Mechanical Properties of Hybrid Nylon-Steel- and Steel-Fibre-Reinforced High Strength Concrete at Low Fibre Volume Fraction

2010 ◽  
Vol 168-170 ◽  
pp. 1704-1707 ◽  
Author(s):  
Ming Kun Yew ◽  
Othman Ismail
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
High Strength Concrete ◽  
Steel Fiber ◽  
Volume Fraction ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete

The mechanical properties of hybrid nylon-steel-fiber-reinforced concrete were investigated in comparison to that of the steel-fiber-reinforced concrete, at the same volume fraction (0.5%). The combining of fibers, often called hybridization is investigated in this paper for a very high strength concrete of an average compressive strength of 105 MPa. Test results showed that fibers when used in a hybrid nylon-steel fibers reinforced concrete form could result in superior composite performance compared to steel-fiber-reinforced concrete. The basic property of the hybridized material that was evaluated and analyzed extensively was the modulus of rupture (MOR) and splitting tensile while the compressive strength was only slightly decreased compared to single steel fiber reinforced concrete. There is a synergy effect in the hybrid fibers system.

scholarly journals Optimization of the Fine to Coarse Aggregate Ratio for the Workability and Mechanical Properties of High Strength Steel Fiber Reinforced Concretes

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5202
Author(s):  
Mohammad Iqbal Khan ◽  
Wasim Abbass ◽  
Mohammad Alrubaidi ◽  
Fahad K. Alqahtani
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Steel Fiber ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Fresh State

High-strength concrete is used to provide quality control for concrete structures, yet it has the drawback of brittleness. The inclusion of fibers improves the ductility of concrete but negatively affects the fresh properties of fiber-reinforced concrete. The effects of different fine to coarse aggregate ratios on the fresh and hardened properties of steel fiber reinforced concrete were investigated in this study. Mixtures were prepared with various fine to coarse aggregate (FA/CA) ratios incorporating 1% steel fiber content (by volume) at constant water to cement ratio. The workability, unit weight, and temperature of the concrete in the fresh state, and the mechanical properties of steel-fiber-reinforced concrete (SFRC) were investigated. The inclusion of fiber in concrete influenced the mobility of concrete in the fresh state by acting as a barrier to the movement of coarse aggregate. It was observed that the concrete with an FA/CA ratio above 0.8 showed better flowability in the fresh state, whilst an above 0.9 FA/CA ratio requires excessive superplasticizer to maintain the flowability of the mixtures. The compressive and flexural strength of SFRC increased with an increase in the FA/CA ratio by around 10% and 28%, respectively. Experimental values of compressive strength and flexural strength showed good agreement, however, modulus of elasticity demonstrated slightly higher values. The experimentally obtained measurements of the mechanical properties of SFRC conformed reasonably well with the available existing prediction equations, and further enabled establishing predictive isoresponse interactive equations within the scope of the investigation domain.

scholarly journals Effects of Reinforcing Fiber Strength on Mechanical Properties of High-Strength Concrete

Fibers ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 93 ◽  
Author(s):  
Yun ◽  
Lim ◽  
Choi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Strength Concrete ◽  
Steel Fiber ◽  
Fiber Strength ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Strength Concrete

: This paper investigates the effects of the tensile strength of steel fiber on the mechanical properties of steel fiber-reinforced high-strength concrete. Two levels of steel fiber tensile strength (1100 MPa and 1600 MPa) and two steel fiber contents (0.38% and 0.75%) were used to test the compression, flexure, and direct shear performance of steel fiber-reinforced high-strength concrete specimens. The aspect ratio for the steel fiber was fixed at 80 and the design compressive strength of neat concrete was set at 70 MPa to match that of high-strength concrete. The performance of the steel fiber-reinforced concrete that contained high-strength steel fiber was superior to that which contained normal-strength steel fiber. In terms of flexural performance in particular, the tensile strength of steel fiber can better indicate performance than the steel fiber mixing ratio. In addition, a compression prediction model is proposed to evaluate compression toughness, and the model results are compared. The predictive model can anticipate the behavior after the maximum load.

Study on the Dynamic Performance of Steel Fiber Reinforced Concrete in SHPB Experiment

2013 ◽  
Vol 700 ◽  
pp. 140-143 ◽  
Author(s):  
Li Li Huang ◽  
Wei Shi
Keyword(s):  
Reinforced Concrete ◽  
High Strength Concrete ◽  
Steel Fiber ◽  
Dynamic Performance ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Strength Concrete ◽  
Shpb Test

It is important to enhance the ductility of high strength concrete (HSC), and one possible direction is to use steel fibers reinforced, named steel fiber reinforced high strength concrete (SFRHSC).In this paper, The crack characteristics of steel fiber reinforced concrete is investigated in the SHPB test. The incident wave and transmission wave varying with the time have been obtained by SHPB experiment. The relationship curve for stress and strain of material concrete has also been obtained.

Steel Fiber Reinforced Concrete to Improve the Characteristics of Fire-Resistant Concrete

2016 ◽  
Vol 845 ◽  
pp. 220-225 ◽  
Author(s):  
Yenny Nurchasanah ◽  
Mohamed Alfitouri Masoud ◽  
Mochammad Solikin
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Modulus Of Elasticity ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Concrete Specimen ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Carbonation Process

The effect of strength, weight, and fibers on properties of concrete at different temperatures is highlighted at this research to analyze the compressive strength and modulus of elasticity of steel fiber reinforced concrete (SFRC) on 1% and 1.5% of volume fractions at three temperature levels 200°C, 400°C and 600°C. This study compare the compressive strength and modulus elasticity between normal concrete and SFRC in various volume fraction of steel fiber as reinforcement on elevated temperature heating up to 600°C. Materials were tested to find out the quality of the material before making the concrete specimen. The tests were performed compressive test and modulus of elasticity. The addition of 1% and 1.5% steel fiber in concrete mix is advantageous for concrete. Overall the compressive strength of concrete was increased as the percentage of steel fiber in concrete increases. At 1.5%, steel fiber reinforced concrete showed a better overall residual strength and better crack resistance than non-fiber concrete. The carbonation process for concrete with steel fiber is a little influenced by temperature compare to concrete without steel fiber. The concrete with 1.5 % steel fiber demonstrated the highest compressive and modulus of elasticity value, 23.5 and 17172MPa at 600°C respectively. It is expected that in future concrete having steel fiber will act as a fire protective considerably.

Mechanical properties of steel fiber reinforced concrete material in construction of road bridge deck

2021 ◽  
Vol 16 (4) ◽  
pp. 169-176
Author(s):  
Xiaohu Luo
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Steel Fiber ◽  
Fiber Content ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Bridge Construction

In order to improve the application effect of steel fiber reinforced concrete (SFRC) in road bridge construction, the mechanical properties of SFRC with different fiber content were analyzed. The SFRC specimens with 0%, 0.5%, 1%, 1.5% and 2% fiber content were designed, and the mechanical properties were tested. The results showed that the compressive strength first increased and then decreased with the increase of fiber content, and the maximum compressive strength of SFRC1.5 reached 40.86 MPa, increasing by 7.19%; the increase amplitude of tensile strength of SFRC1.5 was 73.04%, which was the most obvious; the flexural strength of SFRC increased with the increase of fiber content, and the flexural strength of SFRC2 was 9.78 MPa, increasing by 94.43%. It is concluded from the experimental results of a case study that SFRC1.5 presents the optimal overall mechanical properties and is more suitable for road bridge construction.

Sign in / Sign up

Export Citation Format

Share Document