scholarly journals A Review on Heat Transfer Enhancement of Solar Air Heater Using Various Artificial Roughed Geometries

2021 ◽  
Vol 89 (1) ◽  
pp. 92-133
Author(s):  
Sudharani Panda ◽  
Rakesh Kumar
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Heated Surface ◽  
Cost Effective ◽  
Solar Air Heater ◽  
Artificial Roughness ◽  
Air Heater

Solar air heater acts as one of the important components in utilization of solar energy. The air heater absorbs the irradiance and converts it into heat energy at the absorbing surface. The thermal energy is further use in heating flowing air through the duct. Solar air heaters are cost effective as well as simple in design. Solar air heater can be used in space heating, timber seasoning and agricultural drying. In spite of all these advantages the solar air heater has certain challenges such as the air has low heat transfer coefficient. The heat transfer rate from the heated absorber surface to the air is low. Hence in order to enhance the heat transfer coefficient the surface area either increases or the flow made to be turbulent. In order to do so the artificial roughened element must be incorporated on the heated surface. The use of artificial roughness is considered as an effective technique to enhance the heat transfer rate of fluid flowing through the duct of solar air heater. The heat transfer and friction characteristics of number of roughness geometries incorporated solar air heater have been investigated. In this paper an attempt has been made to review on element geometries used as artificial roughness in solar air heater in order to improve thermal and thermo hydraulic performance of solar air heater ducts.

Use of artificial roughness to enhance heat transfer in solar air heaters – a review

2010 ◽  
Vol 21 (1) ◽  
pp. 35-51 ◽  
Author(s):  
Thakur Sanjay Kumar ◽  
N.S. Thakur ◽  
Anoop Kumar ◽  
Vijay Mittal
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Hydraulic Performance ◽  
Solar Air Heater ◽  
Artificial Roughness ◽  
Transfer Enhancement ◽  
Air Heater ◽  
Roughness Elements

Improvement in the thermo hydraulic performance of a solar air heater can be done by enhancing the heat transfer. In general, heat transfer enhancement techniques are divided into two groups: active and passive techniques. Providing an artificial roughness on a heat transferring surface is an effective passive heat transfer technique to enhance the rate of heat transfer to fluid flow. In this paper, reviews of various artificial roughness elements used as passive heat transfer techniques, in order to improve thermo hydraulic performance of a solar air heater, is done. The objective of this paper is to review various studies, in which different artificial roughness elements are used to enhance the heat transfer rate with little penalty of friction. Correlations developed by various researchers with the help of experimental results for heat transfer and friction factor for solar air heater ducts by taking different roughened surfaces geometries are given in tabular form. These correlations are used to predict the thermo hydraulic performance of solar air heaters having roughened ducts. The objective is to provide a detailed review on heat transfer enhancement by using an artificial roughness technique. This paper will be very helpful for the researchers who are researching new artificial roughness for solar air heater ducts to enhance the heat transfer rate and comparing with artificial roughness already studied by various researchers.

Investigation of Ethylene Glycol Heat Transfer Coefficient Trough Double Pipe and Coil Heat Exchanger

2021 ◽  
Vol 874 ◽  
pp. 165-170
Author(s):  
Sri Wuryanti ◽  
Tina Mulya Gantina ◽  
Indriyani
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Ethylene Glycol ◽  
Transfer Coefficient ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Test System ◽  
Double Pipe ◽  
The Heat Transfer Coefficient ◽  
Outer Pipe

The research objective is to assemble a convection test system which acts as a heat exchanger (HE) and test its applicability using ethylene glycol. A Double Pipe (DP)-type HE consists of an inner pipe surrounded by an outer pipe (annulus) whereas a Coil-type HE composed of a coil surrounded by an outer pipe. Water flows through the outer pipe in both types of HE, while ethylene glycol flows through the inner piper or coil. HE in combination with other components (such as) forms a convection test system. The applicability of the system was tested to determine the heat transfer coefficient of ethylene glycol in a DP-type and Coil-type HEs. After that, the heat transfer rate was calculated and compared. The results show that the heat transfer coefficient in the DP-type HE is the lowest at 12.2 W/m2 oC and the highest at 26.8 W/m2 oC; and the corresponding heat transfer rate is the lowest at 8.3 W and the highest is 56.3 W. In comparison, for Coil-type HE, the lowest heat transfer coefficient is 38.9 W/m2 oC and the highest is 66.2 W/m2 oC which correspond to the heat transfer rate 19.9 W at the lowest and 225 W at the highest.

scholarly journals Enhanced Solar Air Heaters For Crop Drying

2021 ◽  
pp. 1-5
Author(s):  
Kamlesh Sahu ◽  
◽  
Gyaneshwar Sanodiya ◽  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Roughness Element ◽  
Air Flow ◽  
Thermal Capacity ◽  
Solar Air Heater ◽  
Artificial Roughness ◽  
Transfer Coefficients ◽  
Absorber Plate

Solar air heaters are placed on farms to provide heat for the drying of grain and crop harvesting and harvesting. The results of the thermal study showed that solar air heaters are capable of providing a sufficient increase in air temperature under the majority of crop drying circumstances studied. The restricted thermal capacity of air, as well as the low heat transfer coefficient between the absorber plate and the air flow via the ducting system, both contribute to the overall thermal efficiency of solar air heaters. Solar air heaters must be more efficient in order to be more affordable. This may be accomplished by increasing the heat transfer coefficient between the absorber plate and the air flow passing through the duct. More heat transfer coefficients can be increased by using either active or passive approaches. In most situations, it may be cost-effective to use solar air heaters and incorporate artificial roughness on the absorber plate. The rate of heat transmission from the solar air heater’s duct to the fluid flow may be increased by creating artificial roughness on the surface of the duct. The study focused on several roughness element geometries for solar air heater ducts, and the results indicated that there is a link between the two. This paper attempts to find ways to artificially increase the heat transfer capacity of solar air heaters’ ducts by using element geometries which have been utilised in solar air heaters’ heat transfer devices.

Sign in / Sign up

Export Citation Format

Share Document