Vertical Loading Test on the Bearing Capacity of Large-Diameter Filling-Piles in the Mudstone and Sandstone Foundation

2013 ◽  
Vol 639-640 ◽  
pp. 587-592 ◽  
Author(s):  
Hui Yang ◽  
Xue Liang Jiang ◽  
Jun Fu
Keyword(s):  
Bearing Capacity ◽  
Load Transfer ◽  
Large Diameter ◽  
Load Test ◽  
Sediment Thickness ◽  
Loading Test ◽  
Friction Resistance ◽  
Vertical Loading ◽  
Pile Diameter ◽  
Side Friction

Based on the vertical loading test results of large-diameter filling pile near an electric factory in the sandstone and mudstone foundation, the load transfer mechanism and vertical loading bearing behavior of the pile were discussed. The analysis shows that the pile mainly behaves as friction piles and the vertical bearing capacity is mainly supplied by side friction resistance. The pile side friction is related to the section displacement of pile, the pile load and the soil characteristic. The pile end resistence is related to pile end settlement, pile diameter, rock-socketed length,rock elasticity modulus of pile end, sediment thickness and pile construction technical. The pile end resistence linearly increases with the settlement of pile end. In tis paper, the dead-load test is recommended in determination the pile bearing capacity and the sediment thickness should be strictly controlled in order to meet the standard. In the intermediary weathered sand-mudstone, the pile end should inset two times of pile diameter for pile whose diameter is 800mm. The pile end should inset 2 meters for pile whose diameter is 1500mm.

Experiment Research on Bored Pile with Post-Grouting Technology

2013 ◽  
Vol 838-841 ◽  
pp. 854-857
Author(s):  
Rui Chao Cheng ◽  
Xin Yu
Keyword(s):  
Bearing Capacity ◽  
Static Load ◽  
Load Test ◽  
Static Load Test ◽  
Pile Head ◽  
Experiment Research ◽  
Friction Resistance ◽  
Bored Pile ◽  
Post Grouting ◽  
Side Friction

The bearing capacity characteristics and side friction characters of post-grouting pile were studied in the static load test which included two piles with post-grouting or not. When the pile head settlements were same, the loads applied on the pile top were used to analyze the bearing properties of post-grouting pile. We got the ultimate side friction of post-grouting pile after fitting test curves of relations between friction resistance and displacement. The tests indicate that both the bearing capacity characteristics and side friction of post-grouting pile are increased in various degrees.

Back-Analysis for Design Parameters of Large Diameter Bored Piles

2013 ◽  
Vol 671-674 ◽  
pp. 186-189
Author(s):  
Werasak Raongjant ◽  
Meng Jing
Keyword(s):  
Test Data ◽  
Load Transfer ◽  
Static Load ◽  
Large Diameter ◽  
Back Analysis ◽  
Load Test ◽  
Design Parameters ◽  
Static Load Test ◽  
Friction Resistance ◽  
Bored Piles

Field test data from three instrumented large diameter bored piles in Pattaya city of Thailand were analyzed to study the behavior of load transfer mechanism from the pile to soil. The pile load test data were obtained from conventional static load test. These bored piles used for conventional static load test have the same diameter of 0.80 m and different length in the range of 25 m to 32 m. Results from back-analysis found that the skin friction resistance, β, has the value between 0.20 and 0.64 and the bearing capacity at end of piles, Nq, which is in the range of 10 to150, is much lower than the theoretical values proposed by other researchers before.

scholarly journals Field Tests of Super-Long and Large-Diameter Drilled Shaft Pile Foundations

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Peisen Wang ◽  
Hongyan Ding ◽  
Jialin Zhou ◽  
Wenjun Hu ◽  
Xuechen Gu ◽  
...  
Keyword(s):  
Load Transfer ◽  
Large Diameter ◽  
Soil Layer ◽  
Field Tests ◽  
Load Test ◽  
Pile Foundations ◽  
Static Load Test ◽  
Mutual Compensation ◽  
Shaft Resistance ◽  
Pile Diameter

This study investigated the compressive behaviour of super-long pile foundations with large diameters. Three 52 m, 73 m, and 83 m long piles with a diameter of 1500 mm, 1500 mm, and 1800 mm were cast and tested, respectively. Given that large loading was required, an improved compressive static load test was introduced, and the load transfer mechanism, shaft resistance development, and distribution were analysed. This study found that the transferred load decreased along the pile during each applied load, but the gradients were different. For most layers, when increasing the load, the shaft resistance developed in the upper layers first, while the shaft resistance from the lower part did not always fully develop. Moreover, the “mutual compensation” phenomenon was discovered, which was when the shaft softening occurred from one soil layer, the shaft hardening of the other soil would occur simultaneously. Under consideration of the soil layer differences around these piles, it was recommended that shaft and base grouting should be applied on 52 m and 73 m piles, while only shaft grouting should be applied on the 83 m pile. For this longest pile design, whose toe resistance was discovered to be very small, increasing the pile length was not appropriate; thus, it was preferable to increase the pile diameter to increase the ultimate bearing capacity.

Bearing Capacity and Mechanical Behavior Experiment on Large Diameter-Expanding Pile

2011 ◽  
Vol 243-249 ◽  
pp. 457-460
Author(s):  
Jian Qing Jiang
Keyword(s):  
Bearing Capacity ◽  
Ultimate Load ◽  
Load Transfer ◽  
Large Diameter ◽  
Foundation Engineering ◽  
Loading Test ◽  
Axial Forces ◽  
Static Loading Test ◽  
Friction Pile ◽  
Bearing Behavior

Combined with the pile foundation engineering of a super-large highway bridge, vertical static loading test of pile with expanded diameter was carried out. The pile’s load-settlement curves, axial forces of the different pile’s section and the pile-soil interaction friction were obtained from the test. The load transfer mechanism and bearing behavior of the pile with expanded diameter under vertical load were studied. The results show that the ultimate load of the testing pile is more than 6000kN. The pile-soil interaction of the pile with expanded diameter behaviors as friction pile, and the bearing capacity of the segment with expanded diameter accounts for 40% of the ultimate load. These studies provide important references for similar projects.

Research on Load Transfer Behavior of Cement-Soil Mixing Piles by Load Test

2012 ◽  
Vol 174-177 ◽  
pp. 228-231
Author(s):  
Dong Xiao Zhang ◽  
Peng Li He
Keyword(s):  
Axial Force ◽  
Load Transfer ◽  
Load Test ◽  
Loading Test ◽  
Soil Mixing ◽  
Before And After ◽  
Static Loading Test ◽  
Transfer Behavior ◽  
Cement Soil ◽  
Side Friction

The pile axial strains were measured according to the results of static loading test. The axial force and side friction of pile were calculated, and load transfer behaviors were researched. Analysis of the data shows that cement-soil mixing pile has the characteristics of friction piles. The rapid reducing of the upper pile axial force and friction show that load passed within a certain range. Horizontal crack occurred at the upper of the pile. Before and after the destructing of the pile load transfer mechanism is different.

Numerical investigation of the monotonic drained lateral behaviour of large diameter rigid piles in medium dense uniform sand

Géotechnique ◽  
2021 ◽  
pp. 1-39
Author(s):  
Huan Wang ◽  
M. Fraser Bransby ◽  
Barry M. Lehane ◽  
Lizhong Wang ◽  
Yi Hong
Keyword(s):  
Numerical Investigation ◽  
Load Transfer ◽  
Large Diameter ◽  
Offshore Wind ◽  
Soil Pressure ◽  
Lateral Capacity ◽  
Pile Diameter ◽  
Centrifuge Tests ◽  
Lateral Response ◽  
Loading Eccentricity

This paper presents a numerical investigation of the monotonic lateral response of large diameter monopiles in drained sand with configurations typical of those employed to support offshore wind turbines. Results from new centrifuge tests using instrumented monopiles in uniform dry sand deposits are first presented and used to illustrate the suitability of an advanced hypoplastic constitutive model to represent the sand in finite element analyses of the experiments. These analyses are then extended to examine the influence of pile diameter and loading eccentricity on the lateral response of rigid monopiles. The results show no dependency of suitably normalized lateral load transfer curves on the pile diameter and loading eccentricity. It is also shown that, in a given uniform sand, the profile with depth of net soil pressure at ultimate lateral capacity is independent of the pile diameter because of the insensitivity of the depth to the rotation centre for a rigid pile. A normalization method is subsequently proposed which unifies the load-deflection responses of different diameter rigid piles at a given load eccentricity.

FULL SCALE STATIC LOAD TEST ON THE SPIDER NET SYSTEM

2015 ◽  
Vol 77 (11) ◽  
Author(s):  
Helmy Darjanto ◽  
Masyhur Irsyam ◽  
Sri Prabandiyani Retno
Keyword(s):  
Bearing Capacity ◽  
Load Transfer ◽  
Static Load ◽  
Full Scale ◽  
Load Test ◽  
Static Load Test ◽  
Specific Element ◽  
Soil Stratum ◽  
Applied Loading ◽  
Shallow Footing

The Spider Net System Footing (SNSF) is a raft foundation system that commonly used in Indonesia. It contains a plate, downward ribs system for reinforcement, and the compacted filled soil. The ribs are in longitudinal and transversal, called as settlement rib and in diagonal direction, named as construction rib. This paper explores the load transfer mechanism along the plate, the ribs, filled soil and the base soil under the footing system. The mechanism is investigated by conducting full scale static load test on SNSF. Strain gauges were installed to monitor the strain increment of each footing elements during loading. 3D numerical analysis was also conducted to verify the experimental results. To analyze the results, Load-Ultimate Ratio Factor (L-URF) was proposed. L-URF was a ratio between ultimate soil bearing capacity of the SNSF and the applied loading at specific element. Higher the L-URF value means higher loading applied at its associate element. Both experimental and numerical results show that at the first stage the loading was fully carried out by the tip of the ribs and transferred to the soil stratum under the footing system. Increasing the loading, the ribs, plate, and filled soil altogether sustain the loading and then transferred to the soil stratum below the footing system. The results also affirm that SNSF generate higher bearing capacity compare with simple shallow footing.  

Instrumented load tests in mudstone: pile capacity and settlement prediction

2002 ◽  
Vol 39 (6) ◽  
pp. 1254-1272 ◽  
Author(s):  
J R Omer ◽  
R Delpak ◽  
R B Robinson
Keyword(s):  
Load Transfer ◽  
Load Capacity ◽  
Large Diameter ◽  
Soft Rock ◽  
Site Investigation ◽  
Alternative Methods ◽  
Vertical Loading ◽  
South Wales ◽  
Pile Design ◽  
Load Tests

The present work stems from the design of a viaduct in South Wales, U.K., where full-scale pile testing was carried out to assess whether the proposed design methods would meet the required load capacity and settlement criteria for the working piles. Five fully instrumented large diameter bored cast in situ piles, up to 30 m deep, were installed in weathered mudstone and tested under vertical loading. A sixth pile, which had no shaft instrumentation, was formed with a voided toe. In conjunction with vast soil data from 218 site investigation boreholes, the extensive data produced from the load tests were analyzed to quantify the key parameters considered to influence load transfer and settlement behaviour. Each pile was first calibrated using four methods to establish the as-built stiffness, taking into account the nonlinearity of concrete and the effect of partial steel encasement. It is demonstrated that the current national norms for bored pile design in cohesive soil – soft rock are overconservative for South Wales ground conditions. To ameliorate this, alternative methods are proposed, which lead to improved reliability and accuracy in shaft and base capacity assessment. In addition, a numerical model is developed that can be used to predict the complete load-settlement variation up to the ultimate state. The model is sufficiently expounded to allow its immediate application in pile design by geotechnical engineers.Key words: piled foundations, load tests, bearing capacity and settlement, Mercia mudstone.

Construction Method and Numerical Analysis on the Bearing Capacity of the Large Diameter and Abyssal Pile Located in Complex Karst Area

2013 ◽  
Vol 639-640 ◽  
pp. 688-693
Author(s):  
Jin Yi ◽  
Guo Jing He ◽  
Si Si Liu ◽  
Zhi Yong Li ◽  
Zu En Zheng
Keyword(s):  
Bearing Capacity ◽  
Load Transfer ◽  
Large Diameter ◽  
Construction Method ◽  
Karst Area ◽  
Karst Region ◽  
Pile Capacity ◽  
Construction Methods ◽  
Geological Conditions ◽  
Transfer Method

This paper introduced construction method for deep pile of Zishui bridge through karst region and the checking results of the pile bearing capacity. Firstly, main structure of Zishui bridge was simply introduced. Secondly, according to the special geological conditions, construction methods for bored piles in water and drilling platform were described. The discussion focused on the problem of boring and grouting in karst foundation and their solutions. Finally, to ensure that the pile capacity can meet the design requirements, load transfer method was used on the part of pile foundation to calculate the bearing capacity. Results showed that pile bearing capacity meet the requirements, and the feasibility and correctness of construction method of Zishui bridge was also verified,which provides references for the design and construction of the same civil engineering.

Testing Study on Bearing Behavior of Belled Large-Diameter PHC Pipe Pile by NAKS (Nakabori Kakutei System) Construction Method

2013 ◽  
Vol 353-356 ◽  
pp. 533-539 ◽  
Author(s):  
Wen Xu ◽  
Yu Bin Hou
Keyword(s):  
Bearing Capacity ◽  
Large Diameter ◽  
Field Testing ◽  
Construction Method ◽  
Load Test ◽  
Test Field ◽  
Static Load Test ◽  
Pipe Pile ◽  
Bored Pile ◽  
Bearing Behavior

Through field static load test and pile shaft axial force test, field testing study is conducted on bearing behavior of NAKS-construction-method belled large-diameter PHC pipe pile; besides, the test result is compared with that of hammering-method PHC pipe pile and bored pile with same pile length and diameter under the same site condition. The result shows that the ultimate bearing capacity of NAKS-construction-method belled large-diameter PHC pipe pile is slightly inferior to hammering-method PHC pipe pile but obviously superior to that of bored pile. Compared with traditional hammering-method pipe pile, the pile side resistance of NAKS-construction-method belled pipe pile is smaller; however, the higher toe resistance will give better play to bearing capacity of bearing stratum of pile toe; moreover, it is found that under the action of ultimate load and failure load, the maximum settlement and final settlement of NAKS-construction-method belled pipe pile tip are obviously lower than that of other test piles, which is conductive to lessening foundation settlement of upper structure.

Sign in / Sign up

Export Citation Format

Share Document