Study on Characteristics of Ultrasonic Descaling and Heat Transfer Enhancement in Sewage Source Heat Pump System

2014 ◽  
Vol 525 ◽  
pp. 603-606
Author(s):  
Jian Feng Qian ◽  
Ya Yuan Liu ◽  
Ying Xu ◽  
Yan Kun Tan
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Transfer Enhancement ◽  
Heat Pump ◽  
Enhancement Effect ◽  
Transfer Enhancement ◽  
Pump System ◽  
Heat Pump System ◽  
Term Operation ◽  
Sewage Source

sewage heat exchanger is important to collect heat energy in sewage source heat pump system. Heat transfer enhancement effect is not obvious while the chemical methods and manual cleaning is applying to remove the heat exchangers fouling in the long-term operation. Here sets an ultrasonic incrustation removal physical model in heat exchanger structure to antiscaling and descaling simultaneously. The acoustic cavitation technology can be used in sewage source heat pump systems for the experimental results and decontamination rate reaches 50%.

Characteristics Study of Sewage Source Heat Pump System Based on Heat Transfer Enhancement and Acoustic Cavitation Decontamination

2014 ◽  
Vol 665 ◽  
pp. 607-610
Author(s):  
Jian Feng Qian ◽  
Ya Yuan Liu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Pump ◽  
Treatment Time ◽  
Acoustic Cavitation ◽  
Ultrasonic Cavitation ◽  
Transfer Enhancement ◽  
Pump System ◽  
Heat Pump System ◽  
Sewage Source

Put forward an application of ultrasonic cavitation technology of the sewage source heat pump system to solve the problem of controlling pollution and emphatically discusses the principle of acoustic cavitation and the effect, to conduct a feasibility analysis of Anti-fouling in sewage source heat pump sewage side. Through analysis principle of ultrasonic cavitation and heat transfer enhancement for carrying the experiment, study the pattern of scaling in heat exchange tube for different velocity and viscosity, effect in flow rate on the ultrasonic cleaning wastewater, Effect in ultrasonic treatment time on the descaling result. Obtain that it can enhancement transfer for 48%.

Key Problem Analysis and Solution on Intake Water and Heat Transfer of Sewage-Source Heat Pump System

2014 ◽  
Vol 1070-1072 ◽  
pp. 1799-1802
Author(s):  
Hai Yang Bi ◽  
Yong Mao Shang ◽  
Xiang Hong Gu
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Pump ◽  
Waste Heat ◽  
Problem Analysis ◽  
Pump System ◽  
Heat Pump System ◽  
Technology Application ◽  
Tube Heat Exchanger ◽  
Sewage Source

Changing "high consumption energy, low temperature heat to the indoor, waste heat to the environment", and turning the HVAC harmoniously into the natural ecological cycle, conform to the trend of the development of ecological architecture. Heat pump technology is a way of HVAC energy saving the most practical. Although low heat and cold source of the city sewage is ideal, but the quality is very unstable, can not meet the operation requirements of heat exchange equipment. This paper analyzes the key problems of the sewage side in sewage source heat pump technology application in the present: hair dirt clog sewage heat exchanger; fouling in heat surface reduces the heat transfer performance, and results in large heat-transfer equipment in the practical application. According to the key problems of sewage side, this paper prevents hair clogged with large tube heat exchanger; reduces the fouling thermal resistance, and enhances heat transfer process using the heat exchanging technology of circulating fluidized bed.

scholarly journals Performance and Exergy Transfer Analysis of Heat Exchangers with Graphene Nanofluids in Seawater Source Marine Heat Pump System

Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1762 ◽  
Author(s):  
Zhe Wang ◽  
Fenghui Han ◽  
Yulong Ji ◽  
Wenhua Li
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Pump ◽  
Heat Exchangers ◽  
Transfer Model ◽  
Enhanced Heat Transfer ◽  
Pump System ◽  
Heat Pump System ◽  
Tube Heat Exchanger ◽  
Exergy Transfer

A marine seawater source heat pump is based on the relatively stable temperature of seawater, and uses it as the system’s cold and heat source to provide the ship with the necessary cold and heat energy. This technology is one of the important solutions to reduce ship energy consumption. Therefore, in this paper, the heat exchanger in the CO2 heat pump system with graphene nano-fluid refrigerant is experimentally studied, and the influence of related factors on its heat transfer enhancement performance is analyzed. First, the paper describes the transformation of the heat pump system experimental bench, the preparation of six different mass concentrations (0~1 wt.%) of graphene nanofluid and its thermophysical properties. Secondly, this paper defines graphene nanofluids as beneficiary fluids, the heat exchanger gains cold fluid heat exergy increase, and the consumption of hot fluid heat is heat exergy decrease. Based on the heat transfer efficiency and exergy efficiency of the heat exchanger, an exergy transfer model was established for a seawater source of tube heat exchanger. Finally, the article carried out a test of enhanced heat transfer of heat exchangers with different concentrations of graphene nanofluid refrigerants under simulated seawater constant temperature conditions and analyzed the test results using energy and an exergy transfer model. The results show that the enhanced heat transfer effect brought by the low concentration (0~0.1 wt.%) of graphene nanofluid is greater than the effect of its viscosity on the performance and has a good exergy transfer effectiveness. When the concentration of graphene nanofluid is too high, the resistance caused by the increase in viscosity will exceed the enhanced heat transfer gain brought by the nanofluid, which results in a significant decrease in the exergy transfer effectiveness.

Heat Transfer Enhancement Effect of Nanostructured Surface Made of Carbon Nanotube on SiC Ceramics

2013 ◽  
Author(s):  
Hiroki Noguchi
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Transfer Enhancement ◽  
Chemical Vapor ◽  
Enhancement Effect ◽  
Nanostructured Surface ◽  
Transfer Enhancement ◽  
Energy Agency ◽  
Nanostructured Surfaces ◽  
Surface Decomposition

The Japan Atomic Energy Agency (JAEA) has been conducting research and development on the thermo-chemical iodine–sulfur (IS) process, which is one of the most attractive water-splitting hydrogen production methods using the nuclear heat of a high-temperature gas-cooled reactor (HTGR). In researching this IS process, a silicon carbide (SiC) heat exchanger with good corrosion resistance was used in a corrosive situation in boiling sulfuric acid. With the aim of enhancing heat transfer in the SiC heat exchanger, a nanostructured surface made of carbon nanotubes (CNTs) was produced on a SiC substrate by surface decomposition. Two types of SiC, one produced by pressureless sintering (PLS-SiC) and one by chemical vapor deposition (CVD-SiC), were used as substrates. CNTs formed by the surface decomposition of SiC can vary depending on the crystal structure of the substrates. Additionally, in order to investigate surface wettability, nanostructured surfaces on the CVD-SiC with hydrophilicity and hydrophobicity were produced. The effects of heat transfer enhancement by the nanostructured surfaces were evaluated by a convective heat transfer test using de-ionized water. The nanostructured surface on the CVD-SiC with hydrophilicity was the only surface that showed any heat transfer enhancement. However, this enhancement was much smaller than those previously reported. The experiment showed that the small size of the nanopores influenced the heat transfer enhancement and that the wettability of the nanostructured surface was related to heat transfer enhancement.

Sign in / Sign up

Export Citation Format

Share Document