scholarly journals Orthogonal Printed Microstrip Antenna Arrays for 5G Millimeter-Wave Applications

Micromachines ◽  
2021 ◽  
Vol 13 (1) ◽  
pp. 53
Author(s):  
Muhammad M. Hossain ◽  
Md Jubaer Alam ◽  
Saeed I. Latif
Keyword(s):  
Millimeter Wave ◽  
Antenna Arrays ◽  
Microstrip Antenna ◽  
Dielectric Substrate ◽  
Impedance Bandwidth ◽  
Simulation Tools ◽  
Optimum Spacing ◽  
Scanning Range ◽  
2D And 3D ◽  
Linear Antenna Arrays

This article presents the design of a planar MIMO (Multiple Inputs Multiple Outputs) antenna comprised of two sets orthogonally placed 1 × 12 linear antenna arrays for 5G millimeter wave (mmWave) applications. The arrays are made of probe-fed microstrip patch antenna elements on a 90 × 160 mm2 Rogers RT/Duroid 5880 grounded dielectric substrate. The antenna demonstrates S11 = −10 dB impedance bandwidth in the following 5G frequency band: 24.25–27.50 GHz. The scattering parameters of the antenna were computed by electromagnetic simulation tools, Ansys HFSS and CST Microwave Studio, and were further verified by the measured results of a fabricated prototype. To achieve a gain of 12 dBi or better over a scanning range of +/−45° from broadside, the Dolph-Tschebyscheff excitation weighting and optimum spacing are used. Different antenna parameters, such as correlation coefficient, port isolation, and 2D and 3D radiation patterns, are investigated to determine the effectiveness of this antenna for MIMO operation, which will be very useful for mmWave cellphone applications in 5G bands.

scholarly journals Millimeter Wave Fabry-Perot Resonator Antenna Fed by CPW with High Gain and Broadband

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Xue-Xia Yang ◽  
Guan-Nan Tan ◽  
Bing Han ◽  
Hai-Gao Xue
Keyword(s):  
Millimeter Wave ◽  
Coplanar Waveguide ◽  
Dielectric Substrate ◽  
High Gain ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Gain Bandwidth ◽  
Broad Bandwidth ◽  
Low Profile ◽  
Fabry Perot

A novel millimeter wave coplanar waveguide (CPW) fed Fabry-Perot (F-P) antenna with high gain, broad bandwidth, and low profile is reported. The partially reflective surface (PRS) and the ground form the F-P resonator cavity, which is filled with the same dielectric substrate. A dual rhombic slot loop on the ground acts as the primary feeding antenna, which is fed by the CPW and has broad bandwidth. In order to improve the antenna gain, metal vias are inserted surrounding the F-P cavity. A CPW-to-microstrip transition is designed to measure the performances of the antenna and extend the applications. The measured impedance bandwidth ofS11less than −10 dB is from 34 to 37.7 GHz (10.5%), and the gain is 15.4 dBi at the center frequency of 35 GHz with a 3 dB gain bandwidth of 7.1%. This performance of the antenna shows a tradeoff among gain, bandwidth, and profile.

scholarly journals A Triple-band Suspended Microstrip Antenna with Symmetrical USlots for WLAN/WiMax Applications

2018 ◽  
Vol 7 (2) ◽  
pp. 41-47 ◽  
Author(s):  
S. B. Behera ◽  
D. Barad ◽  
S. Behera
Keyword(s):  
Microstrip Antenna ◽  
Communication Systems ◽  
Ground Plane ◽  
Dielectric Substrate ◽  
Wireless Communication Systems ◽  
Impedance Bandwidth ◽  
Compact Antenna ◽  
Impedance Characteristics ◽  
Triple Band ◽  
Feeding Techniques

In this study, a triple-band suspended microstrip antenna with symmetrical U-slots is proposed for modern wireless communication systems. The antenna is specifically designed to acquire application in WLAN and WiMAX communication. Symmetrical U-slots in the radiator patch increase the number of resonances and improve the gain response. An appropriate air height was maintained between the ground plane and the radiator patch layer for improving bandwidth operation. The impedance characteristics of the antenna are enhanced using probe feeding techniques. The proposed compact antenna is designed on a single dielectric substrate of (30×25×1.56) mm3 . Parametric analysis of the proposed structure has been realized using IE3D software. This prototype exhibits maximum impedance bandwidth of 750 MHz and gain response of 7.28 dBi. The performance of the structure at three resonating bands i.e., at 3.3 GHz, 3.78 GHz and 5.3 GHz facilitate it to be applicable for WLAN/WiMAX systems.

scholarly journals Design and Analysis of Microstrip Patch Antenna Arrays for Millimeter Wave Wireless Communication

2020 ◽  
Vol 9 (3) ◽  
pp. 281-286
Keyword(s):  
Wireless Communication ◽  
Antenna Array ◽  
Millimeter Wave ◽  
Antenna Arrays ◽  
Patch Antenna ◽  
Return Loss ◽  
Path Loss ◽  
Impedance Bandwidth ◽  
Phase Array ◽  
Wave Band

In present 4G the enormously growing of cellular user and the shortage of bandwidth which results in difficulty to provide a high data rate to each end user. To achieve wider bandwidth millimeter wave technology is considered to solve the problem of bandwidth shortage. This paper presents a 4x1 element circular phase array of inset fed rectangular patch antenna operating in the millimeter wave band (24.81GHz 33GHz). To achieve large impedance bandwidth the array is designed with edge coupled parasitic patch arrangement which provides dual resonance. The designed array used the ring-shaped sequential rotation feeding line to reduce the unwanted side lobe radiation. The design antenna array achieved good return loss – 10dB ≤ S11 ≤ – 18.64dB and maintaining 26% (24.81GHz 33GHz) bandwidth. The antenna array has achieved good return loss S11, -18.64dB at 29.09GHz and VSWR ≤ 1.85 (24.81GHz-33GHz). In millimeter wave wireless communication require high gain antenna to overcome the problem of path loss. The designed array has achieved 10.14dB gain. So the designed will be suitable for the future millimeter-wave wireless communication system.

Millimeter-Wave Microstrip Antenna Arrays with Waveguide Feed Network

Frequenz ◽  
2001 ◽  
Vol 55 (11-12) ◽  
Author(s):  
Wolfgang Menzel ◽  
Marc Schreiner ◽  
Roland Mack ◽  
Pedro J. Navarro Vera
Keyword(s):  
Millimeter Wave ◽  
Antenna Arrays ◽  
Microstrip Antenna ◽  
Feed Network

scholarly journals Microstrip H-Shape Patch Antenna’s Analysis and Layout

2019 ◽  
Vol 8 (10) ◽  
pp. 498-501
Keyword(s):  
Software Design ◽  
Microstrip Antenna ◽  
Cell Phone ◽  
Return Loss ◽  
Dielectric Substrate ◽  
Microstrip Patch Antenna ◽  
Impedance Bandwidth ◽  
Good Match ◽  
Microstrip Patch ◽  
Miniature Antenna

Microstrip Patch Antenna gives low contour and size, so it is utilized in specialized gadgets. It is engraved on a dielectric substrate, supported by a metal board, and directly sustained from a 50Ω coaxial link. By utilizing HFSS software design, it will be replicated. The complex impact of incorporating various methods and by presenting a novel H-shape patch provides truncated contour, extensive bandwidth and returns loss, intense gain and minimized antenna components. This sort of miniature antenna has application in cell phone for Wi-Max, Bluetooth, C-band, S-band and furthermore for different remote applications. The parameters of antenna, for example, bandwidth, return loss, VSWR, directivity and gain are examined and compared with the square patch microstrip antenna. Outcome demonstrates that the antenna has accomplished a good match of impedance, bandwidth, return loss, VSWR, Gain and Directivity

Sign in / Sign up

Export Citation Format

Share Document