The Finite Element Modeling and Analysis of Involute Spur Gear

2012 ◽  
Vol 516-517 ◽  
pp. 673-677 ◽  
Author(s):  
Shun Xu ◽  
Yan Zhang
Keyword(s):  
Finite Element ◽  
Mechanical Design ◽  
Three Dimensional ◽  
Spur Gear ◽  
Analysis Model ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
Modeling And Analysis ◽  
Gear Mesh ◽  
Design Software

Through three-dimensional mechanical design software Pro/E to build a spur gear solid model, using ANSYS software for the gear mesh, as well as the constraints imposed by the most unfavorable load to determine the location of the discussion, in order to get accurate finite element analysis model. By analyzing, this shows that the effectiveness of the application of ANSYS in gear calculation.

scholarly journals Finite element analysis of T-joint of mechanical connecting channels

2020 ◽  
Vol 12 (12) ◽  
pp. 168781402097774
Author(s):  
Jiawei Wang ◽  
Fachao Li ◽  
Zibo Chen ◽  
Baishu Li ◽  
Jue Zhu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Rail Transit ◽  
Force Analysis ◽  
Analysis Model ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
Before And After ◽  
Design Software

This paper studies the force and deformation of the connecting channel in Ningbo rail transit construction, which firstly used the mechanical shield method. Steel-concrete composite structural segments are used in the T-joint of connecting channel. The cutting part of the segments are replaced by the concrete and fiberglass instead of reinforced concrete. Basing on a variety of three-dimensional design software and ABAQUS finite element analysis software, a refined finite element analysis model of the special segments is established. By considering the influence of curved joint bolts, the force analysis of the special segments under the structural state before and after construction is performed. According to the analysis and comparison of the deformation of the segments with and without the bolts, it is concluded that the steel-concrete segments can withstand the pressure of the soil before and after the construction. Suggestions for the safety of the design and construction of the segments are put forward.

Modeling and experimental verification on directivity of an electret cell array loudspeaker

2012 ◽  
Vol 24 (3) ◽  
pp. 326-333 ◽  
Author(s):  
Yu-Chi Chen ◽  
Wen-Ching Ko ◽  
Han-Lung Chen ◽  
Hsu-Ching Liao ◽  
Wen-Jong Wu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Digital Control System ◽  
Analysis Model ◽  
Cell Array ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
The Finite Element Analysis ◽  
Directivity Characteristics

We propose a model to give us a method to investigate the characteristic three-dimensional directivity in an arbitrarily configured flexible electret-based loudspeaker. In recent years, novel electret loudspeakers have attracted much interest due to their being lightweight, paper thin, and possessing excellent mid- to high-frequency responses. Increasing or decreasing the directivity of an electret loudspeaker makes it excellent for adoption to many applications, especially for directing sound to a particular area or specific audio location. Herein, we detail a novel electret loudspeaker that possesses various directivities and is based on various structures of spacers instead of having to use multichannel amplifiers and a complicated digital control system. In order to study the directivity of an electret loudspeaker based on an array structure which can be adopted for various applications, the horizontal and vertical polar directivity characteristics as a function of frequency were simulated by a finite-element analysis model. To validate the finite-element analysis model, the beam pattern of the electret loudspeaker was measured in an anechoic room. Both the simulated and experimental results are detailed in this article to validate the various assertions related to the directivity of electret cell-based smart speakers.

Finite Element Method Analysis for Marine Semi-Built-Up Crankshaft Shrinkage Fitting

2014 ◽  
Vol 472 ◽  
pp. 693-698
Author(s):  
Shou Qi Cao ◽  
Shu Man Fu ◽  
Ya Wen Zhu ◽  
Yan Ling Han
Keyword(s):  
Finite Element ◽  
Induction Heating ◽  
Three Dimensional ◽  
Deformation Condition ◽  
Analysis Model ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element ◽  
Method Analysis

Based on the theories of induction heating and thermal conductivity, and by establishing a three-dimensional finite element analysis model including the induction coil, crank cheek and air, the pattern of temperatures field distribution and thermal deformation condition of the crank cheek during the period of induction heating were numerically simulated with software ANSYS. The simulation result showed that, by setting a circular coil inside the crank cheek, a uniform temperatures field around the hole would be obtained after a certain period of induction heating. As a result, the crankshaft would reach a high quality shrinkage fitting, manifesting the feasibility of the application of induction heating to the crankshaft shrinkage fitting.

scholarly journals Biomechanical assessment of different fixation methods in mandibular high sagittal oblique osteotomy using a three-dimensional finite element analysis model

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Charles Savoldelli ◽  
Elodie Ehrmann ◽  
Yannick Tillier
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Analysis Model ◽  
Element Analysis ◽  
Fixation Methods ◽  
Oblique Osteotomy ◽  
Von Mises

AbstractWith modern-day technical advances, high sagittal oblique osteotomy (HSOO) of the mandible was recently described as an alternative to bilateral sagittal split osteotomy for the correction of mandibular skeletal deformities. However, neither in vitro nor numerical biomechanical assessments have evaluated the performance of fixation methods in HSOO. The aim of this study was to compare the biomechanical characteristics and stress distribution in bone and osteosynthesis fixations when using different designs and placing configurations, in order to determine a favourable plating method. We established two finite element models of HSOO with advancement (T1) and set-back (T2) movements of the mandible. Six different configurations of fixation of the ramus, progressively loaded by a constant force, were assessed for each model. The von Mises stress distribution in fixations and in bone, and bony segment displacement, were analysed. The lowest mechanical stresses and minimal gradient of displacement between the proximal and distal bony segments were detected in the combined one-third anterior- and posterior-positioned double mini-plate T1 and T2 models. This suggests that the appropriate method to correct mandibular deformities in HSOO surgery is with use of double mini-plates positioned in the anterior one-third and posterior one-third between the bony segments of the ramus.

Wear analysis of eco-friendly non-asbestos friction-lining material applied in an automotive drum brake: Experimental and finite-element analysis

2021 ◽  
pp. 135065012110167
Author(s):  
Dinesh Shinde ◽  
Mukesh Bulsara ◽  
Jeet Patil
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Surface Wear ◽  
Analysis Model ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
Drum Brake ◽  
Wear Analysis ◽  
Lining Material ◽  
Friction Lining

Brake friction lining material is the critical element of a braking system, since it provides friction resistance to the rotating drum for controlling automobiles. The present study involves wear analysis of newly developed eco-friendly non-asbestos friction lining material for automotive drum brake applications using experimental study, finite-element analysis, and microstructural investigations. Theoretical interpretation of braking force at different automobile speeds was derived using fundamentals. Specimen drum brake liner with eco-friendly material compositions was produced using an industrial hot compression molding process at one of the manufacturer. The surface wear of the liner was measured using an effective and accurate method. Furthermore, a finite-element analysis model was developed considering actual operating conditions and various components of the drum brake system. The model was elaborated for various result outcomes, including Von-Mises stresses and total deformation of components of the drum brake, and further used to estimate the surface wear of the friction lining material in terms of transverse directional deformation. Finally, microstructural analysis of the friction lining material was carried out using scanning electron microscopy and energy dispersive spectroscopy. From the results, it is seen that the developed friction lining material is wear resistant. The finite-element analysis model can be effectively utilized to study the tribological characteristics of friction lining materials.

Sign in / Sign up

Export Citation Format

Share Document