Detection Method of Optical Fiber Connector Internal Parts Based on Machine Vision

2014 ◽  
Vol 568-570 ◽  
pp. 483-488 ◽  
Author(s):  
Bao Hua Shi ◽  
Ya Hui Wei

Technology of machine vision is used to measure the inside and outside diameter and concentricity of the optical fiber connector internal parts without contact. The image is got by million-pixel industrial camera. Then the image gets pretreatment, such as, grayscale transformation, binarization, smoothing, etc. Appropriate detection threshold is found by the image analysis. The edge of parts is found by the circular probe method. Inside and outside diameter and concentricity of parts are obtained by using the edge of the data through the least squares method. Experiment of 6.4 mm diameter parts, absolute error is less than one pixel. The largest error is less than 0.05 mm compared with the manual measurements and can meet the measurement requirements.

2020 ◽  
pp. 000370282097751
Author(s):  
Xin Wang ◽  
Xia Chen

Many spectra have a polynomial-like baseline. Iterative polynomial fitting (IPF) is one of the most popular methods for baseline correction of these spectra. However, the baseline estimated by IPF may have substantially error when the spectrum contains significantly strong peaks or have strong peaks located at the endpoints. First, IPF uses temporary baseline estimated from the current spectrum to identify peak data points. If the current spectrum contains strong peaks, then the temporary baseline substantially deviates from the true baseline. Some good baseline data points of the spectrum might be mistakenly identified as peak data points and are artificially re-assigned with a low value. Second, if a strong peak is located at the endpoint of the spectrum, then the endpoint region of the estimated baseline might have significant error due to overfitting. This study proposes a search algorithm-based baseline correction method (SA) that aims to compress sample the raw spectrum to a dataset with small number of data points and then convert the peak removal process into solving a search problem in artificial intelligence (AI) to minimize an objective function by deleting peak data points. First, the raw spectrum is smoothened out by the moving average method to reduce noise and then divided into dozens of unequally spaced sections on the basis of Chebyshev nodes. Finally, the minimal points of each section are collected to form a dataset for peak removal through search algorithm. SA selects the mean absolute error (MAE) as the objective function because of its sensitivity to overfitting and rapid calculation. The baseline correction performance of SA is compared with those of three baseline correction methods: Lieber and Mahadevan–Jansen method, adaptive iteratively reweighted penalized least squares method, and improved asymmetric least squares method. Simulated and real FTIR and Raman spectra with polynomial-like baselines are employed in the experiments. Results show that for these spectra, the baseline estimated by SA has fewer error than those by the three other methods.


2021 ◽  
pp. 334-343
Author(s):  
Xinzhen Ren ◽  
Wenju Zhou ◽  
Xiaogang Gu ◽  
Qiang Liu

Symmetry ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1158
Author(s):  
Jiayan Chen ◽  
Limeng Jing ◽  
Tao Hong ◽  
Hui Liu ◽  
Adam Glowacz

To solve the problem that the elevator traction wheel slippage is difficult to detect quantitatively, a slippage detection method is proposed based on machine vision. The slip between the traction wheel and the wire rope will occur during the round-trip operation of the elevator, the displacement distance between the traction wheel and the wire rope in the circumferential direction is obtained through the image signal processing algorithm and related data analysis. First, the ROI (region of interest) of the collected original image is selected to reduce redundant information. Then, a nonlinear geometric transformation is carried out to transform the image into the target image with an equal object distance. Finally, the centroid method is used to obtain the slippage between the traction wheel and the wire rope. The field test results show that the absolute error of the system developed in this paper is 0.74 mm and the relative error is 2%, the extending uncertainty of the slip detection results is (33.8 ± 0.69) mm, the confidence probability is p = 0.95, and the degree of freedom is v = 8, which can meet accuracy requirements of elevator maintenance.


2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
M. Sandoval-Hernandez ◽  
H. Vazquez-Leal ◽  
L. Hernandez-Martinez ◽  
U. A. Filobello-Nino ◽  
V. M. Jimenez-Fernandez ◽  
...  

This article introduces two approximations that allow the evaluation of Fresnel integrals without the need for using numerical algorithms. These equations accomplish the characteristic of being continuous in the same interval as Fresnel. Both expressions have been determined applying the least squares method to suitable expressions. Accuracy of equations improves as x increases; as for small values of x, it is possible to achieve an absolute error less than 8×10-5. To probe the efficiency of the equations, two case studies are presented, both applied in the optics field. The first case is related to the semi-infinite opaque screen for Fresnel diffraction. In this case study Fresnel integrals are evaluated with the proposed equations to calculate the irradiance distribution and the Cornu spiral for diffraction computations of the Fresnel diffraction; obtained results show a good accuracy. The second case is related to the double aperture problem for Fresnel diffraction.


1980 ◽  
Vol 59 (9) ◽  
pp. 8
Author(s):  
D.E. Turnbull

2020 ◽  
Vol 1 (3) ◽  
Author(s):  
Maysam Abedi

The presented work examines application of an Augmented Iteratively Re-weighted and Refined Least Squares method (AIRRLS) to construct a 3D magnetic susceptibility property from potential field magnetic anomalies. This algorithm replaces an lp minimization problem by a sequence of weighted linear systems in which the retrieved magnetic susceptibility model is successively converged to an optimum solution, while the regularization parameter is the stopping iteration numbers. To avoid the natural tendency of causative magnetic sources to concentrate at shallow depth, a prior depth weighting function is incorporated in the original formulation of the objective function. The speed of lp minimization problem is increased by inserting a pre-conditioner conjugate gradient method (PCCG) to solve the central system of equation in cases of large scale magnetic field data. It is assumed that there is no remanent magnetization since this study focuses on inversion of a geological structure with low magnetic susceptibility property. The method is applied on a multi-source noise-corrupted synthetic magnetic field data to demonstrate its suitability for 3D inversion, and then is applied to a real data pertaining to a geologically plausible porphyry copper unit.  The real case study located in  Semnan province of  Iran  consists  of  an arc-shaped  porphyry  andesite  covered  by  sedimentary  units  which  may  have  potential  of  mineral  occurrences, especially  porphyry copper. It is demonstrated that such structure extends down at depth, and consequently exploratory drilling is highly recommended for acquiring more pieces of information about its potential for ore-bearing mineralization.


1984 ◽  
Vol 49 (4) ◽  
pp. 805-820
Author(s):  
Ján Klas

The accuracy of the least squares method in the isotope dilution analysis is studied using two models, viz a model of a two-parameter straight line and a model of a one-parameter straight line.The equations for the direct and the inverse isotope dilution methods are transformed into linear coordinates, and the intercept and slope of the two-parameter straight line and the slope of the one-parameter straight line are evaluated and treated.


Sign in / Sign up

Export Citation Format

Share Document