scholarly journals Green Strength Optimization in Metal Injection Molding Applicable with a Taguchi Method L9 (3)4

2015 ◽  
Vol 773-774 ◽  
pp. 115-117 ◽  
Author(s):  
N. Mustafa ◽  
Mohd Halim Irwan Ibrahim ◽  
Rosli Asmawi ◽  
Azriszul Mohd Amin ◽  
S.R. Masrol
Keyword(s):  
Injection Molding ◽  
Taguchi Method ◽  
Complex Geometry ◽  
Signal To Noise Ratio ◽  
Injection Pressure ◽  
Cost Effective ◽  
Metal Injection Molding ◽  
Injection Molding Process ◽  
Molding Process ◽  
Green Strength

Recently Metal injection molding is selected as a vital process in producing large amount of small part with complex geometry and intricate shape. This process is lead to solve cost effective issue in manufacturing fields. Feedstock composition behavior categorized as one of impact factor in determines the victories in metal injection molding process. Thus this paper is focused on optimizing the strength of green part by applied Taguchi Method L9 (34) as optimization tools during injection process. The composition of feedstock is 55% powder loading (PL) were injected by injection molding machine .Several injection parameter were optimized such as injection temperature (A), barrel temperature (B), injection pressure (C) and Speed (D) The results analyzed by using Signal to Noise Ratio (S/N ratio) terms. The highest green strength is A2, B2, C2, and D2

scholarly journals Study on Stability of a Novel Binder System Based on Palm Stearin in Metal Injection Moulding Application

2007 ◽  
Vol 4 (2) ◽  
pp. 1
Author(s):  
Muhammad Hussain Ismail ◽  
Norhamidi Muhamad ◽  
Aidah Jumahat ◽  
Istikamah Subuki ◽  
Mohd Afian Omar
Keyword(s):  
Injection Molding ◽  
Flow Characteristics ◽  
Injection Pressure ◽  
Palm Stearin ◽  
Steel Powder ◽  
Metal Injection Molding ◽  
Injection Molding Process ◽  
Binder System ◽  
Molding Process ◽  
Flow Activation Energy

Metal Injection Molding (MIM) is a wellestablished technology for manufacturing a variety of complex and small precision parts. In this paper, fundamental rheological characteristics of MIM feedstock using palm stearin are theoretically analyzed and presented. The feedstock consisted of gas atomized 316L stainless steel powder at three different particle size distributions and the binder system of palm stearin (PS) and polyethylene (PE). The powder loading used was 60vol % for all samples (monosize 16 µm, monosize 45 µm, and bimodal 16 µm + 45 µm) and the binder system of 40vol %(PS/PE = 40/60). The viscosity of MIM feedstock at different temperatures and shear rates was measured and evaluated. Results showed that, the feedstock containing palm stearin exhibited suitable rheological properties by increasing the fluidity of feedstock in MIM process. The rheological results also showed a pseudoplastic flow characteristics, which poses higher value of shear sensitivity (n) and lower value of flow activation energy (E), that are both favourable for injection molding process. The green parts were successfully injected and exhibited adequate strength for handling by optimizing the injection pressure and temperature.

Optimizing Injection Parameters of Kenaf Filler Polypropylene Composite by Taguchi Method

2017 ◽  
Vol 894 ◽  
pp. 81-84 ◽  
Author(s):  
Mohd Khairul Fadzly Md Radzi ◽  
Norhamidi Muhamad ◽  
Abu Bakar Sulong ◽  
Zakaria Razak
Keyword(s):  
Injection Molding ◽  
Taguchi Method ◽  
Process Condition ◽  
Injection Pressure ◽  
Poor Quality ◽  
Injection Molding Process ◽  
Molding Process ◽  
Injection Parameters ◽  
Pp Composites ◽  
Injection Temperature

Optimization of injection molding parameters provided a solution to achieve strength improvement of kenaf filler polypropylene composites. Since, molded polymers composites possibility being effected by machine parameters and other process condition that may cause poor quality of composites product. Thus in this study, composite of kenal filler reinforced with thermoplastic polypropylene (PP) were prepared using a sigma blade mixer, followed by an injection molding process. To determine the optimal processing of injection parameters, Taguchi method with L27 orthogonal array was used on statistical analysis of tensile properties of kenaf/PP composites. The results obtained the optimum parameters which were injection temperature 190°C, injection pressure 1300 bar, holding pressure 1900 bar and injection rate 20cm3/s. From the analysis of variance (ANOVA), both flow rate and injection temperature give highest contribution factor to the mechanical properties of the kenaf/PP composites.

scholarly journals Study on Stability of a Novel Binder System Based on Palm Stearin in Metal Injection Moulding Application

2007 ◽  
Vol 4 (2) ◽  
pp. 1 ◽  
Author(s):  
Muhammad Hussain Ismail ◽  
Norhamidi Muhamad ◽  
Aidah Jumahat ◽  
Istikamah Subuki ◽  
Mohd Afian Omar
Keyword(s):  
Injection Molding ◽  
Flow Characteristics ◽  
Injection Pressure ◽  
Palm Stearin ◽  
Steel Powder ◽  
Metal Injection Molding ◽  
Injection Molding Process ◽  
Binder System ◽  
Molding Process ◽  
Flow Activation Energy

Metal Injection Molding (MIM) is a wellestablished technology for manufacturing a variety of complex and small precision parts. In this paper, fundamental rheological characteristics of MIM feedstock using palm stearin are theoretically analyzed and presented. The feedstock consisted of gas atomized 316L stainless steel powder at three different particle size distributions and the binder system of palm stearin (PS) and polyethylene (PE). The powder loading used was 60vol % for all samples (monosize 16 µm, monosize 45 µm, and bimodal 16 µm + 45 µm) and the binder system of 40vol %(PS/PE = 40/60). The viscosity of MIM feedstock at different temperatures and shear rates was measured and evaluated. Results showed that, the feedstock containing palm stearin exhibited suitable rheological properties by increasing the fluidity of feedstock in MIM process. The rheological results also showed a pseudoplastic flow characteristics, which poses higher value of shear sensitivity (n) and lower value of flow activation energy (E), that are both favourable for injection molding process. The green parts were successfully injected and exhibited adequate strength for handling by optimizing the injection pressure and temperature.

Optimization of Micro Metal Injection Molding SS 316L for the Highest Green Strength by Using Taguchi Method

2011 ◽  
Vol 264-265 ◽  
pp. 135-140 ◽  
Author(s):  
Mohd Halim Irwan Ibrahim ◽  
Norhamidi Muhamad ◽  
Abu Bakar Sulong ◽  
Khairur Rijal Jamaludin ◽  
Nor Hafiez Mohamad Nor ◽  
...  
Keyword(s):  
Injection Molding ◽  
Taguchi Method ◽  
Injection Pressure ◽  
Rheological Characteristic ◽  
Mold Temperature ◽  
Metal Injection Molding ◽  
Small Scale ◽  
Injection Time ◽  
Green Strength ◽  
Injection Temperature

Micro metal injection molding which is a new develop technology has attract most researcher where it becomes among the promising method in powder metallurgy research to produce small-scale intricate part at an effective process and competitive cost for mass production. Due to highly stringent characteristics of micro MIM feedstock,the study has been emphasized in investigating the optimization of highest green strength which plays an important characteristic in determining the successful of micro MIM. Stainless steel SS 316L with D50 = 5.96μm was used with composite binder, which consists of PEG, PMMA and Stearic Acid. From rheological characteristic and highly significant parameter through screening experiment, feedstock with 61.5% with several injection parameters were optimized such as injection pressure(A), injection temperature(B), mold temperature(C), injection time(D) and holding time(E). Besides that, interaction effects between injection pressure, injection temperature and mold temperature were also considered to optimize in the Taguchi’s orthogonal array. Analysis of variance (ANOVA) in terms of signal-to-noise ratio (S/N-larger is better) for green strength was also presented in this paper. Result shows that interaction between injection temperature and mold temperature(BxC) give highest significant factor followed by interaction between injection pressure and injection temperature(AxB). Single factor that also contributes to significant optimization are mold temperature(C), injection time(D) and injection pressure(A). This study shows that Taguchi method would be among the best method to solve the problem with minimum number of trials.

Parameter Optimization towards Highest Micro MIM Density by Using Taguchi Method

2010 ◽  
Vol 443 ◽  
pp. 705-710 ◽  
Author(s):  
Mohd Halim Irwan Ibrahim ◽  
Norhamidi Muhamad ◽  
Abu Bakar Sulong ◽  
Khairur Rijal Jamaludin ◽  
Nor Hafiez Mohamad Nor ◽  
...  
Keyword(s):  
Taguchi Method ◽  
Signal To Noise Ratio ◽  
Injection Pressure ◽  
Mold Temperature ◽  
Metal Injection Molding ◽  
Small Scale ◽  
Injection Time ◽  
Green Strength ◽  
Minimum Number ◽  
Injection Temperature

Nowadays, micro metal injection molding has become among the promising method in powder metallurgy research to produce small-scale intricate part at an effective process and competitive cost for mass production. This paper investigated the optimization of highest green strength which plays an important characteristic in determining the successful of micro MIM. In this paper, stainless steel SS 316L with D50 = 5.96µm was used with composite binder, which consists of PEG (Polyethelena Glycol), PMMA (Polymethyl Methacrilate) and SA (Stearic Acid). Feedstock with 61.5% with several injection parameters were optimized which highly significant through screening experiment such as injection pressure(A), injection temperature(B), mold temperature(C), injection time(D) and holding time(E). Besides that, interaction effects between injection pressure, injection temperature and mold temperature were also considered to optimize in the Taguchi’s orthogonal array. Analysis of variance (ANOVA) in terms of signal-to-noise ratio (S/N-larger is better) for green density was also presented in this paper. Result shows that interaction between injection temperature and mold temperature(BxC) give highest significant factor followed by interaction between injection pressure and mold temperature(AxC). Single factor that also contributes to significant optimization are mold temperature(C) and injection time(D). This study shows that Taguchi method would be among the best method to solve the problem with minimum number of trials.

The Characterization and Flow Behavior of 316L Stainless Steel Feedstock for Micro Metal Injection Molding (μMIM)

2010 ◽  
Vol 44-47 ◽  
pp. 2872-2876
Author(s):  
Pei Li Haw ◽  
Norhamidi Muhamad ◽  
Hadi Murthadha
Keyword(s):  
Stainless Steel ◽  
Injection Molding ◽  
316L Stainless Steel ◽  
Flow Behavior ◽  
Palm Stearin ◽  
Metal Injection Molding ◽  
Injection Molding Process ◽  
Binder System ◽  
Molding Process ◽  
Rheological Characterization

The rheological behaviors of the Micro Metal Injection Molding feedstock are important for the stability of the feedstock during micro injection molding process and quality of the final micro-components. Homogeneous feedstocks are preferable for MIM process to ensure the dimensional consistency of molded components and prevent the defects of powder-binder separation or particle segregation. In this work, feedstocks with various formulations of 316L stainless steel and binder system were prepared by using Brabender Plastograph EC Plus mixer. The binder system comprises of palm stearin, polyethelene (PE) and stearic acid. In order to obtain the viscosity, activation energy, flow behavior and mold ability index, the rheological characterization of the feedstocks were investigated in numerous conditions by using Shimadzu 500-D capillary rheometer The study showed that all of the 316L stainless steel feedstocks are homogenous with pseudo-plastic behaviors.

Manufacturing and High Temperature Mechanical Properties of Inconel 713C by Using Metal Injection Molding

2012 ◽  
Vol 602-604 ◽  
pp. 627-630 ◽  
Author(s):  
Kyu Sik Kim ◽  
Kee Ahn Lee ◽  
Jong Ha Kim ◽  
Si Woo Park ◽  
Kyu Sang Cho
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Injection Molding ◽  
Room Temperature ◽  
Tensile Tests ◽  
Metal Injection Molding ◽  
Injection Molding Process ◽  
Molding Process ◽  
High Temperature Mechanical Properties ◽  
Inconel 713C

Inconel 713C alloy was tried to manufacture by using MIM(Metal Injection Molding) process. The high-temperature mechanical properties of MIMed Inconel 713C were also investigated. Processing defects such as pores and binders could be observed near the surface. Tensile tests were conducted from room temperature to 900°C. The result of tensile tests showed that this alloy had similar or somewhat higher strengths (YS: 734 MPa, UTS: 968 MPa, elongation: 7.16 % at room temperature) from RT to 700°C than those of conventional Inconel 713C alloys. Above 800°C, however, ultimate tensile strength decreased rapidly with increasing temperature (lower than casted Inconel 713C). Based on the observation of fractography, initial crack was found to have started near the surface defects and propagated rapidly. The superior mechanical properties of MIMed Inconel 713C could be obtained by optimizing the MIM process parameters.

Sign in / Sign up

Export Citation Format

Share Document