Evaluation of Operational Properties of Composite Reinforcement Used in Concrete Structures

2014 ◽  
Vol 880 ◽  
pp. 57-61
Author(s):  
Viktor V. Rodevich ◽  
Artem A. Ovchinnikov ◽  
Elena V. Shilnikova
Keyword(s):  
Experimental Studies ◽  
Basalt Fiber ◽  
Lightweight Aggregate ◽  
Alkali Resistance ◽  
Lightweight Aggregate Concrete ◽  
Performance Study ◽  
Building Envelopes ◽  
Satisfactory Performance ◽  
High Alkali ◽  
Composite Reinforcement

The paper is devoted to the study of composite reinforcement made of glass fiber and basalt fiber, in particular their operational properties under the aggressive alkaline lightweight aggregate concrete environment. Their thermal resistance being sufficiently less than that of the regular steel composites they may be used in three-layered building envelopes to provide enhanced thermal properties. However there is lack of data and experimental results on the topic. Previous research indicated high alkali resistance of basalt fiber reinforcement, but there is a need in further studies. For the objective of the composite reinforcement that is used as flexible connectors for layer wall panels, a series of experimental studies. Research data have shown satisfactory performance study of flexible links.

scholarly journals Ductility and flexure of lightweight expanded clay basalt fiber reinforced concrete slab

2021 ◽  
Vol 17 (1) ◽  
pp. 74-81
Author(s):  
Vera V. Galishnikova ◽  
Alireza Heidari ◽  
Paschal C. Chiadighikaobi ◽  
Adegoke Adedapo Muritala ◽  
Dafe Aniekan Emiri
Keyword(s):  
Reinforced Concrete ◽  
Concrete Slab ◽  
Basalt Fiber ◽  
Lightweight Aggregate ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Lightweight Aggregate Concrete ◽  
Concrete Slabs ◽  
Reinforced Concrete Slab ◽  
Chopped Basalt Fiber

Relevance. The load on a reinforced concrete slab with high strength lightweight aggregate concrete leads to increased brittleness and contributes to large deflection or flexure of slabs. The addition of fibers to the concrete mix can improve its mechanical properties including flexure, deformation, toughness, ductility, and cracks. The aims of this work are to investigate the flexure and ductility of lightweight expanded clay concrete slabs reinforced with basalt fiber polymers, and to check the effects of basalt fiber mesh on the ductility and flexure. Methods. The ductility and flexural/deflection tests were done on nine engineered cementitious composite (expanded clay concrete) slabs with dimensions length 1500 mm, width 500 mm, thickness 65 mm. These nine slabs are divided in three reinforcement methods types: three lightweight expanded clay concrete slab reinforced with basalt rebars 10 mm (first slab type); three lightweight expanded clay concrete slab reinforced with basalt rebars 10 mm plus dispersed chopped basalt fiber plus basalt fiber polymer (mesh) of cells 2525 mm (second slab type); three lightweight expanded clay concrete slab reinforced with basalt rebars 10 mm plus dispersed basalt fiber of length 20 mm, diameter 15 m (third slab type). The results obtained showed physical deflection of the three types of slab with cracks. The maximum flexural load for first slab type is 16.2 KN with 8,075 mm deflection, second slab type is 24.7 KN with 17,26 mm deflection and third slab type 3 is 32 KN with 15,29 mm deflection. The ductility of the concrete slab improved with the addition of dispersed chopped basalt fiber and basalt mesh.

scholarly journals Numerical and experimental studies of bent elements of basalt fiber reinforced concrete with prestressed glass composite reinforcement under static and short-term dynamic loads

2019 ◽  
Vol 221 ◽  
pp. 01026
Author(s):  
Vasilii Plevkov ◽  
Konstantin Kudyakov
Keyword(s):  
Reinforced Concrete ◽  
Experimental Studies ◽  
Basalt Fiber ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Dynamic Effects ◽  
Glass Composite ◽  
Short Term ◽  
Concrete Elements ◽  
Composite Reinforcement

The article shows studies of bending basalt fiber reinforced concrete elements with pre-stressed glass composite reinforcement under static and short-term dynamic effects. Main results of numerical and experimental studies are presented. It is experimentally established and theoretically confirmed that a significant increase in the strength and crack resistance of the normal sections of concrete bent elements is observed when using basalt fiber reinforcement and pre-stressed glass composite reinforcement.

scholarly journals Evaluation of Stress–Strain Behavior of Self-Compacting Rubber Lightweight Aggregate Concrete under Uniaxial Compression Loading

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4064 ◽  
Author(s):  
Jing Lv ◽  
Tianhua Zhou ◽  
Qiang Du ◽  
Kunlun Li ◽  
Kai Sun
Keyword(s):  
Compressive Strength ◽  
Failure Modes ◽  
Experimental Studies ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Peak Strain ◽  
Stress Strain ◽  
Aggregate Concrete ◽  
Rubber Particles ◽  
Strain Relationship

The recycling of waste tires in lightweight aggregate concrete (LC) would achieve huge environmental and societal benefits, but the effects of rubber particles on the partial properties of LC are not clear (e.g., the stress–strain relationship). In this paper, uniaxial compressive experiments were conducted to evaluate the stress–strain relationship of self-compacting rubber lightweight aggregate concrete (SCRLC). Rubber particles were used to replace sand by volume, and substitution percentages of 0%, 10%, 20%, 30%, 40%, and 50% were set as influence factors. Experimental results indicate that with increased rubber particles substitution percentage, the cubic compressive strength and axial compressive strength of SCRLC decreased, while the failure modes of SCRLC prism specimens gradually changed from brittle to ductile failure. As the rubber particles substitution percentage increased from 0% to 50%, the peak strain of SCRLC increased whereas peak stress, elastic modulus, and peak secant modulus of SCRLC deceased, the descending stage of stress–strain curves became softer. The rubber particles substitution percentage of 30% was the critical point at which an obvious change in the properties of SCRLC occurred. Based on the data collected from experimental studies, a predictive model for SCRLC was established and a further prediction of the SCRLC stress–strain relationship was given.

Experimental Studies on Blast-Resistance of HFR-LWC Beams Enhanced with Membrane Action

2020 ◽  
Vol 20 (12) ◽  
pp. 2050142
Author(s):  
Wanxiang Chen ◽  
Lisheng Luo ◽  
Fanjun Meng ◽  
Hang Sun
Keyword(s):  
Failure Modes ◽  
Blast Resistance ◽  
Experimental Studies ◽  
Field Tests ◽  
Lightweight Aggregate ◽  
Failure Pattern ◽  
Lightweight Aggregate Concrete ◽  
Hybrid Fibers ◽  
Membrane Action ◽  
Close Range

Support-induced membrane action can enhance the resistance, while altering the failure pattern, of reinforced concrete (RC) members under static/dynamic loadings. Nevertheless, the membrane effect on the load-response is regarded as a safety factor in current design guides, hence, a thorough understanding of the resistance capability of RC members in the presence of membrane actions is considered essential. To quantitatively depict the membrane behavior and its influence on the blast-resistance and failure pattern of Hybrid Fiber Reinforced-Lightweight Aggregate Concrete (HFR-LWC) beams, a specially built end-constraint clamp is developed to provide membrane actions on the structural component subjected to the blast load simultaneously. A series of field tests are conducted to investigate the dynamic behaviors of the HFR-LWC beams under close-range detonations. Overpressure-time histories of shock waves induced by the close-range explosive charge are captured. Then the deflection-responses and failure modes of the HFR-LWC beams are further investigated. The responses of the clamped HFR-LWC beam under blast loadings can be well simulated, and the blast-resistances of the beam-type members with membrane action are evaluated reasonably. The results show that membrane action is beneficial for the bridging effects of hybrid fibers and the interlocking effects of coarse aggregate, thereby giving rise to the ductile failures of HFR-LWC beam. The maximum deflections of the clamped HFR-LWC beam decrease by about 60% compared with simply-supported HFR-LWC beam in this paper, illustrating that the blast-resistance may be seriously underestimated if the membrane effects are ignored in structural design.

Study on Hybrid Fiber Reinforced Lightweight Aggregate Concrete

2013 ◽  
Vol 477-478 ◽  
pp. 949-952
Author(s):  
Yan Chen
Keyword(s):  
Tensile Strength ◽  
Basalt Fiber ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Hybrid Fiber ◽  
Aggregate Concrete ◽  
Concrete Mix ◽  
Fiber Materials ◽  
Pva Fiber ◽  
Better Than

For lightweight aggregate concrete, fiber materials can reinforce its toughness and strength better and improve its segregation degree greatly. Specifically, as the experiment indicates, the fluidity of concrete mix decreases slightly after 0.5% basalt fiber and 0.5% PVA fiber are incorporated into the concrete with FA ceramsite as lightweight aggregate. However, its segregation degree reduces about 50%. And its 28d cubic compressive strength increases 0.7% and 28d splitting tensile strength increases 12.7%. Therefore, this effect is better than that of adding only one kind of fiber.

scholarly journals Mechanical Properties of Chopped Basalt Fiber-Reinforced Lightweight Aggregate Concrete and Chopped Polyacrylonitrile Fiber Reinforced Lightweight Aggregate Concrete

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1715 ◽  
Author(s):  
Yusheng Zeng ◽  
Xianyu Zhou ◽  
Aiping Tang ◽  
Peng Sun
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Shear Strength ◽  
Water Absorption ◽  
Basalt Fiber ◽  
Lightweight Aggregate ◽  
Splitting Tensile Strength ◽  
Lightweight Aggregate Concrete ◽  
Polyacrylonitrile Fiber ◽  
Aggregate Concrete

In this study, an experimental investigation was conducted on the mechanical properties of lightweight aggregate concrete (LWAC) with different chopped fibers, including basalt fiber (BF) and polyacrylonitrile fiber (PANF). The LWAC performance was studied in regard to compressive strength, splitting tensile strength and shear strength at age of 28 days. In addition, the oven-dried density and water absorption were measured as well to confirm whether the specimens match the requirement of standard. In total, seven different mixture groups were designed and approximately 104 LWAC samples were tested. The test results showed that the oven-dried densities of the LWAC mixtures were in range of 1.819–1.844 t/m3 which satisfied the definition of LWAC by Chinese Standard. Additionally, water absorption decreased with the increasing of fiber content. The development tendency of the specific strength of LWAC was the same as that of the cube compressive strength. The addition of fibers had a significant effect on reducing water absorption. Adding BF and PANF into concrete had a relatively slight impact on the compressive strength but had an obvious effect on splitting tensile strength, flexural strength and shear strength enhancement, respectively. In that regard, a 1.5% fiber volume fraction of BF and PANF showed the maximum increase in strength. The use of BF and PANF could change the failure morphologies of splitting tensile and flexural destruction but almost had slight impact on the shear failure morphology. The strength enhancement parameter β was proposed to quantify the improvement effect of fibers on cube compressive strength, splitting tensile strength, flexural strength and shear strength, respectively. And the calculation results showed good agreement with test value.

Sign in / Sign up

Export Citation Format

Share Document