scholarly journals Origin and Application of the Twinned Calcite Strain Gauge

Geosciences ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 296
Author(s):  
Richard H. Groshong
Keyword(s):  
Stress Analysis ◽  
Strain Gauge ◽  
Strain Tensor ◽  
Three Dimensional ◽  
Constant Strain Rate ◽  
Axis Orientation ◽  
Order Of Magnitude ◽  
Rate Experiment ◽  
Strain Axis ◽  
Expected Values

This paper is a personal account of the origin and development of the twinned-calcite strain gauge, its experimental verification, and its relationship to stress analysis. The method allows the calculation of the three-dimensional deviatoric strain tensor based on five or more twin sets. A minimum of about 25 twin sets should provide a reasonably accurate result for the magnitude and orientation of the strain tensor. The opposite-signed strain axis orientation is the most accurately located. Where one strain axis is appreciably different from the other two, that axis is generally within about 10° of the correct value. Experiments confirm a magnitude accuracy of 1% strain over the range of 1–12% axial shortening and that samples with more than 40% negative expected values imply multiple or rotational deformations. If two deformations are at a high angle to one another, the strain calculated from the positive and negative expected values separately provides a good estimate of both deformations. Most stress analysis techniques do not provide useful magnitudes, although most provide a good estimate of the principal strain axis directions. Stress analysis based on the number of twin sets per grain provides a better than order-of-magnitude approximation to the differential stress magnitude in a constant strain rate experiment.

Paper 7: Mechanical Stresses in Pistons, Gudgeon Pins, and Connecting Rods

1966 ◽  
Vol 181 (8) ◽  
pp. 20-30
Author(s):  
B. Lawton ◽  
D. E. G. Crutcher
Keyword(s):  
Stress Analysis ◽  
Strain Gauge ◽  
Three Dimensional ◽  
Mechanical Stresses ◽  
Connecting Rod ◽  
Mechanical Loads ◽  
Theoretical Methods ◽  
Resistance Strain Gauge ◽  
Induced Stresses ◽  
Theoretical Developments

The paper deals with some experimental and theoretical developments in piston, gudgeon pin, and connecting-rod stress analysis. Stresses induced by mechanical loads have been measured experimentally in rigs using resistance strain gauge techniques; and with two- and three-dimensional photoelastic models. Theoretical methods have been devised to predict mechanically induced stresses on a basis which permits direct comparison with rig results.

Detection, Averaging, and 3D Reconstruction of Biological Specimens on Hypercubes (Transputer-based) Computers

1990 ◽  
Vol 48 (1) ◽  
pp. 454-455
Author(s):  
Jose-Maria Carazo ◽  
I. Benavides ◽  
S. Marco ◽  
J.L. Carrascosa ◽  
E.L. Zapata
Keyword(s):  
3D Reconstruction ◽  
3D Structure ◽  
Three Dimensional ◽  
Software Tools ◽  
Mapping Method ◽  
Computer Architectures ◽  
Parallel Computer ◽  
Reconstruction Process ◽  
Computing Power ◽  
Order Of Magnitude

Obtaining the three-dimensional (3D) structure of negatively stained biological specimens at a resolution of, typically, 2 - 4 nm is becoming a relatively common practice in an increasing number of laboratories. A combination of new conceptual approaches, new software tools, and faster computers have made this situation possible. However, all these 3D reconstruction processes are quite computer intensive, and the middle term future is full of suggestions entailing an even greater need of computing power. Up to now all published 3D reconstructions in this field have been performed on conventional (sequential) computers, but it is a fact that new parallel computer architectures represent the potential of order-of-magnitude increases in computing power and should, therefore, be considered for their possible application in the most computing intensive tasks.We have studied both shared-memory-based computer architectures, like the BBN Butterfly, and local-memory-based architectures, mainly hypercubes implemented on transputers, where we have used the algorithmic mapping method proposed by Zapata el at. In this work we have developed the basic software tools needed to obtain a 3D reconstruction from non-crystalline specimens (“single particles”) using the so-called Random Conical Tilt Series Method. We start from a pair of images presenting the same field, first tilted (by ≃55°) and then untilted. It is then assumed that we can supply the system with the image of the particle we are looking for (ideally, a 2D average from a previous study) and with a matrix describing the geometrical relationships between the tilted and untilted fields (this step is now accomplished by interactively marking a few pairs of corresponding features in the two fields). From here on the 3D reconstruction process may be run automatically.

Scanning-tunneling spectroscopy on conjugated polymer films

2003 ◽  
Vol 771 ◽  
Author(s):  
M. Kemerink ◽  
S.F. Alvarado ◽  
P.M. Koenraad ◽  
R.A.J. Janssen ◽  
H.W.M. Salemink ◽  
...  
Keyword(s):  
Polymer Films ◽  
Conjugated Polymer ◽  
Three Dimensional ◽  
Field Enhancement ◽  
Direct Consequence ◽  
Scanning Tunneling Spectroscopy ◽  
Tunneling Spectroscopy ◽  
Band Alignment ◽  
Scanning Tunneling ◽  
Order Of Magnitude

AbstractScanning-tunneling spectroscopy experiments have been performed on conjugated polymer films and have been compared to a three-dimensional numerical model for charge injection and transport. It is found that field enhancement near the tip apex leads to significant changes in the injected current, which can amount to more than an order of magnitude, and can even change the polarity of the dominant charge carrier. As a direct consequence, the single-particle band gap and band alignment of the organic material can be directly obtained from tip height-voltage (z-V) curves, provided that the tip has a sufficiently sharp apex.

scholarly journals Small footprint optoelectrodes using ring resonators for passive light localization

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Vittorino Lanzio ◽  
Gregory Telian ◽  
Alexander Koshelev ◽  
Paolo Micheletti ◽  
Gianni Presti ◽  
...  
Keyword(s):  
State Of The Art ◽  
Three Dimensional ◽  
Network Activity ◽  
Ring Resonators ◽  
Spatiotemporal Resolution ◽  
Optical Ring Resonators ◽  
Light Localization ◽  
Order Of Magnitude ◽  
Small Footprint

AbstractThe combination of electrophysiology and optogenetics enables the exploration of how the brain operates down to a single neuron and its network activity. Neural probes are in vivo invasive devices that integrate sensors and stimulation sites to record and manipulate neuronal activity with high spatiotemporal resolution. State-of-the-art probes are limited by tradeoffs involving their lateral dimension, number of sensors, and ability to access independent stimulation sites. Here, we realize a highly scalable probe that features three-dimensional integration of small-footprint arrays of sensors and nanophotonic circuits to scale the density of sensors per cross-section by one order of magnitude with respect to state-of-the-art devices. For the first time, we overcome the spatial limit of the nanophotonic circuit by coupling only one waveguide to numerous optical ring resonators as passive nanophotonic switches. With this strategy, we achieve accurate on-demand light localization while avoiding spatially demanding bundles of waveguides and demonstrate the feasibility with a proof-of-concept device and its scalability towards high-resolution and low-damage neural optoelectrodes.

Sign in / Sign up

Export Citation Format

Share Document