◽  
System Component ◽  
Water Tank ◽  
Te Modules

Experiments were performed to charge either cold or hot water thermal energy storage tanks using a heat exchanger equipped with multiple thermoelectric (TE) modules. The primary objective was to design a simple, but effective, modular Peltier heat pump system component to provide chilled or hot water for domestic use at the appliance level, and when arranged in multiple unit combinations, a system that can potentially satisfy small home cooling and heating requirements. Moreover, when the TEs are directly energized using solar PV panels, the system provides a renewable, pollution free and off-the-grid solution to supplement home energy needs. The present work focuses on the design and testing of a thermoelectric heat exchanger component that consists of two water channels machined from two aluminum plates with an array of three or five thermoelectric modules placed in between to transiently cool and/or heat the water in the thermal energy storage tank. The water passing over either the cold or hot side of the TE modules is recirculated to charge the cold or hot thermal storage tank, respectively. The temperatures in the prototype Peltier heat exchanger test component and thermal energy water storage tank were measured during both cold tank charging and hot tank charging operation. The thermal efficiencies of TE heat pump cooling/heating system are reported. The effects of TE power input, number of TE units and rate of fluid flow are studied.

Sign in / Sign up

Export Citation Format

Share Document