scholarly journals RSM based Process Modeling and Optimization for Amylase Enzyme Production and its Desizing Potential

Enzyme technology is extensively touted as the way of the destiny for textile processing industry. Enzymes can be used safely in a wide selection of textile processes such as de-sizing, scouring, bleaching, dyeing, and finishing in textile processing. Recently, amylase enzyme is getting more important in textile industry for removal of starch. Amylase can be successfully applied at early pre-treatment stages, making a sturdy basis for the good finishing of fabrics. The present study was focused to isolate amylase producing bacteria and optimize the growth condition for maximizing amylase production using agro-industrial residues. In addition, immense important for RSM based optimization for the process parameters, pH, temperature, and agitation speed also given. Further, this study concentrated for determination of desizing potency of Denim by the amylase that produced at optimized condition.

2015 ◽  
Author(s):  
◽  
Martha Noro Chollom

The textile industry consumes large volumes of water and in turn produces substantial quantities of polluted effluents. Approximately 30% of reactive dyes used during the textile processing remain unfixed on fibres and are responsible for the colouration in effluents. Various conventional methods are being used to treat textile effluent. However, the disadvantage of these methods is that total colour removal is not achieved and chemical by-products are introduced from the use of chemicals. The water quality produced therefore does not meet the requirement for textile reuse. Membrane based processes provide interesting possibilities of separating hydrolysed dye stuff and dyeing auxiliaries, thereby reducing colouration and COD content. They can be employed to treat reactive dye bath effluent to recover the salts and water for the purpose of reuse. This study aimed at integrating membrane processes into the reactive dye bath of a textile industry. The objectives were to determine the quality of permeate produced in terms of removal of organics, ascertain its reusability for dyeing, investigate the production rate in terms of permeate fluxes and finally to investigate the cleanability and flux recovery of the membranes. Three effluent samples were chosen for this study based on the dyeing recipe; Light shade, Medium shade and Dark shade. Ultrafiltration (UF) and Nanofiltration (NF) membrane processes were employed to treat the reactive dye bath effluents to recover the salts and water. Investigations were conducted firstly with UF as a pre-treatment to NF. Secondly, evaluations were carried out on the performance of two types of NF membranes (SR90 and NF90) in terms of permeate quality and fluxes for the investigated samples. The effect of cleaning on membrane performance was done. A reusability test was carried out on the permeate samples for dyeing. It was found that the use of UF as a pre-treatment yielded an increase in permeate of 5–25% of the NF fluxes and 90% in organics reduction for all treated samples, hence increasing the water recovery. High rejection of ˃90% by NF90 for COD, TOC and colour were obtained for all the treated samples. SR90 rejection was 80–90% for colour and ˃90% for COD and TOC. Salt recovery for NF90 was 60–90% and for SR90 was 40–50%. The reusability tests carried out showed that permeate recycled from NF90 can be used for any section in the textile industry including the most critical such as dyeing on light shades, while that from SR90 can be used for dyeing dark shades only. It was then concluded that membrane based processes can be integrated into the dye bath of the textile process for the purpose of reuse, thereby saving on the cost of chemicals (salts), reducing fresh water usage and reducing the extent of final effluent treatment.


2017 ◽  
Vol 9 (1) ◽  
Author(s):  
Imam Setiadi ◽  
Dinda Rita K. Hartaja

Selection of the appropriate composition desalination units can be done with a variety of method approaches, one of the method is the Analytic Hierarchy Process. In determining the desalination unit with AHP method to consider is setting a goal, an alternative criteria and pairwise comparison. Research for the determination of the exact composition of the desalination unit in order to achieve sustainable drinking water suppy in coastal areas and small islands has been conducted. The results of the study are as follows, the energy demand of 50.83%, operator costs of 26.64%, maintenance costs of 14.13% and chemical requirement 8.4%. For an alternative composition desalination unit of RO 10 m3 / day is the best alternative composition with value of 59.61%, the composition of the next alternative is RO 20 m3/ day of 30.40% and the last alternative of the desalination unit composition is RO 120 m3/ day of 09.99%.Key words : Desalination, Mukti Stage Flash Composition, AHP


Kerntechnik ◽  
2008 ◽  
Vol 73 (3) ◽  
pp. 118-121
Author(s):  
T. Heinrich ◽  
L. Funke ◽  
M. Köhler ◽  
U.-K. Schkade ◽  
F. Ullrich ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document