The Study of TiCN Coating Based on Vacuum Arc Ion Plating and its Performance

2012 ◽  
Vol 187 ◽  
pp. 255-259
Author(s):  
Li Jing Zou
Keyword(s):  
Technology Development ◽  
Development Trend ◽  
Hard Coatings ◽  
Vacuum Arc ◽  
Application Development ◽  
Preparation Methods ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Ticn Coating ◽  
The Impact

This article provides an overview of the basic properties of the TiCN hard film, preparation methods, influencing factors, and application development trend. Magnetron sputter ion plating, radiofrequency sputtering method and multi-arc ion plating three coating preparation techniques are introduced. In this paper, with the coating by multi-arc ion plating method as the study object, an overview of the impact of C and N flow to its structure, as well as temperature, coating thickness, the pulse bias, the arc current to its performance is provided. Compared to other hard coatings, the improvement in its performance is showed and the future direction of technology development of TiCN is briefly discussed.

High vacuum arc ion plating Cr films: Self-ion bombarding effect and oxidation behavior

2021 ◽  
pp. 109476
Author(s):  
Jiaojiao Wu ◽  
Mingli Shen ◽  
Ming Hu ◽  
Cean Guo ◽  
Qiang Li ◽  
...  
Keyword(s):  
Oxidation Behavior ◽  
High Vacuum ◽  
Vacuum Arc ◽  
Arc Ion Plating ◽  
Ion Plating

Contact Failure Analysis of Nitrided 32Cr2MoV Coated with TiN by Multi-Arc Ion Plating

2008 ◽  
Vol 373-374 ◽  
pp. 576-579
Author(s):  
Hui Li ◽  
H.B. Xu ◽  
Jin Zhang
Keyword(s):  
Contact Fatigue ◽  
Hard Coatings ◽  
Tin Coating ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Matrix Surface ◽  
Failure Properties ◽  
Coated Surface ◽  
Primary Type ◽  
Contact Failure

In this paper, TiN coating was deposited onto the nitrided 32Cr2MoVA by multi arc ion plating and proceeded line contact fatigue experiment to investigate the influence of hard coatings on the contact failure properties of nitriding steel. The results of experiment show that pitting is primary type of contact fatigue failure for TiN coated 32Cr2MoV and the pits on the TiN coated surface are shallower and smaller than that of the nitrided 32Cr2MoV. After TiN coating produce crisping and desquamation under higher contact fatigue loads, the exposed matrix surface begin to bear the contact load. The superficial microstructure of TiN coated 32Cr2MoV was more fine, and content of nitrides were higher than that of the nitrided, which insured the distribution of hardness gradient of subsurface was more rational than that of nitrided 32Cr2MoV. The contact fatigue strength of TiN coated 32Cr2MoV is greater about 200MPa than that of the nitrided 32Cr2MoV.

Effect of Cu addition on properties of Ti-Al-Si-N nanocomposite films deposited by cathodic vacuum arc ion plating

2012 ◽  
Vol 206 (11-12) ◽  
pp. 2947-2953 ◽  
Author(s):  
J. Shi ◽  
A. Kumar ◽  
L. Zhang ◽  
X. Jiang ◽  
Z.L. Pei ◽  
...  
Keyword(s):  
Nanocomposite Films ◽  
Vacuum Arc ◽  
Arc Ion Plating ◽  
Ion Plating

Application of a novel vacuum-arc ion-plating technology for the design of advanced wear resistant coatings

2001 ◽  
Vol 138 (1) ◽  
pp. 71-76 ◽  
Author(s):  
A.N. Panckow ◽  
J. Steffenhagen ◽  
B. Wegener ◽  
L. Dübner ◽  
F. Lierath
Keyword(s):  
Vacuum Arc ◽  
Wear Resistant ◽  
Arc Ion Plating ◽  
Wear Resistant Coatings ◽  
Ion Plating

Properties of TiAl/TiAlN/TiAlCN Films Deposited by Arc Ion Plating on GCr15 Rings

2014 ◽  
Vol 789 ◽  
pp. 449-454 ◽  
Author(s):  
Li Jun Yang ◽  
Ze Hui Zhang ◽  
Xin An Dang ◽  
Lin Li
Keyword(s):  
Wear Resistance ◽  
Vapor Deposition ◽  
Pulsed Laser ◽  
Chemical Vapor ◽  
Laser Deposition ◽  
Vacuum Arc ◽  
Large Area ◽  
Arc Ion Plating ◽  
Ion Plating ◽  
Tin Film

Ring is one of the major textile spinning machine consumable part, it has an important influence on yarn quality and cost. Ring of domestic cotton spinning enterprises generally has poor hardness, bad accuracy, not durable and difficult to guarantee the quality of the yarn, foreign ring has excellent performance, but it is too expensive, so it is difficult to widely used in China[1]. Vacuum arc ion plating technology has a wide range of applications in the aerospace, automobile, mold, tool, electronics and other fields [2-3]. TiN film which is prepared by arc ion plating technology has been widely used because of the TiN film has poor oxidation resistance and wear resistance at high temperatures, so the ternary films are developed on TiN film, such as TiAlN [4], TiCN etc. Traveller circle in the ring on the slide to produce large amounts of heat, it makes the ring surface temperature reach 400°C. When higher than 400°C, the TiCN film failure, therefore, ring should not be plated on the TiCN films. While TiAlN film oxidation temperature reaches 800°C. In HSS twist drill, depositing of TiAlN film can improve the service life more than four times [5]. Studies [6-8] have found that using pulsed laser deposition and chemical vapor deposition technique to prepare TiAlCN film, its wear resistance, high temperature stability is better. Pulsed laser deposition is mainly used in laboratory research. It is difficult to deposit a large area uniform film. Chemical vapor deposition of deposition rate is less than the arc ion plating, and produces lots of waste gas, leading to the environment is polluted. Arc ion plating technology can deposit the uniform films of large area with high deposition rate and deposition with no environmental pollution, therefore, this study, by means of vacuum arc ion plating technology to prepare high-precision, long-life and low-cost domestic cotton spinning ring. In order to obtain the best film process parameters, the performance of film is investigated at different bias and arc current.

Sign in / Sign up

Export Citation Format

Share Document