scholarly journals Comparison between R134a and R1234ze(E) during Flow Boiling in Microfin Tubes

Fluids ◽  
2021 ◽  
Vol 6 (11) ◽  
pp. 417
Author(s):  
Andrea Lucchini ◽  
Igor M. Carraretto ◽  
Thanh N. Phan ◽  
Paola G. Pittoni ◽  
Luigi P. M. Colombo
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Flow Boiling ◽  
Fluid Dynamic ◽  
Saturation Temperature ◽  
Operating Conditions ◽  
Two Fluids ◽  
The Heat Transfer Coefficient

Environmental concerns are forcing the replacement of commonly used refrigerants, and finding new fluids is a top priority. Soon the R134a will be banned, and the hydro-fluoro-olefin (HFO) R1234ze(E) has been indicated as an alternative due to its smaller global warming potential (GWP) and shorter atmospheric lifetime. Nevertheless, for an optimal replacement, its thermo-fluid-dynamic characteristics have to be assessed. Flow boiling experiments (saturation temperature Tsat = 5 °C, mass flux G = 65 ÷ 222 kg·m−2·s−1, mean quality xm = 0.15 ÷ 0.95, quality changes ∆x = 0.06 ÷ 0.6) inside a microfin tube were performed to compare the pressure drop per unit length and the heat transfer coefficient provided by the two fluids. The results were benchmarked for some correlations. In commonly adopted operating conditions, the two fluids show a very similar behavior, while benchmark showed that some correlations are available to properly predict the pressure drop for both fluids. However, only one is satisfactory for the heat transfer coefficient. In conclusion, R1234ze(E) proved to be a suitable drop-in replacement for the R134a, whereas further efforts are recommended to refine and adapt the available predictive models.

scholarly journals Investigation of R134a Flow Boiling Heat Transfer and Pressure Drop in the Evaporator Test Section of Refrigeration System

2018 ◽  
Vol 25 (1) ◽  
pp. 13-31
Author(s):  
Ahmed J. Hamad ◽  
Zahraa Kareem Yasser
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Flow Boiling ◽  
Saturation Temperature ◽  
Operating Conditions ◽  
Refrigeration System ◽  
Test Conditions

This paper presents an experimental and theoretical analysis to investigate the two-phase flow boiling heat transfer coefficient and pressure drop of the refrigerant R-134a in the evaporator test section of the refrigeration system under different operating conditions. The test conditions considered are, for heat flux (13.7-36.6) kW/m2, mass flux (52-105) kg/m2.s, vapor quality (0.2-1) and saturation temperature (-15 to -3.7) ˚C. Experiments were carried out using a test rig for a 310W capacity refrigeration system, which is designed and constructed in the current work. Investigating of the experimental results has revealed that, the enhancement in local heat transfer coefficient for relatively higher heat flux 36.6 kW/m2 was about 38% compared to 13.7 kW/m2 at constant operating conditions. The enhancement in heat transfer coefficient was about 57% when the mass flux increased from 52 kg/m2.s to 105 kg/m2.s at constant test conditions. The enhancement in the heat transfer coefficient was about 64% when the saturation temperature increased from -8 to -3.7 at fixed refrigerant mass velocity and heat flux. The effect of mass velocity on pressure drop was relatively higher by about 27% than that for heat flux at specified test conditions. The comparison between the experimental and theoretical results has shown an acceptable agreement with an average deviation of 21%.  

Microchannel Size Effects on Two-Phase Local Heat Transfer and Pressure Drop in Silicon Microchannel Heat Sinks With a Dielectric Fluid

2007 ◽  
Author(s):  
Tannaz Harirchian ◽  
Suresh V. Garimella
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Flow Boiling ◽  
Heat Sinks ◽  
Dielectric Fluid ◽  
Two Phase ◽  
Microchannel Heat Sinks ◽  
The Heat Transfer Coefficient

Two-phase heat transfer in microchannels can support very high heat fluxes for use in high-performance electronics-cooling applications. However, the effects of microchannel cross-sectional dimensions on the heat transfer coefficient and pressure drop have not been investigated extensively. In the present work, experiments are conducted to investigate the local flow boiling heat transfer in microchannel heat sinks. The effect of channel size on the heat transfer coefficient and pressure drop is studied for mass fluxes ranging from 250 to 1600 kg/m2s. The test sections consist of parallel microchannels with nominal widths of 100, 250, 400, 700, and 1000 μm, all with a depth of 400 μm, cut into 12.7 mm × 12.7 mm silicon substrates. Twenty-five microheaters embedded in the substrate allow local control of the imposed heat flux, while twenty-five temperature microsensors integrated into the back of the substrates enable local measurements of temperature. The dielectric fluid Fluorinert FC-77 is used as the working fluid. The results of this study serve to quantify the effectiveness of microchannel heat transport while simultaneously assessing the pressure drop trade-offs.

Evaporation Heat Transfer and Pressure Drop Characteristics of R32 Inside a Multiport Tube with Microfins

2018 ◽  
Vol 26 (02) ◽  
pp. 1850017 ◽  
Author(s):  
Daisuke Jige ◽  
Shogo Kikuchi ◽  
Hikaru Eda ◽  
Norihiro Inoue ◽  
Shigeru Koyama
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Mass Velocity ◽  
Saturation Temperature ◽  
High Quality ◽  
Frictional Pressure Drop ◽  
Evaporation Heat ◽  
The Heat Transfer Coefficient

This study investigated the evaporation heat transfer and pressure drop characteristics of R32 in a horizontal multiport tube consisting of rectangular minichannels with straight microfins. The heat transfer coefficient and pressure drop were measured for a mass velocity range of 50–400[Formula: see text]kgm[Formula: see text]s[Formula: see text] and heat flux range of 5–20[Formula: see text]kWm[Formula: see text] at a saturation temperature of 15[Formula: see text]C. The frictional pressure drop during an adiabatic two-phase flow was also measured for a mass velocity range of 50–400[Formula: see text]kgm[Formula: see text]s[Formula: see text] and quality range of 0.1–0.9 at the same saturation temperature. The heat transfer coefficient increased with an increasing quality owing to the increase in forced convection. The dryout inception quality increased with the increase in mass velocity. The effects of heat flux on the heat transfer coefficient were small, except in a high-quality region. The heat transfer coefficient in a multiport tube with microfins was higher than that in a multiport tube without microfins in a high-quality region at a mass velocity of 200[Formula: see text]kgm[Formula: see text]s[Formula: see text] and in a low-quality region at a mass velocity of 400[Formula: see text]kgm[Formula: see text]s[Formula: see text]. The effects of mass velocity and microfins on the frictional pressure drop were clarified. It is suspected that the effects of a microfin on the frictional pressured drop can be considered using the hydraulic diameter. The frictional pressure drop was shown to be in good agreement with previous correlations.

Flow Boiling of Refrigerants Inside a Single Circular Minichannel

2008 ◽  
Author(s):  
Stefano Bortolin ◽  
Alberto Cavallini ◽  
Davide Del Col ◽  
Marko Matkovic ◽  
Luisa Rossetto
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Flow Boiling ◽  
Saturation Temperature ◽  
Test Tube ◽  
Inlet Temperature ◽  
Transfer Coefficients ◽  
The Heat Transfer Coefficient

The present paper reports the heat transfer coefficients measured during flow boiling of HFC-32 and HFC-134a in a 0.96 mm diameter single circular channel. The test runs have been performed during vaporization at around 30°C saturation temperature, correspondent to 19.3 bar for R32 and 7.7 bar for R134a. As a peculiar characteristic of the present technique, the heat transfer coefficient is not measured by imposing the heat flux; instead, the boiling process is governed by controlling the inlet temperature of the heating secondary fluid. The quality of the inner surface of the test tube has been measured to check the influence of surface roughness on the heat transfer coefficient. The flow boiling data taken in the present test section is presented and discussed, with particular regard to the effect of heat flux, mass velocity, vapor quality and fluid properties.

Novel Arrangement of Rough Tubes for Heat Flux Improvement

2012 ◽  
Vol 326-328 ◽  
pp. 81-86
Author(s):  
Farshad Farahbod ◽  
Sara Farahmand ◽  
Farzaneh Farahbod
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Crude Oil ◽  
Transfer Coefficient ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Set Up ◽  
The Heat Transfer Coefficient

The objective of the research is to represent a novel arrangement of conical three dimensional rough tubes (FS3D) for heat transfer coefficient enhancement. Experiments were performed with 316 stainless steel tubes of FS3D roughness and hot crude oil was circulated in constant heat flux condition in the related set up. The pressure drop is measured in this set up and compared with the pressure drop in a smooth tube with the same operating conditions. The heat transfer coefficient is one of essential parameters for design of heat transfer equipments and in this experimental work this is investigated for an Iranian crude oil in the FS3D rough tube. The heat transfer coefficient in FS3D rough tubes is higher than in other commercial enhanced tubes. FS3D rough tubes improve the performance of heat transfer equipments and also optimize the size of the mentioned devices. Consequently this type, the FS3D rough tube, is advantageous in energy and cost saving.

scholarly journals Evaporation Heat Transfer and Pressure Drop of Low-Global Warming Potential Refrigerant HFO-1234yf in 6.95-mm Horizontal Smooth Tube

Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6325
Author(s):  
Chang-Hyo Son ◽  
Nam-Wook Kim ◽  
Jung-In Yoon ◽  
Sung-Hoon Seol ◽  
Joon-Hyuk Lee
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Saturation Temperature ◽  
Experimental Conditions ◽  
Evaporation Heat ◽  
R 134A ◽  
The Heat Transfer Coefficient

This study investigated the evaporative heat transfer coefficient and pressure drop characteristics of R-1234yf in a horizontal tube with an inner diameter of 6.95 mm under various experimental conditions. The heat transfer coefficient increased with an increase in quality but showed a sharp decrease in the high-quality area. In addition, the heat transfer coefficient increased as the mass flux, heat flux, and saturation temperature increased. Although R-1234yf and R-134a presented similar heat transfer coefficients, that of R-134a was higher. The pressure drop increased with an increase in the quality and mass flux but decreased with an increase in the saturation temperature. The pressure drop of R-134a was larger than that of R-1234yf. In light of the flow pattern diagram by Taitel and Dukler, most of the experiments were included in the annular flow region, and some regions showed intermittent and stratified corrugated flow regions. Kandlikar’s heat transfer coefficient correlation provided the best prediction for the experimental database, with approximately 84% of the predicted data within ±30%. Moreno Quibén and Thome’s equation for pressure drop predicted approximately 88.71% of the data within ±30%.

Heat Transfer Coefficient, Pressure Gradient, and Flow Patterns of R1234yf Evaporating in Microchannel Tube

2021 ◽  
Vol 143 (4) ◽  
Author(s):  
Houpei Li ◽  
Pega Hrnjak
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Gradient ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Flow Boiling ◽  
Saturation Pressure ◽  
Saturation Temperature ◽  
Heat Mass Transf ◽  
The Heat Transfer Coefficient

Abstract This paper presents the heat transfer coefficient, pressure gradient, and flow pattern of R1234yf in a microchannel tube. Both heat transfer coefficient and pressure gradient are presented against real saturation pressure, while flow pattern captures at the exit of data points are presented in the same plot. The experiment was conducted on a 24-port microchannel tube with an average hydraulic diameter of 0.643 mm. The experiment covers mass flux from 100 to 200 kg m−2s−1, heat flux from 0 to 6 kW m−2, vapor quality from 0 to 1, and inlet saturation temperature from 10 to 30 °C. Comparing the correlations to the HTC measurements at very low quality (about 0.1), Gorenflo, D., and Kenning, D. (2010, Pool Boiling, in: VDI Heat Atlas, 2nd ed, Springer, pp. 757–788) agree with the results. As vapor quality increases, pressure gradient increases. The adiabatic pressure gradient is a strong function of mass flux and saturation pressure (temperature). Flow patterns of R1234yf are also affected by mass flux and saturation pressure. The heat transfer coefficient is a strong function of mass flux and heat flux. The saturation temperature has a smaller effect on HTC in the condition range (10 – 30 °C). Under the test range, the accelerating pressure drop is insignificant compared to friction. Comparing to the results, Mishima, K., and Hibiki, T. (1996, “Some Characteristics of Air-Water Two-Phase Flow in Small Diameter Vertical Tubes,” Int. J. Multiph. Flow, 22(4), pp. 703–712) and Muller-Steinhagen, H., and Heck, K. (1986, “A Simple Friction Pressure Drop Correlation for Two-Phase Flow in Pipes,” Accessed March 1, 2018)., 20, pp. 297–308.) have small mean absolute error (MAE) to predict local pressure gradient. For the heat transfer coefficient, Sun, L., and Mishima, K. (2009, “An Evaluation of Prediction Methods for Saturated Flow Boiling Heat Transfer in Mini-Channels,” Int. J. Heat Mass Transf, 52(23–24), pp. 5323–5329) and Gungor, K. E., and Winterton, R. H. S. (1986, “A General Correlation for Flow Boiling in Tubes and Annuli,” Int. J. Heat Mass Transf, 29(3), pp. 351–358) have an MAE less than 30%.

Heat Transfer and Pressure Drop Correlations for Double-Pass Solar Collector With and Without Porous Media

2002 ◽  
Author(s):  
K. Sopian ◽  
Adam M. Elradi ◽  
Shahrir Abdullah ◽  
K. V. Wong
Keyword(s):  
Heat Transfer ◽  
Porous Media ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Operating Conditions ◽  
Transient Heat Transfer ◽  
Double Pass ◽  
The Heat Transfer Coefficient

Correlations of transient heat transfer and pressure drop have been developed for air flowing through the porous media, which packed a double-pass solar air heater. Various porous media are arranged in different porosities to increase heat transfer, area density and the total heat transfer rate. Transient heat transfer experiments indicate that both the heat transfer coefficient and the friction factor are strong functions of porosity. The heat transfer coefficient and the friction factor are also strong functions of the geometrical parameters of the porous media. A test collector was developed and tested indoors by varying the design features and operating conditions using a halogen-lamp simulator as a radiation source. This type of collector can be used for drying and heat applications such as solar industrial processes, space heating and solar drying of agricultural products.

Sign in / Sign up

Export Citation Format

Share Document