Experiment and Numerical Simulation of Cavitation Performance for Centrifugal Pump with Inlet Guide Vane

2010 ◽  
Vol 46 (18) ◽  
pp. 177 ◽  
Author(s):  
Lei TAN
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Guide Vane ◽  
Inlet Guide Vane ◽  
Cavitation Performance

Hydraulic Design of Inlet Guide Vane and its Full Flow Passage Numerical Simulation on Centrifugal Pump

2014 ◽  
Author(s):  
Hucan Hou ◽  
Yongxue Zhang ◽  
Zhenlin Li ◽  
Xin Zhou ◽  
Zizhe Wang
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Guide Vane ◽  
Hydraulic Performance ◽  
Design Flow ◽  
Inlet Guide Vane ◽  
Hydraulic Efficiency ◽  
Flow Passage ◽  
Setting Angle ◽  
Hydraulic Design

In order to effectively improve hydraulic performance of centrifugal pump on off-conditions, the hydraulic design of inlet guide vane (IGV) was completed by adopting two dimensional theory in-house code based on one kind of IS series of centrifugal pump, which can achieve pre-whirl regulation of centrifugal pump. During design process the trailing edge of vane is assumed as equal velocity moment condition, and the distribution of vane setting angle along meridional streamline is also given as a quartic function firstly, the camber line is then drawn by point-by-point integration method and thickened at both sides along circumferential direction. With local vortex dynamics diagnosis theory, the optimal improvement of vane space shape can be finished by adjusting the design parameters of vane setting angle distribution coefficient ap. The full flow passage numerical simulations of centrifugal pump with IGV device are completed to analyze the influence of pre-whirl regulation on hydraulic performance of centrifugal pump under various pre-whirl angles. The results show that the pre-whirl regulation can improve the hydraulic performance of centrifugal pump on off-conditions. Under the positive pre-whirl regulation conditions, the best efficient point shift to small flow rate zone, and under the negative pre-whirl regulation conditions it moves to large flow rate zone. Compared with the pump without IGV device at the same flow rate condition of 0.8Q (Q the design flow rate), the hydraulic efficiency of centrifugal pump with IGV device improves obviously and reaches up to 1.43%. Meanwhile compared with that installed with the straight vanes designed based on the traditional theory, the inner flow field of centrifugal pump with the designed vanes improves and the overall hydraulic efficiency of centrifugal pump is somewhat increased.

scholarly journals The Effect of Inlet Swirl on the Rotordynamic Shroud Forces in a Centrifugal Pump

1992 ◽  
Author(s):  
A. Guinzburg ◽  
C. E. Brennen ◽  
A. J. Acosta ◽  
T. K. Caughey
Keyword(s):  
Centrifugal Pump ◽  
Guide Vane ◽  
Tangential Force ◽  
Inlet Guide Vane ◽  
Fluid Forces ◽  
Leakage Flows ◽  
Leakage Path ◽  
Inlet Swirl ◽  
Rotating Impeller ◽  
Rotordynamic Forces

The role played by fluid forces in determining the rotordynamic stability of a centrifugal pump is gaining increasing attention. The present research investigates the contributions to the rotordynamic forces from the discharge-to-suction leakage flows between the front shroud of the rotating impeller and the stationary pump casing. In particular, the dependency of the rotordynamic characteristics of leakage flows on the swirl at the inlet to the leakage path was examined. An inlet guide vane was designed for the experiment so that swirl could be introduced at the leakage flow inlet. The data demonstrates substantial rotordynamic effects and a destabilizing tangential force for small positive whirl ratios; this force decreased with increasing flow rate. The effect of swirl on the rotordynamic forces was found to be destabilizing.

Experiment and numerical simulation of cavitation performance for a double suction centrifugal pump

2015 ◽  
Vol 45 (10) ◽  
pp. 1111-1116
Author(s):  
GenQiQiGe MENG ◽  
PeiRu WEI ◽  
Wen JIAN ◽  
ShuLiang CAO ◽  
Lei TAN ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Cavitation Performance

scholarly journals Numerical Simulation Research on Radial Force of Centrifugal Pump with Guide Vanes

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Dongrong Meng ◽  
Ting Jiang ◽  
Hongling Deng ◽  
Gaoyang Hou
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Guide Vane ◽  
Radial Force ◽  
Flow State ◽  
Simulation Research ◽  
Flow Rates ◽  
Guide Vanes ◽  
Vector Distribution ◽  
Unsteady Numerical Simulation

To reveal the internal unsteady flow state of the guide vane centrifugal pump, in this paper, the standard SST k‐ω turbulent flow model is used for unsteady numerical simulation of the centrifugal pump. The characteristics of the flow field inside the centrifugal pump are analyzed, the resultant force and vector distribution of the radial force of the guide vane and impeller of the centrifugal pump under different flow rates are obtained, which were verified by experiments. The results show that the main reason of radial force of the impeller is the pressure asymmetry in each flow passage. The radial force will show periodic fluctuations due to the rotor-stator interference between the impeller and the guide vanes under different flow rates. The radial force on the impeller decreases gradually with the increase of the flow, the distribution is hexagonal or hexagonal shape, and the number of impeller blades is the same. The results can provide reference for the design of impeller and guide vane of centrifugal pump.

Inlet Guide Vane Performance of Centrifugal Blowers

1961 ◽  
Vol 83 (4) ◽  
pp. 371-378
Author(s):  
A. J. Stepanoff
Keyword(s):  
Centrifugal Pump ◽  
Guide Vane ◽  
Power Reduction ◽  
Single Stage ◽  
Experimental Results ◽  
Inlet Guide Vane ◽  
Pump Field ◽  
Guide Vanes ◽  
Inlet Guide Vanes ◽  
Specific Speed

The function and effectiveness of the inlet guide vanes to control the blower output and power requirements are examined. Calculated and experimental results of the power reduction by means of guide vanes are presented. The concept of the “Inlet Specific Speed” widely used in centrifugal pump field is discussed in application to the blowers. A method of estimating the performance of single-stage blowers for any position of the guide vanes is suggested. A “casing characteristic” is introduced for this purpose and its utility for the calculation of the impeller diameter for a reduction of the output is demonstrated. The performance of the inlet vanes of multistage blowers is reviewed.

Numerical Simulation of Cavitation Flow in a Centrifugal Pump

2013 ◽  
Vol 444-445 ◽  
pp. 509-516 ◽  
Author(s):  
Wei Guo Zhao ◽  
Xiao Xia He ◽  
Xiu Yong Wang ◽  
Yi Bin Li
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Cavitation Number ◽  
Suction Surface ◽  
Two Phase ◽  
Cavitation Performance ◽  
Practical Operation ◽  
And Performance ◽  
Pump Cavity ◽  
Homogeneous Mixture Model

Based on two phase homogeneous mixture model, numerical simulation of the cavitating flow was performed on a centrifugal pump. Cavity shapes and performance of the pump in variable cavitation numbers were obtained. Numerical results show that the numerical method can be used to predict the cavitation performance of centrifugal pump; the incipient cavitation number is predicted, and the cavity shape is similar with the experiment; cavitation usually appears in the suction surface of the blade and locates in the inlet side, and becomes longer to the outlet direction with lower cavitation number; when the cavitation number is relatively higher, cavitating region locates in the inlet area of the blade and is relatively stable, while develops and separates when cavitation number becomes lower; when the cavitation number equals to the incipient cavitation number, performance of the centrifugal pump has no change almost, only when cavitation number reduces to some extent, the head decreases abruptly and also the efficiency, which means the pump operates in a bad condition and this condition should be avoided in the practical operation.

scholarly journals The Effect of Inlet Swirl on the Rotordynamic Shroud Forces in a Centrifugal Pump

1993 ◽  
Vol 115 (2) ◽  
pp. 287-293 ◽  
Author(s):  
A. Guinzburg ◽  
C. E. Brennen ◽  
A. J. Acosta ◽  
T. K. Caughey
Keyword(s):  
Centrifugal Pump ◽  
Guide Vane ◽  
Tangential Force ◽  
Inlet Guide Vane ◽  
Fluid Forces ◽  
Leakage Flows ◽  
Leakage Path ◽  
Inlet Swirl ◽  
Rotating Impeller ◽  
Rotordynamic Forces

The role played by fluid forces in determining the rotordynamic stability of a centrifugal pump is gaining increasing attention. The present research investigates the contributions to the rotordynamic forces from the discharge-to-suction leakage flows between the front shroud of the rotating impeller and the stationary pump casing. In particular, the dependency of the rotordynamic characteristics of leakage flows on the swirl at the inlet to the leakage path was examined. An inlet guide vane was designed for the experiment so that swirl could be introduced at the leakage flow inlet. The data demonstrate substantial rotordynamic effects and a destabilizing tangential force for small positive whirl ratios; this force decreased with increasing flow rate. The effect of swirl on the rotordynamic forces was found to be destabilizing.

Experimental and numerical analysis of the unsteady influence of the inlet guide vanes on cavitation performance of an axial pump

2018 ◽  
Vol 233 (11) ◽  
pp. 3816-3826 ◽  
Author(s):  
Zhiwei Guo ◽  
Jingye Pan ◽  
Zhongdong Qian ◽  
Bin Ji
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Computational Fluid Dynamics ◽  
Guide Vane ◽  
Inlet Guide Vane ◽  
Guide Vanes ◽  
Inlet Guide Vanes ◽  
Cavitation Performance ◽  
Axial Pump ◽  
Simulation Results

The effect of the inlet guide vanes on cavitation performance of an axial pump is investigated to assess the mechanism for cavitation in pumps and improve their cavitation performance. The effect of inlet guide vane angles on cavitation performance was assessed experimentally, and computational fluid dynamics was used to analyze the inner flow field of the axial pump and to probe the cavitation mechanism. The simulation results agree qualitatively with the experimental data, showing that cavitation performance is improved with positive inlet guide vane angles but hampered with negative ones. The cavitation performance itself is controlled by the cavitation volume, which first expands circumferentially when the net positive suction head decreases from a certain large value and then develops toward the axis radially after the net positive suction head reaches a certain value. This is when the cavitation performance deteriorates. Comparing cavitation volume for the critical net positive suction head as determined by two different methods, the method based on efficiency drop (NPSHeff.,1%) is found to be more suitable than that based on head drop (NPSHhead.,3%). Furthermore, the distribution of swirl is shown to be closely related to the distribution of cavitation, a feature that may be used to predict cavitation along the impeller.

Sign in / Sign up

Export Citation Format

Share Document