scholarly journals Experiments on Temperature Changes of Microbolometer under Blackbody Radiation and Predictions Using Thermal Modeling by COMSOL Multiphysics Simulator

Sensors ◽  
2018 ◽  
Vol 18 (8) ◽  
pp. 2593 ◽  
Author(s):  
Yu-Zhen Deng ◽  
Shiang-Feng Tang ◽  
Hong-Yuan Zeng ◽  
Zheng-Yuan Wu ◽  
Der-Kuo Tung
Keyword(s):  
Heat Transfer ◽  
Thermal Conductance ◽  
Blackbody Radiation ◽  
Heat Transfer Model ◽  
Comsol Multiphysics ◽  
Transfer Model ◽  
Temperature Dependent ◽  
Temperature Changes ◽  
Radiated Energy

In this study, we study a heat transfer model, with the surface of the microbolometer device receiving radiation from blackbody constructed using a COMSOL Multiphysics simulator. We have proposed three kinds of L-type 2-leg and 4-leg with the pixel pitch of 35 μm based on vanadium oxide absorbent membrane sandwiched with top passivated and bottom Si3N4 supporting films, respectively. Under the blackbody radiation, the surface temperature changes and distributions of these samples are simulated and analyzed in detail. The trend of change of the temperature dependent resistance of the four kinds of bolometer devices using the proposed heat transfer model is consistent with the actual results of the change of resistance of 4 samples irradiated with 325 K blackbody located in the front distance of 5 cm. In this paper, ΔT indicates the averaged differences of the top temperature on the suspended membrane and the lowest temperature on the post of legs of the microbolometers. It is shown that ΔT ≈ 17 mK is larger in nominal 2-leg microbolometer device than that of 4-leg one and of 2-leg with 2 μm × 2 μm central square hole and two 7.5 μm × 2 μm slits in suspended films. Additionally, only ΔT ≈ 5 mK with 4-leg microbolometer device under the same radiated energy of 325 K blackbody results from the larger total thermal conductance.

Heat Transfer Modeling of Nanoparticle Packings on a Substrate

2018 ◽  
Author(s):  
Anil Yuksel ◽  
Edward T. Yu ◽  
Michael Cullinan ◽  
Jayathi Murthy
Keyword(s):  
Heat Transfer ◽  
Laser Power ◽  
Thermal Conductance ◽  
Heat Transfer Model ◽  
Experimental Result ◽  
Transfer Model ◽  
Heat Transfer Modeling ◽  
Interfacial Thermal Conductance ◽  
High Laser ◽  
Good Agreement

The temperature evolution of nanoparticle packings on a substrate under high laser power is investigated both experimentally and via numerical simulations. Numerical modeling of temperature distributions in copper nanoparticle packings on a glass substrate is performed and results are compared with experiment under 2.6 kW/cm2 laser power. A coupled electromagnetic-heat transfer model is implemented to understand the nanoparticle temperature distribution. Very good agreement between the coupled electromagnetic-heat transfer model and the experimental results is obtained by matching the interfacial thermal conductance, G, between the nanoparticles using the experimental result in the coupled electromagnetic-heat transfer model.

Bio-heat transfer model of deep brain stimulation-induced temperature changes

2006 ◽  
Vol 3 (4) ◽  
pp. 306-315 ◽  
Author(s):  
Maged M Elwassif ◽  
Qingjun Kong ◽  
Maribel Vazquez ◽  
Marom Bikson
Keyword(s):  
Heat Transfer ◽  
Deep Brain Stimulation ◽  
Brain Stimulation ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Temperature Changes ◽  
Deep Brain

Theoretical Post-Dryout Heat Transfer Model

2018 ◽  
Vol 1 (1) ◽  
pp. 142-150
Author(s):  
Murat Tunc ◽  
Ayse Nur Esen ◽  
Doruk Sen ◽  
Ahmet Karakas
Keyword(s):  
Heat Transfer ◽  
Droplet Diameter ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Operating Pressure ◽  
Vertical Pipe ◽  
Two Phase ◽  
Experimental Values ◽  
Reactor Operating ◽  
Coolant System

A theoretical post-dryout heat transfer model is developed for two-phase dispersed flow, one-dimensional vertical pipe in a post-CHF regime. Because of the presence of average droplet diameter lower bound in a two-phase sparse flow. Droplet diameter is also calculated. Obtained results are compared with experimental values. Experimental data is used two-phase flow steam-water in VVER-1200, reactor coolant system, reactor operating pressure is 16.2 MPa. On heater rod surface, dryout was detected as a result of jumping increase of the heater rod surface temperature. Results obtained display lower droplet dimensions than the experimentally obtained values.

An Engine Heat Transfer Model for Comprehensive Thermal Simulations

2006 ◽  
Author(s):  
Filip Kitanoski ◽  
Wolfgang Puntigam ◽  
Martin Kozek ◽  
Josef Hager
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Model ◽  
Transfer Model ◽  
Thermal Simulations
Sign in / Sign up

Export Citation Format

Share Document