Effect of Gap Voltage and Pulse-On Time on Material Removal Rate for Electrical Discharge Machining of Al2O3

2015 ◽  
Vol 1115 ◽  
pp. 3-6 ◽  
Author(s):  
M.A. Moudood ◽  
Abdus Sabur ◽  
Mohammad Yeakub Ali ◽  
I.H. Jaafar
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Pyrolytic Carbon ◽  
Carbon Layer ◽  
Peak Current ◽  
Conductive Ceramics ◽  
Pulse On Time

Electrical discharge machining (EDM) is a non-conventional machining technique which can be used to machine non-conductive ceramics. This technique removes materials from the workpiece by thermal energy exerted from series of electrical sparks. Using copper foil as assisting electrode (AE), machining of Al2O3 is done successfully. In this investigation, experiments were performed to study the effect of gap voltage and pulse-on time on material removal rate (MRR) for EDM of Al2O3. The results showed that the lowest and the highest values of gap voltage were 12 V and 14 V, respectively, with a fixed peak current of 1.1 A and pulse-on time of 8 μs. Beyond these two voltage values, material cannot be removed due to insufficient pyrolytic carbon layer generation. Similarly, pulse-on time is varied from 6 μs to 8 μs when gap voltage is fixed at 14 V and peak current at 1.1 A. MRR, in this case, is increased almost 20 times from a lowest value of 0.006 mm3/min to a highest value of 0.119 mm3/min for the specified gap voltage and pulse-on time.

scholarly journals Effect of Peak Current on Material Removal Rate for Electrical Discharge Machining of Non-Conductive Al2O3 Ceramic

2013 ◽  
Vol 845 ◽  
pp. 730-734 ◽  
Author(s):  
M.A. Moudood ◽  
A. Sabur ◽  
Mohammad Yeakub Ali ◽  
I.H. Jaafar
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Pyrolytic Carbon ◽  
Machining Process ◽  
Tool Electrode ◽  
Peak Current ◽  
Assisting Electrode

Electrical discharge machining (EDM) is a non-conventional machining process where materials are removed by the thermal energy exerted from series of electrical sparks. This process is applied for machining of non-conductive alumina (Al2O3). The workpiece is covered with the adhesive copper foil to initiate the initial spark between the workpiece and the tool electrode. A pyrolytic carbon (PyC) layer is generated on workpiece surface by dissociating kerosene dielectric after the machining of initial copper assisting electrode (AE) layer. In this study, experiments were performed by varying the peak current and keeping other parameters constant in order to investigate the effect of peak current on material removal rate (MRR) in EDM of Al2O3. The results showed that the lowest and the highest values of peak current were 1.1 A and 1.3 A, respectively. Material cannot be removed due to insufficient PyC layer generation for any values of peak current less than 1.1 A or more than 1.3 A. From the results, it is also observed that the MRR is increased when higher peak current values are used. MRR was found to be 0.052 mm3/min at peak current 1.1 A and it was found to be 0.132 mm3/min at peak current 1.3 A.

Fabrication and experimental investigation of magnetic field assisted powder mixed electrical discharge machining on machining of aluminum 6061 alloy

2019 ◽  
Vol 233 (12) ◽  
pp. 2283-2291 ◽  
Author(s):  
Arun Kumar Rouniyar ◽  
Pragya Shandilya
Keyword(s):  
Magnetic Field ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Tool Wear Rate ◽  
Pulse On Time

Magnetic field assisted powder mixed electrical discharge machining is a hybrid machining process with suitable modification in electrical discharge machining combining the use of magnetic field and fine powder in the dielectric fluid. Aluminum 6061 alloy has found highly significance for the advanced industries like automotive, aerospace, electrical, marine, food processing and chemical due to good corrosion resistance, high strength-to-weight ratio, ease of weldability. In this present work, magnetic field assisted powder mixed electrical discharge machining setup was fabricated and experiments were performed using one factor at a time approach for aluminum 6061 alloy. The individual effect of machining parameters namely, peak current, pulse on time, pulse off time, powder concentration and magnetic field on material removal rate and tool wear rate was investigated. The effect of peak current was found to be dominant on material removal rate and tool wear rate followed by pulse on time, powder concentration and magnetic field. Increase in material removal rate and tool wear rate was observed with increase in peak current, pulse on time and a decrease in pulse off time, whereas, for material removal rate increases and tool wear rate decreases up to the certain value and follow the reverse trend with an increase in powder concentration. Material removal rate was increased and tool wear rate was decreased with increase in magnetic field.

Influence of Process Parameters on Characteristics of Electrical Discharge Machining of PH17-4 Stainless Steel

2015 ◽  
Vol 14 (03) ◽  
pp. 189-202 ◽  
Author(s):  
V. Vikram Reddy ◽  
P. Madar Valli ◽  
A. Kumar ◽  
Ch. Sridhar Reddy
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

In the present work, an investigation has been made into the electrical discharge machining process during machining of precipitation hardening stainless steel PH17-4. Taguchi method is used to formulate the experimental layout, to analyze the effect of each process parameter on machining characteristics and to predict the optimal choice for each electrical discharge machining process parameters namely, peak current, pulse on time and pulse off time that give up optimal process performance characteristics such as material removal rate, surface roughness, tool wear rate and surface hardness. To identify the significance of parameters on measured response, the analysis of variance has been done. It is found that parameters peak current and pulse on time have the significant affect on material removal rate, surface roughness, tool wear rate and surface hardness. However, parameter pulse off time has significant affect on material removal rate. Confirmation tests are conducted at their respective optimum parametric settings to verify the predicted optimal values of performance characteristics.

Comparative evaluation of powder-mixed and ultrasonic-assisted rough die-sinking electrical discharge machining based on pulse characteristics

2019 ◽  
Vol 233 (14) ◽  
pp. 2515-2530 ◽  
Author(s):  
R Rajeswari ◽  
MS Shunmugam
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Graphite Powder ◽  
Machining Process ◽  
Machined Surface ◽  
Ultrasonic Assisted ◽  
Pulse On Time

Electrical discharge machining is used in the machining of complicated shapes in hardened molds and dies. In rough die-sinking stage, attempts are made to enhance material removal rate with a consequential reduction in cycle time. Powder mix and ultrasonic assistance are employed in the electrical discharge machining process to create gap conditions favoring material removal. In the present work, experiments are carried out on hardened D3 die steel using full-factorial design based on three levels of voltage, current and pulse on time. The gap phenomena in graphite powder-mixed and ultrasonic-assisted rough electrical discharge machining are studied using a detailed analysis of pulse shapes and their characteristic trains. Two new parameters, namely, energy expended over a second ( E) and performance factor ( PF) denoting the ratio of energy associated with sparks to total discharge energy, bring out gap conditions effectively. In comparison with the conventional electrical discharge machining for the selected condition, it is seen that the graphite powder mixed in the dielectric enhances the material removal rate by 20.8% with E of 215 J and PF of 0.227, while these values are 179.8 J and 0.076 for ultrasonic-assisted electrical discharge machining with marginal reduction of 3.9%. Cross-sectional images of workpieces also reveal the influence of electrical discharge machining conditions on the machined surface. The proposed approach can be extended to different powder mix and ultrasonic conditions to identify condition favoring higher material removal.

Statistical analysis of material removal rate and surface roughness in electrical discharge turning of titanium alloy (Ti-6Al-4V)

2016 ◽  
Vol 232 (9) ◽  
pp. 1603-1614 ◽  
Author(s):  
Vikas Gohil ◽  
Yogesh M Puri
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Machining Parameters ◽  
Peak Current ◽  
Pulse On Time

Electrical discharge turning is a unique form of electrical discharge machining process, which is being especially developed to generate cylindrical forms and helical profiles on the difficult-to-machine materials at both macro and micro levels. A precise submerged rotating spindle as a work holding system was designed and added to a conventional electrical discharge machine to rotate the workpiece. A conductive preshaped strip of copper as a forming tool is fed (reciprocate) continuously against the rotating workpiece; thus, mirror image of the tool is formed on the circumference of the workpiece. The machining performance of electrical discharge turning process is defined and influenced by its machining parameters, which directly affects the quality of the machined component. This study presents an investigation on the effects of the machining parameters, namely, pulse-on time, peak current, gap voltage, spindle speed and flushing pressure, on the material removal rate (MRR) and surface roughness (Ra) in electrical discharge turning of titanium alloy Ti-6Al-4V. This has been done by means of Taguchi’s design of experiment technique. Analysis of variance as well as regression analysis is performed on the experimental data. The signal-to-noise ratio analysis is employed to find the optimal condition. The experimental results indicate that peak current, gap voltage and pulse-on time are the most significant influencing parameters that contribute more than 90% to material removal rate. In the context of Ra, peak current and pulse-on time come up with more than 82% of contribution. Finally, the obtained predicted optimal results were verified experimentally. It was shown that the error values are all less than 6%, confirming the feasibility and effectiveness of the adopted approach.

Modelling of Material Removal Rate in EDM of Nonconductive ZrO2 Ceramic by Taguchi Method

2013 ◽  
Vol 393 ◽  
pp. 246-252 ◽  
Author(s):  
A. Sabur ◽  
Mohammad Yeakub Ali ◽  
M.A. Maleque
Keyword(s):  
Taguchi Method ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Pyrolytic Carbon ◽  
Carbon Layer ◽  
Machining Process ◽  
Machined Surface ◽  
Pulse On Time ◽  
Pulse Off Time

Electro discharge machining (EDM) technique, a noncontact machining process, is applied for structuring nonconductive ZrO2 ceramic. A conductive layer of adhesive copper is applied on the workpiece surface to initiate the sparks. Kerosene is used as dielectric for creation of continuous conductive pyrolytic carbon layer on the machined surface. Experiments are conducted by varying the peak current (Ip), pulse-on time (Ton), pulse-off time (Toff) and gap voltage (Vg). Correlating these variables a mathematical model for material removal rate (MRR) is developed using Taguchi method. The optimized parametric conditions are determined for higher MRR through ANOVA and signal to noise (S/N) ratio analysis. The results showed that the Ip and Ton are the significant parameters of MRR in EDM for nonconductive ZrO2 ceramic. The model also showed that MRR increases with the increase of Ip and Ton, but the process is controlled by Ip as a whole.

scholarly journals Optimization of EDM Process Parameter for MRR and SR of 17- 4 PH Steel Using Response Surface Methodology

2018 ◽  
Vol 1 (2) ◽  
Author(s):  
SHUBHRATA NAGPAL
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Optimization Techniques ◽  
Pulse On Time

In the present work, an attempt has been made for material removal rate and surface roughness by response surface optimization techniques in Electrical discharge machining. Electrical discharge machining, commonly known as EDM, is a process that is used to remove metal through the action of an electrical discharge of short duration and high current density between the work piece and too. This work presents the results of a mathematical investigation carried out to the effects of machining parameters such as current, pulse on time, pulse off time and lift time on material removal rate and surface roughness in electrical discharge machining of 17-4 PH steel by using copper electrode. Response surface methodology and ANOVA techniques are used for data analysis to solve the multi-response optimization. To validate the optimum levels of the parameter, confirmation run was performed by setting the parameters at optimum levels. Material Removal Rate during the process has been taken as productivity estimate with the objective to maximize it. With an intention of minimizing surface roughness is been considered as most important output parameter. It is found that the good agreement of that current is most significant parameter for material removal rate and less for surface roughness followed by pulse on time and lift time.

High Performance in EDM Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 500 ◽  
pp. 259-265 ◽  
Author(s):  
Faizul Ezmat Abdul Hamid ◽  
Mohd Amri Lajis
Keyword(s):  
Pulse Duration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
High Performance ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Hardened Steel ◽  
Peak Current ◽  
Aisi D2

In this paper an attempt has been made to investigate the performance of an electrode made through powder metallurgy (PM) of copper tungsten during electrical discharge machining (EDM). Experimental results are presented on electrical discharge machining of AISI D2 hardened steel in kerosene with a copper tungsten (Cu35% - W65%) tool electrode made through PM method with a constant duty factor of 80%. In term of high performance EDM process, higher peak current (>20A) and pulse duration (>400µs) with a high machining efficiency were used. Experimental results have shown that machining at a peak current of 40A and pulse duration of 400µs yields the highest material removal rate (MRR) whereas machining at a peak current of 20A and pulse duration of 400µs yields the lowest tool wear rate (TWR). The lowest surface roughness appears at the lowest material removal rate which is at a peak current of 20A and pulse duration of 600µs. The optimum machining performance can be performed by the combination of pulse duration and peak current at 600µs and 40A respectively.

scholarly journals Optimization of Process Parameters for Minimum Surface Roughness in Wire Electrical Discharge Machining of AISI 1045 Steel Using Taguchi Method

2021 ◽  
Vol 9 (10) ◽  
pp. 989-997
Author(s):  
Rouhan Rafiq
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Wire Electrical Discharge Machining ◽  
Input Parameters ◽  
Pulse On Time

Abstract: One of the important non-traditional machining processes is Wire Electrical Discharge Machining, used for machining difficult to machine materials like composites and inter-metallic materials. WEDM involves complex physical and chemical process including heating and cooling. Accompanying the development of mechanical industry, the demand for alloy materials having high hardness, toughness and impact resistance are increasing. The WEDM satisfy the present demands of the manufacturing industries such as better finish, low tolerance, higher production rate, miniaturization etc. The consistent quality of parts being machined in WEDM is difficult because the process parameters cannot be controlled effectively. The problem of arriving at the optimum levels of the operating parameters has attracted the attention of the researcher and practicing engineers for a very long time. The objective of the present study was to experimentally investigate the effects of various Wire Electrical Discharge Machining variables on Surface Roughness and Material Removal Rate of AISI 1045 using ANOVA method. Taguchi’s L18 Orthogonal Array was used to conduct experiments, which correspond to randomly chosen different combination of process parameters: wire type, pulse on time, pulse off time, peak current, servo voltage, wire feed rate, flushing pressure each to be varied in three different levels. The surface roughness and material removal rate were selected as output responses for the present investigation. The effect of all the input parameters on the output responses have been analyzed using analysis of variance (ANOVA). The effect of variation in input parameters has been studied on the output responses. Plots of S/N ratio have been used to determine the best relationship between the responses and the input parameters. In other words, the optimum set of input parameters for minimum surface roughness and maximum material removal rate were determined. It has been found that wire type, pulse on time are most significant factors for surface roughness and wire type, pulse on time, pulse off time, wire feed rate are most significant factors for material removal rate. Keywords: Input Parameters, Wire Electric Discharge Machining, ANOVA, Taguchi

scholarly journals Performance Evaluation of SiC Powder Mixed Electrical Discharge Machining: A Case of Wire Cut Mode with Re-Circulating Molybdenum Wire

2021 ◽  
Author(s):  
Muhammad Qaiser Saleem ◽  
Maham Naqvi ◽  
Sarmad Ali Khan ◽  
Nadeem Ahmad Mufti ◽  
Kashif Ishfaq
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Molybdenum Wire ◽  
Powder Concentration ◽  
Pulse On Time ◽  
Wire Wear

Abstract Review of the available literature on powder mixed electrical discharge machining (PMEDM) indicates, that most of the research has been done for “die sinking machining mode” whereas the “wire cut machining mode” has not received due attention despite being an important process variant. This work employs Silicon Carbide (SiC) powder mixed dielectric fluid for machining of AISI D2 in “wire cut” mode with re-circulating molybdenum wire (an economic and chemically stable proposition as tool). The effect of five process parameters (powder concentration, peak current, pulse on time, nozzle flushing pressure and stand-off distance) have been evaluated on surface roughness, kerf width, material removal rate and wire wear ratio using Taguchi’s approach. It is found that for surface roughness, higher current and low to moderate concentration levels (2 to 4g/l) deteriorate surface quality; higher values of pressure and stand-off distance are also seen to adversely affect it. For material removal rate, pulse on time as well as its interactions with powder concentration and current, are statistically significant. A higher pulse on with smaller and moderate powder concentrations (2g/l and 4g/l) reduces MRR. For wire wear ratio, current is the sole significant factor (PCR of ~ 65%). SEM analysis of the machined workpiece for the maximum MRR condition quantifies recast layer as ~ 19microns. An indirect comparison with the reported values for non-powdered EDM process indicates that for the similar wire (molybdenum), the use of SiC powder maintains the surface roughness and kerf values, for a much harder D2 material used in this work.

Sign in / Sign up

Export Citation Format

Share Document