A Study on Fatigue Life Evaluation of Pressure Vessel Made of ASME SA240-316L Material Using Numerical Analysis

2019 ◽  
Vol 893 ◽  
pp. 1-5 ◽  
Author(s):  
Eui Soo Kim
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Pressure Vessel ◽  
Life Prediction ◽  
Pressure Vessels ◽  
Physical Damage ◽  
Element Analysis ◽  
Internal Damage ◽  
Life Evaluation ◽  
Fatigue Life Evaluation

Pressure vessels are subjected to repeated loads during use and charging, which can causefine physical damage even in the elastic region. If the load is repeated under stress conditions belowthe yield strength, internal damage accumulates. Fatigue life evaluation of the structure of thepressure vessel using finite element analysis (FEA) is used to evaluate the life cycle of the structuraldesign based on finite element method (FEM) technology. This technique is more advanced thanfatigue life prediction that uses relational equations. This study describes fatigue analysis to predictthe fatigue life of a pressure vessel using stress data obtained from FEA. The life prediction results areuseful for improving the component design at a very early development stage. The fatigue life of thepressure vessel is calculated for each node on the model, and cumulative damage theory is used tocalculate the fatigue life. Then, the fatigue life is calculated from this information using the FEanalysis software ADINA and the fatigue life calculation program WINLIFE.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

TTK Chitra tilting disc heart valve model TC2: An assessment of fatigue life and durability

2017 ◽  
Vol 231 (8) ◽  
pp. 758-765 ◽  
Author(s):  
NN Subhash ◽  
Adathala Rajeev ◽  
Sreedharan Sujesh ◽  
CV Muraleedharan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Fatigue Life ◽  
Heart Valve ◽  
Life Prediction ◽  
Heart Valves ◽  
Failure Modes ◽  
Fatigue Life Prediction ◽  
Element Analysis ◽  
Valve Model

Average age group of heart valve replacement in India and most of the Third World countries is below 30 years. Hence, the valve for such patients need to be designed to have a service life of 50 years or more which corresponds to 2000 million cycles of operation. The purpose of this study was to assess the structural performance of the TTK Chitra tilting disc heart valve model TC2 and thereby address its durability. The TC2 model tilting disc heart valves were assessed to evaluate the risks connected with potential structural failure modes. To be more specific, the studies covered the finite element analysis–based fatigue life prediction and accelerated durability testing of the tilting disc heart valves for nine different valve sizes. First, finite element analysis–based fatigue life prediction showed that all nine valve sizes were in the infinite life region. Second, accelerated durability test showed that all nine valve sizes remained functional for 400 million cycles under experimental conditions. The study ensures the continued function of TC2 model tilting disc heart valves over duration in excess of 50 years. The results imply that the TC2 model valve designs are structurally safe, reliable and durable.

Life Assessment of Turbine Components Through Experimental and Numerical Investigations

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Dianyin Hu ◽  
Rongqiao Wang ◽  
Guicang Hou
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Fatigue Life ◽  
Life Prediction ◽  
Life Assessment ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Creep Fatigue ◽  
Turbine Component ◽  
Good Agreement

A new lifetime criterion for withdrawal of turbine components from service is developed in this paper based on finite element (FE) analysis and experimental results. Finite element analysis is used to determine stresses in the turbine component during the imposed cyclic loads and analytically predict a fatigue life. Based on the finite element analysis, the critical section is then subjected to a creep-fatigue test, using three groups of full scale turbine components, attached to an actual turbine disc conducted at 750 °C. The experimental data and life prediction results were in good agreement. The creep-fatigue life of this type of turbine component at a 99.87% survival rate is 30 h.

Study on the Stress Concentration at the Round Corners of Flat Heads in Pressure Vessels Subjected to Internal Pressure

1996 ◽  
Vol 118 (4) ◽  
pp. 429-433
Author(s):  
H. Chen ◽  
J. Jin ◽  
J. Yu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Intensity ◽  
Stress Concentration ◽  
Internal Pressure ◽  
Pressure Vessel ◽  
Pressure Vessels ◽  
Stress Index ◽  
Element Analysis ◽  
Approximate Formulas

Results from finite element analysis were used to show that the stress index kσ and the nondimensionalized highly stressed hub length kh of a flat head with a round corner in a pressure vessel subjected to internal pressure are functions of three dimensionless parameters: λ ≡ h/dt, η ≡ t/d, and ρ ≡ r/t. Approximate formulas for estimating kσ and kh from λ, η, and ρ p are given. The formulas can be used for determining a suitable fillet radius for a flat head in order to reduce the fabricating cost and to keep the stress intensity at the fillet under an acceptable limit.

scholarly journals Design and finite element analysis of a fatigue life prediction for safe and economical machine shaft

2019 ◽  
Vol 8 (1) ◽  
pp. 105-111 ◽  
Author(s):  
Samuel O. Afolabi ◽  
Bankole I. Oladapo ◽  
Christianah O. Ijagbemi ◽  
Adeyinka O.M. Adeoye ◽  
Joseph F. Kayode
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Fatigue Life ◽  
Life Prediction ◽  
Fatigue Life Prediction ◽  
Element Analysis

Fracture Mechanics Fatigue Evaluation of a Flowline Clamp Connector Using Finite Element Modeling of a Crack

2019 ◽  
Author(s):  
Curtis Sifford ◽  
Ali Shirani
Keyword(s):  
Finite Element Analysis ◽  
Stress Intensity Factor ◽  
Finite Element ◽  
Fatigue Life ◽  
Stress Intensity ◽  
Fracture Mechanics ◽  
Intensity Factor ◽  
Pressure Vessel ◽  
Crack Tip ◽  
Element Analysis

Abstract This paper presents the application of the rules from ASME Section VIII, Division 3 of the ASME Boiler and Pressure Vessel Code for a fracture mechanics evaluation to determine the damage tolerance and fatigue life of a flowline clamp connector. The guidelines from API 579-1 / ASME FFS-1 Fitness-For-Service for the stress analysis of a crack-like flaw have been considered for this assessment. The crack tip is modeled using a refined mesh around the crack tip that is referred to as a focused mesh approach in API 579-1 / ASME FFS-1. The driving force method is used as an alternative to the failure assessment diagram method to account for the influence of crack tip plasticity. The J integral is determined using elastic-plastic finite element analysis and converted to an equivalent stress intensity factor to be compared to the fracture toughness of the material. The fatigue life is calculated using the Paris Law equation and the stress intensity factor calculated from the finite element analysis. The allowable number of design cycles is determined using the safety factors required from Division 3 of the ASME Pressure Vessel Code.

Fracture Mechanics Fatigue Evaluation of a Flowline Clamp Connector Using Finite Element Modeling of a Crack

2018 ◽  
Author(s):  
Curtis Sifford ◽  
Ali Shirani
Keyword(s):  
Finite Element Analysis ◽  
Stress Intensity Factor ◽  
Finite Element ◽  
Fatigue Life ◽  
Stress Intensity ◽  
Fracture Mechanics ◽  
Intensity Factor ◽  
Pressure Vessel ◽  
Crack Tip ◽  
Element Analysis

This paper presents the application of the rules from ASME Section VIII, Division 3 of the ASME Boiler and Pressure Vessel Code for a fracture mechanics evaluation to determine the damage tolerance and fatigue life of a flowline clamp connector. The guidelines from API 579-1 / ASME FFS-1 Fitness-For-Service for the stress analysis of a crack-like flaw have been considered for this assessment. The crack tip is modeled using a refined mesh around the crack tip that is referred to as a focused mesh approach in API 579-1 / ASME FFS-1. The driving force method is used as an alternative to the failure assessment diagram method to account for the influence of crack tip plasticity. The J integral is determined using elastic-plastic finite element analysis and converted to an equivalent stress intensity factor to be compared to the fracture toughness of the material. The fatigue life is calculated using the Paris Law equation and the stress intensity factor calculated from the finite element analysis. The allowable number of design cycles is determined using the safety factors required from Division 3 of the ASME Pressure Vessel Code.

Sign in / Sign up

Export Citation Format

Share Document