scholarly journals Electrostatic MEMS Vibration Energy Harvesters inside of Tire Treads

Sensors ◽  
2019 ◽  
Vol 19 (4) ◽  
pp. 890 ◽  
Author(s):  
Yasuyuki Naito ◽  
Keisuke Uenishi
Keyword(s):  
Output Power ◽  
High Efficiency ◽  
Vibration Energy ◽  
Sinusoidal Vibration ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Electrostatic Mems ◽  
Output Electrode ◽  
Harvest Impact ◽  
Impact Vibration

An electret electrostatic MEMS vibration energy harvester for tire sensors mounted inside of the tire tread is reported. The device was designed so as to linearly change an electrostatic capacitance between the corrugated electret and output electrode according to the displacement of the proof mass. The electromechanical linearity was effective at reducing the power loss. The output power reached 495 μW under sinusoidal vibration despite the footprint size being as small as 1 cm2. Under impact vibration inside of the tire tread, the output power reached 60 μW at a traveling speed of 60 km/h. It was revealed that a higher mechanical resonance frequency of the harvester adjusted within the frequency band of a low-power spectral density of impact vibration acceleration was effective for high efficiency harvest impact vibration energy.

Modelling of Mechanical Nonlinearity in an Electromagnetic Vibration Energy Harvester Using a Forced Duffing Equation

2012 ◽  
Author(s):  
S. D. Moss ◽  
L. A. Vandewater ◽  
S. C. Galea
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Duffing Oscillator ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Homotopy Analysis ◽  
Wire Coil

This work reports on the modelling and experimental validation of a bi-axial vibration energy harvesting approach that uses a permanent-magnet/ball-bearing arrangement and a wire-coil transducer. The harvester’s behaviour is modelled using a forced Duffing oscillator, and the primary first order steady state resonant solutions are found using the homotopy analysis method (or HAM). Solutions found are shown to compare well with measured bearing displacements and harvested output power, and are used to predict the wideband frequency response of this type of vibration energy harvester. A prototype harvesting arrangement produced a maximum output power of 12.9 mW from a 12 Hz, 500 milli-g (or 4.9 m/s2) rms excitation.

scholarly journals Dynamic Modeling and Structural Optimization of a Bistable Electromagnetic Vibration Energy Harvester

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2410 ◽  
Author(s):  
Bei Zhang ◽  
Qichang Zhang ◽  
Wei Wang ◽  
Jianxin Han ◽  
Xiaoli Tang ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Electromagnetic Vibration ◽  
Magnetic Spring ◽  
Element Simulation ◽  
Nonlinear Galerkin Method ◽  
Simulation And Experiment ◽  
The Mathematical Model

A novel bistable electromagnetic vibration energy harvester (BEMH) is constructed and optimized in this study, based on a nonlinear system consisting mainly of a flexible membrane and a magnetic spring. A large-amplitude transverse vibration equation of the system is established with the general nonlinear geometry and magnetic force. Firstly, the mathematical model, considering the higher-order nonlinearities given by nonlinear Galerkin method, is applied to a membrane with a co-axial magnet mass and magnetic spring. Secondly, the steady vibration response of the membrane subjected to a harmonic base motion is obtained, and then the output power considering electromagnetic effect is analytically derived. On this basis, a parametric study in a broad frequency domain has been achieved for the BEMH with different radius ratios and membrane thicknesses. It is demonstrated that model predictions are both in close agreement with results from the finite element simulation and experiment data. Finally, the proposed efficient solution method is used to obtain an optimizing strategy for the design of multi-stable energy harvesters with the similar flexible structure.

scholarly journals Output Power of Piezoelectric MEMS Vibration Energy Harvesters Under Random Oscillation

2019 ◽  
Vol 1407 ◽  
pp. 012082
Author(s):  
S Murakami ◽  
T Yoshimura ◽  
M Aramaki ◽  
Y Kanaoka ◽  
K Tsuda ◽  
...  
Keyword(s):  
Output Power ◽  
Vibration Energy ◽  
Random Oscillation ◽  
Energy Harvesters ◽  
Piezoelectric Mems

On Mathematical Modeling of Piezoelectric Energy Harvesters

2014 ◽  
Vol 953-954 ◽  
pp. 655-658 ◽  
Author(s):  
Guang Qing Shang ◽  
Hong Bing Wang ◽  
Chun Hua Sun
Keyword(s):  
Mathematical Modeling ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Piezoelectric Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Piezoelectric Vibration

Energy harvesting system has become one of important areas of ​​research and develops rapidly. How to improve the performance of the piezoelectric vibration energy harvester is a key issue in engineering applications. There are many literature on piezoelectric energy harvesting. The paper places focus on summarizing these literature of mathematical modeling of piezoelectric energy harvesting, ranging from the linear to nonlinear, from early a single mechanical degree to piezoaeroelastic problems.

Heartbeat Energy Harvesting Using the Fan-Folded Piezoelectric Beam Geometry

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Mode Shapes ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam

A three dimensional piezoelectric vibration energy harvester is designed to generate electricity from heartbeat vibrations. The device consists of several bimorph piezoelectric beams stacked on top of each other. These horizontal bimorph beams are connected to each other by rigid vertical beams making a fan-folded geometry. One end of the design is clamped and the other end is free. One major problem in micro-scale piezoelectric energy harvesters is their high natural frequency. The same challenge is faced in development of a compact vibration energy harvester for the low frequency heartbeat vibrations. One way to decrease the natural frequency is to increase the length of the bimorph beam. This approach is not usually practical due to size limitations. By utilizing the fan-folded geometry, the natural frequency is decreased while the size constraints are observed. The required size limit of the energy harvester is 1 cm by 1 cm by 1 cm. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters are analytically derived. The electro-mechanical coupling has been included in the model for the piezoelectric beam. The design criteria for the device are discussed.

scholarly journals Power Supply Switch Circuit for Intermittent Energy Harvesting

Electronics ◽  
2019 ◽  
Vol 8 (12) ◽  
pp. 1446 ◽  
Author(s):  
Hyun Jun Jung ◽  
Saman Nezami ◽  
Soobum Lee
Keyword(s):  
Energy Harvesting ◽  
Power Management ◽  
Power Supply ◽  
High Efficiency ◽  
Operation Mode ◽  
Vibration Energy ◽  
Storage Device ◽  
Sleep Mode ◽  
Vibration Energy Harvesting ◽  
Vibration Energy Harvester

Energy harvesters generate power only when ambient energy is available, and power loss is significant when the harvester does not produce energy and its power management circuit is still turned on. This paper proposes a new high-efficiency power management circuit for intermittent vibration energy harvesting. The proposed circuit is unique in terms of autonomous power supply switch between harvester and storage device (battery), as well as self-start and control of the operation mode (between active and sleep modes). The self-start controller saves power during an inactive period and the impedance matching concept enables maximum power transfer to the storage device. The proposed circuit is prototyped and tested with an intermittent vibration energy harvester. Test results found that the daily energy consumption of the proposed circuit is smaller than that of the resistive matching circuit: 0.75 J less in sleep mode and 0.04 J less in active mode with self-start.

Temperature effects on output power of piezoelectric vibration energy harvesters

2011 ◽  
Vol 42 (8) ◽  
pp. 988-991 ◽  
Author(s):  
Seon-Bae Kim ◽  
Jung-Hyun Park ◽  
Hosang Ahn ◽  
Dan Liu ◽  
Dong-Joo Kim
Keyword(s):  
Output Power ◽  
Temperature Effects ◽  
Vibration Energy ◽  
Energy Harvesters ◽  
Piezoelectric Vibration
Sign in / Sign up

Export Citation Format

Share Document