Analysis and Numerical Simulation of Flow Field in Centrifugal Pump

2014 ◽  
Vol 1006-1007 ◽  
pp. 131-134
Author(s):  
Yi Jun Zhou ◽  
Hai Yang Xu ◽  
Wang Kan
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Centrifugal Pump ◽  
Static Pressure ◽  
Three Dimensional ◽  
Centrifugal Impeller ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Design And Optimization ◽  
Fluent Software

The inner flow field of centrifugal pump is complex and presents a characteristic of three-dimensional turbulence. Used Solidworks software to establish a three-dimensional model of the pump and impeller, completed the numerical simulation of centrifugal impeller flow field based on the turbulence model and Fluent software, obtained the static pressure and velocity distribution of flow field, provided basis for the design and optimization of the subsequent product.

Simulation of the Flow Parameters of the Multi-Microchannel Aerostatic Restrictor

2012 ◽  
Vol 241-244 ◽  
pp. 1278-1284
Author(s):  
Yu Bing Zhang ◽  
Cai Qin Li ◽  
Dong Sheng Li
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Film Thickness ◽  
Three Dimensional ◽  
Simulation Method ◽  
Gas Pressure ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Flow Parameters ◽  
Numerical Simulation Method

A numerical simulation method, FLUENT,has been selected to simulate the flow field parameters of the multi-microchannel aerostatic restrictor. Pressure, temperature and velocity distributions of the restrictor under different gas film thickness and gas pressure were got and compared. Used Pro / E to establish three-dimensional model of restrictor and imported it into GAMBIT for meshing, and then used FLUENT for simulation.

scholarly journals Research on Parametric Design of Hydraulic Retarder Based on Multi-Field Coupling of Heat, Fluid and Solid

2015 ◽  
Vol 9 (1) ◽  
pp. 58-64 ◽  
Author(s):  
Kuiyang Wang ◽  
Jinhua Tang ◽  
Guoqing Li
Keyword(s):  
Numerical Simulation ◽  
Parametric Design ◽  
Design Method ◽  
Three Dimensional ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Field Coupling ◽  
Sequential Coupling ◽  
Fluid Coupling ◽  
Hydraulic Retarder

In order to optimize the design method and improve the performance of hydraulic retarder, the numerical simulation of multi-field coupling of heat, fluid and solid is carried out to hydraulic retarder, based on the numerical computation and algorithm of heat-fluid coupling and fluid-solid coupling. The computation models of heat-fluid coupling and fluid-solid coupling of hydraulic retarder are created. The three dimensional model of hydraulic retarder is established based on CATIA software, and the whole flow passage model of hydraulic retarder is extracted on the basis of the three dimensional model established. Based on the CFD calculation and the finite element numerical simulation, the temperature field, stress field, deformation and stress state are analysised to hydraulic retarder in the state of whole filling when the rotate speed is 1600 r/min. In consideration of rotating centrifugal force, thermal stress and air exciting vibration force of blade surface, by using the sequential coupling method, the flow field characteristics of hydraulic retarder and dynamic characteristics of blade structure are analysised and researched based on multi-field coupling of heat, fluid and solid. These provide the theoretical foundation and references for parametric design of hydraulic retarder.

Three-Dimensional Numerical Analysis of Horizontal and Vertical Coalescence of Bubbles at Two Submerged Horizontal Orifices on the Wall

2019 ◽  
Author(s):  
Z. P. Li ◽  
L. Q. Sun ◽  
X. L. Yao ◽  
Y. Piao
Keyword(s):  
Numerical Simulation ◽  
Internal Pressure ◽  
Three Dimensional ◽  
Ventilation Rate ◽  
Smoothing Technique ◽  
Dimensional Model ◽  
Mesh Smoothing ◽  
Three Dimensional Model ◽  
Coalescence Time ◽  
Ventilation Rates

Abstract In the process of bubbling from two submerged adjacent orifices, bubbles coalescence becomes inevitable. But the study of the evolution and interaction of bubbles from submerged orifices is little, especially numerical simulation. In this paper, combined with mesh smoothing technique, mesh subdivision technique and the technique of axisymmetric coalescence and 3D coalescence, a three-dimensional model of bubbles coalescence at two submerged adjacent orifices on the wall is established by the boundary element method. Then, numerical simulations were carried out for horizontal and vertical coalescence before detachment. Finally, by changing the ventilation rate and the Froude number, the effects of different ventilation rates and buoyancy on the process of bubbles coalescence at two adjacent orifices were investigated. The results show that for horizontal coalescence, the effect of ventilation rate is more pronounced than buoyancy. As the ventilation rate increases or the influence of buoyancy is decreased, the amplitude of internal pressure fluctuation of the bubble decreases and the coalescence time decreases. For vertical coalescence, the effect of buoyancy is more pronounced than ventilation rate. With the influence of buoyancy is decreased, the vertical coalescence time is increased, the internal pressure of the bubble is decreased. The influence of ventilation rate is similar to that of horizontal coalescence.

Numerical simulation of three-dimensional airflow in a novel dual-feed rotor spinning box

2016 ◽  
Vol 88 (3) ◽  
pp. 237-253 ◽  
Author(s):  
Nicholus Tayari Akankwasa ◽  
Huiting Lin ◽  
Yuze Zhang ◽  
Jun Wang
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Three Dimensional ◽  
Internal Flow ◽  
Velocity Variation ◽  
Positive Pressure ◽  
Three Dimensional Model ◽  
Air Velocity ◽  
Rotor Spinning ◽  
Pressure Profiles

In order to regulate turbulence strength and determine airflow characteristics in a new dual-feed rotor spinning unit, the internal flow field is investigated. A computational fluid dynamics technique is employed to numerically study the three-dimensional model of the internal airflow in the new design. The effects of air velocity variation on turbulence strength, negative pressure, Re, and wall pressure distribution are investigated based on simulation data and previous studies. The results show that the turbulence strength and Re increased with increase in inlet air velocity. Pressure profiles inside the rotor varied significantly with positive pressure observed at the channel exits. Minimal inlet velocity maintains the flow field in the rotor interior below 100 m/s, which gives the ideal turbulence required to minimize yarn quality deterioration. The dual-feed rotor spinning unit showed more orderly streamline patterns with fewer vortices compared to the conventional one. The numerical simulation can provide insights on airflow studies and some guidelines for future prototyping and experiments to further improve the new design.

scholarly journals Numerical Simulation of a Propeller-Type Turbine for In-Pipe Installation

2021 ◽  
Vol 83 (1) ◽  
pp. 1-16
Author(s):  
Oscar Darío Monsalve Cifuentes ◽  
Jonathan Graciano Uribe ◽  
Diego Andrés Hincapié Zuluaga
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Computational Fluid Dynamics ◽  
Pipe Wall ◽  
Three Dimensional ◽  
Hydraulic Efficiency ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Mesh Independence ◽  
Using Data

In this work, a 76 mm diameter propeller-type turbine is numerically investigated using a parametric study and computational fluid dynamics. The three-dimensional model of the turbine is modeled using data available in the bibliography. A mesh independence study is carried out utilizing a tetrahedron-based mesh with inflation layers around the turbine blade and the pipe wall. The best efficiency point is determined by the maximum hydraulic efficiency of 64.46 %, at a flow rate of 9.72x10-3 m3/s , a head drop of 1.76 m, and a mechanical power of 107.83 W. Additionally, the dimensionless distance y+, pressure, and velocity contours are shown.

scholarly journals 3-D simulation using for hydraulic calculation of the heat Accumulator

2018 ◽  
Vol 240 ◽  
pp. 05011
Author(s):  
Olha Kletska ◽  
Anatoliy Falendysh ◽  
Arthur Kagramanjan ◽  
Andrey Onishchenko
Keyword(s):  
3D Modeling ◽  
Pressure Difference ◽  
Static Pressure ◽  
Three Dimensional ◽  
Hydraulic Calculation ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Software Environment ◽  
Heat Accumulator ◽  
The Given

The article is devoted to the peculiarities of hydraulic calculation of the heat accumulator in the software environment for 3D modeling - SolidWorks. Based on the results of the calculation, the values of the distribution of the velocities of the water flow and the distribution of the static pressure in the given plane of the heat accumulator were obtained, which eventually made it possible to identify the problem areas in the three-dimensional model and obtain the values of the pressure difference.

Sign in / Sign up

Export Citation Format

Share Document