Nanosecond-Pulsed Yb-Doped Fiber Laser at 978 nm Based on Diode Laser Modulation Technique

2016 ◽  
Vol 43 (8) ◽  
pp. 0801005
Author(s):  
周冠锐 Zhou Guanrui ◽  
师红星 Shi Hongxing ◽  
金东臣 Jin Dongchen ◽  
谭方舟 Tan Fangzhou ◽  
刘江 Liu Jiang ◽  
...  
Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 966
Author(s):  
Bogusława Żywicka ◽  
Zbigniew Rybak ◽  
Maciej Janeczek ◽  
Albert Czerski ◽  
Jolanta Bujok ◽  
...  

The authors would like to add the following sentence to the “Funding” section of their article [...]


2020 ◽  
Vol 126 (5) ◽  
Author(s):  
Bo Tao ◽  
Qingchun Lei ◽  
Jingfeng Ye ◽  
Zhenrong Zhang ◽  
Zhiyun Hu ◽  
...  

1998 ◽  
Vol 37 (15) ◽  
pp. 3276 ◽  
Author(s):  
Anthony L. Cook ◽  
Herbert D. Hendricks
Keyword(s):  

2021 ◽  
Vol 33 (3) ◽  
pp. 032018
Author(s):  
Hang Yang ◽  
Xiahui Tang ◽  
Chong Hu ◽  
Songjia Liu ◽  
Yuanchao Fan ◽  
...  

1996 ◽  
Vol 32 (1) ◽  
pp. 118-123 ◽  
Author(s):  
I.J. Booth ◽  
C.J. Mackechnie ◽  
B.F. Ventrudo
Keyword(s):  

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1167
Author(s):  
Bogusława Żywicka ◽  
Zbigniew Rybak ◽  
Maciej Janeczek ◽  
Albert Czerski ◽  
Jolanta Bujok ◽  
...  

Partial and total splenectomies are associated with a high risk of substantial blood loss. Lasers operating at wavelengths strongly absorbed by water have the potential to improve hemostasis and cut while providing a narrow zone of thermal damage. The aim of this study is to compare a thulium-doped fiber laser (TDFL) emitting a wavelength of 1940 nm and a diode laser (DL) operating at 1470 nm for spleen surgery in a pig model. A partial splenectomy and spleen incisions were made in 12 animals using the two laser devices. The hemostasis was evaluated visually during surgeries. Post-mortem and histopathological evaluations were done on days 0, 7, and 14 following surgery. Neither TDFL nor DL caused bleeding on day 0 or delayed bleeding. On day 14, pale streaks at the site of incision were slightly wider after cutting with DL than with TDFL. Histological analysis revealed a carbonized zone with exudation and a deeper zone of thermal tissue damage on day 0. The width of the thermal changes was 655.26 ± 107.70 μm for TDFL and 1413.37 ± 111.85 μm for DL. On day 7, a proliferation of fibroblasts and splenocytes was visible, as well as a formation of multinucleated giant cells adjacent to the residues of carbonization. The zone of thermal damage was broader for DL (1157.5 ± 262.77 μm) than for TDFL (682.22 ± 116.58 μm). On day 14, cutting sites were filled with connective and granulation tissues with the residues of carbonization. The zone of thermal damage was narrower for TDFL (761.65 ± 34.3 μm) than for DL (1609.82 ± 202.22 μm). Thus, both lasers are efficient in spleen surgery, providing good hemostasis. However, TDFL produces a narrower zone of thermal damage, which suggests its better efficiency for spleen surgery, especially when performing more precise procedures.


2006 ◽  
Vol 926 ◽  
Author(s):  
Ahsan Mian ◽  
Tonfiz Mahmood ◽  
Greg Auner ◽  
Reiner Witte ◽  
Hans Herfurth ◽  
...  

ABSTRACTThis paper is devoted to the laser irradiated joints between glass and polyimide. To facilitate bonding between them, a thin titanium film with a thickness of approximately 0.2 μm was deposited on glass wafers using the physical vapor deposition (PVD) process. Two sets of samples were fabricated where the bonds were created using diode and fiber lasers. The samples were subjected to tension using a microtester for bond strength measurements. The failure strengths of the bonds generated using fiber laser are quite consistent, while a wide variation of failure strengths are observed for the bonds generated with diode laser. Few untested samples were sectioned and the microstructures near the bond areas were studied using an optical microscope. The images revealed the presence of a sharp crack in the glass substrate near the bond generated with the diode laser. However, no such crack was observed in the samples made using fiber laser. To investigate further the reasons behind such discrepancy in bond quality, three-dimensional uncoupled finite element analysis (FEA) was conducted for both types of samples. The transient heat diffusion-based FEA model utilizes the laser power intensity distribution as a time dependent heat source to calculate the temperature distribution within the substrates as a function of time.


Sign in / Sign up

Export Citation Format

Share Document