Strip Shape Analysis of Asymmetrical Cold Rolling of Thin Strip

2010 ◽  
Vol 97-101 ◽  
pp. 81-84 ◽  
Author(s):  
Zheng Yi Jiang ◽  
Xiao Zhong Du ◽  
Yan Bing Du ◽  
Dong Bin Wei ◽  
Matthew Hay
Keyword(s):  
Finite Element ◽  
Cold Rolling ◽  
Finite Element Model ◽  
Shape Control ◽  
Thickness Distribution ◽  
Element Model ◽  
Thin Strip ◽  
Strip Shape ◽  
Rolling Practice ◽  
Good Agreement

Strip shape control during cold rolling of thin strip is a challenge in rolling practice. In the paper, finite element model of strip shape during cold rolling of thin strip in asymmetrical rolling case was successfully developed, and the strip shape such as the thickness distribution along the strip width have been obtained. The developed finite element model has been verified with the experimental value, which shows they are in good agreement. The obtained results are applicable to control the rolled thin strip shape in practice.

Analysis of Advanced Strip Shape during Cold Rolling of Thin Strip

2010 ◽  
Vol 654-656 ◽  
pp. 206-209
Author(s):  
Zheng Yi Jiang ◽  
Xiao Zhong Du ◽  
Yan Bing Du ◽  
Dong Bin Wei ◽  
Xiao Feng He
Keyword(s):  
Finite Element ◽  
Cold Rolling ◽  
Finite Element Model ◽  
Element Model ◽  
Thin Strip ◽  
Speed Ratio ◽  
Strip Shape ◽  
Element Simulation ◽  
Edge Drop ◽  
Rolling Practice

The demand of thin gauge strip with good quality such as the strip shape and surface finish is significantly increasing. In this study, finite element model of the strip shape during cold rolling of thin strip in asymmetrical rolling was developed, and the finite element simulation of the thin strip shape has been carried out in LS-DYNA. The effects of reduction and speed ratio on the strip shape and profile and the strip edge drop have been obtained. The developed finite element model has been verified with the experimental data. The obtained results are applicable to the control of the rolled thin strip shape in rolling practice.

Modelling of Strip Shape and Profile during Cold Rolling of Ultra Thin Strip

2012 ◽  
Vol 706-709 ◽  
pp. 1421-1426
Author(s):  
Zheng Yi Jiang ◽  
Xiao Wei Cheng ◽  
Xiao Zhong Du ◽  
Dong Bin Wei ◽  
Xiao Feng He
Keyword(s):  
Finite Element ◽  
Cold Rolling ◽  
Thickness Distribution ◽  
Element Model ◽  
Work Roll ◽  
Thin Strip ◽  
Asymmetrical Rolling ◽  
Strip Shape ◽  
Experimental Values ◽  
Edge Drop

In this paper, finite element models of the strip shape during cold rolling of ultra thin strip in both symmetrical and asymmetrical rolling cases have been successfully developed, and the strip shape such as the thickness distribution along the strip width has been obtained. The strip shape and edge drop are discussed under both symmetrical and asymmetrical rolling conditions. Simulation results show that the asymmetrical rolling can reduce strip edge drop dramatically. The work roll edge curve also affects strip shape significantly. The developed finite element model has been verified with the experimental values.

scholarly journals Modeling of Strip Shape during Cold Rolling of Thin Strip

2010 ◽  
Vol 443 ◽  
pp. 9-14 ◽  
Author(s):  
Zheng Yi Jiang ◽  
X.Z. Du ◽  
Yan Bing Du ◽  
Dong Bin Wei ◽  
Matthew Hay
Keyword(s):  
Finite Element ◽  
Cold Rolling ◽  
Rolling Force ◽  
Thickness Distribution ◽  
Simulation Models ◽  
Element Model ◽  
Thin Strip ◽  
Strip Shape ◽  
Element Simulation ◽  
Strip Quality

Strip shape is an important factor affecting the strip quality significantly during cold rolling of thin strip. In the paper, finite element simulation models of the strip shape in cold rolling for both symmetrical and asymmetrical rolling cases were successfully developed. The strip edge drop and the effect of the rolling force on the strip shape (the thickness distribution along the strip width) have been obtained. The developed finite element model has been verified with the experimental value, which shows they are in good agreement. The obtained results are applicable to control the rolled thin strip shape during cold rolling practice.

Analysis of Strip Shape in Cold Rolling of Thin Strip

2011 ◽  
Vol 189-193 ◽  
pp. 2980-2985
Author(s):  
Zheng Yi Jiang
Keyword(s):  
Finite Element ◽  
Cold Rolling ◽  
Thickness Distribution ◽  
Element Model ◽  
Thin Strip ◽  
Finite Element Models ◽  
Asymmetrical Rolling ◽  
Strip Shape ◽  
Strip Edge ◽  
Edge Drop

In this paper, finite element models of the strip shape during cold rolling of thin strip in both symmetrical and asymmetrical rolling cases have been successfully developed, and the effects of rolling parameters on strip shape such as the thickness distribution along the strip width have been obtained. The strip edge drop and shape are discussed under both symmetrical and asymmetrical rolling conditions. Simulation results show that the asymmetrical rolling can reduce the strip edge drop dramatically, which is useful in improving the strip shape and reducing the energy cost during cold rolling of thin strip. The developed finite element model has been verified with the experimental value. The obtained results are applicable to control the rolled thin strip shape in practice.

Finite Element Analysis of Thin Strip Profile in Asymmetric Cold Rolling Considering Work Roll Crossing and Shifting

2014 ◽  
Vol 1061-1062 ◽  
pp. 515-521 ◽  
Author(s):  
Abdulrahman Aljabri ◽  
Zheng Yi Jiang ◽  
Dong Bin Wei
Keyword(s):  
Finite Element ◽  
Cold Rolling ◽  
Finite Element Model ◽  
Rolling Force ◽  
Element Model ◽  
Work Roll ◽  
Rolling Process ◽  
Thin Strip ◽  
Asymmetric Rolling ◽  
Element Analysis

Cold rolled thin strip has received a great deal of attention through technological and theoretical progress in the rolling process, as well as from researchers who have focused on some essential parameters of strip such as its shape and profile. This paper describes the development of a 3-D finite element model of the shape of thin strip during cold rolling to simulate the cold rolling of WCS (work roll crossing and shifting) in asymmetric rolling. This finite element model considers the asymmetrical rolling parameters such as variations in the diameters of the rolls and the crossing angle as the work roll shifts on the strip during cold rolling. The shape and profile of the strip are discussed in the asymmetrical and symmetrical rolling conditions, while the total rolling force and distribution of stress are discussed in the case where the roll cross angle and axial shifting roll changes. The results can then be used to control the shape and profile of thin strip during rolling.

A plane-strain elastoplastic finite-element model for cold rolling of thin strip

1992 ◽  
Vol 34 (3) ◽  
pp. 195-210 ◽  
Author(s):  
P. Gratacos ◽  
P. Montmitonnet ◽  
C. Fromholz ◽  
J.L. Chenot
Keyword(s):  
Finite Element ◽  
Cold Rolling ◽  
Finite Element Model ◽  
Plane Strain ◽  
Element Model ◽  
Thin Strip

Rigid-Plastic Impact of Single Angular Particles

2021 ◽  
Author(s):  
Sandeep Dhar
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Orientation Dependence ◽  
Particle Orientation ◽  
Rigid Plastic ◽  
Plastic Model ◽  
Model Predictions ◽  
Good Agreement ◽  
Angular Particles

The trajectory of an angular particle as it cuts a ductile target is, in general, complicated because of its dependence not only on particle shape, but also on particle orientation at the initial instant of impact. This orientation dependence has also made experimental measurement of impact parameters of single angular particles very difficult, resulting in a relatively small amount of available experimental data in the literature. The current work is focused on obtaining measurements of particle kinematics for comparison to rigid plastic model developed by Papini and Spelt. Fundamental mechanisms of material removal are identified, and measurements of rebound parameters and corresponding crater dimensions of single hardened steel particles launched against flat aluminium alloy targets are presented. Also a 2-D finite element model is developed and a dynamic analysis is performed to predict the erosion mechanism. Overall, a good agreement was found among the experimental results, rigid-plastic model predictions and finite element model predictions.

Modeling and Control of a 2-D Membrane Mirror With a PZT Bimorph

Aerospace ◽  
2006 ◽  
Author(s):  
Eric J. Ruggiero ◽  
Daniel J. Inman
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Structural Control ◽  
Shape Control ◽  
Actuation Voltage ◽  
Linear Quadratic Regulator ◽  
Element Model ◽  
Optical Quality ◽  
Active System ◽  
Linear Quadratic

The future of space satellite technology lies in ultra-large mirrors and radar apertures for significant improvements in imaging and communication bandwidths. The availability of optical-quality membranes drives a parallel effort for structural models that can capture the dominant dynamics of large, ultra-flexible satellite payloads. Unfortunately, the inherent flexibility of membrane mirrors wrecks havoc with the payload's on-orbit stability and maneuverability. One possible means of controlling these undesirable dynamics is by embedding active piezoelectric ceramics near the boundary of the membrane mirror. In doing so, active feedback control can be used to eliminate detrimental vibration, perform static shape control, and evaluate the health of the structure. In the present work, a piezoceramic wafer was attached in a bimorph configuration near the boundary of a tensioned rectangular membrane sample. A finite element model of the system was developed to capture the relevant system dynamics from 0 – 500 Hz. The finite element model was compared to experimental results with fair agreement. Using the validated finite element models, structural control using Linear Quadratic Regulator (LQR) control techniques were then used to demonstrate effective vibration control. Typical results show that less than 12 V of actuation voltage is required to eliminate detrimental vibration of the membrane samples in less than 15 ms. The functional gains of the active system are also derived and presented. These spatially descriptive control terms dictate favorable regions within the membrane domain to place sensors.

Displacement Properties of Newly Developed 3-Dimensional Piezoelectric Actuator at Various AC Frequencies

2007 ◽  
Vol 534-536 ◽  
pp. 1441-1444 ◽  
Author(s):  
Man Soon Yoon ◽  
Y.G. Choi ◽  
Soon Chul Ur
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Piezoelectric Actuator ◽  
Element Model ◽  
Vibration Modes ◽  
Maximum Strain ◽  
Electromechanical Properties ◽  
3 Dimensional ◽  
The Finite Element Model ◽  
Good Agreement

The electromechanical properties of a newly proposed 3-dimensional piezoelectric actuator have been investigated. Especially, the effects of 3-dimensional geometry on the maximum tip displacement were carefully investigated. As a result, it was found that the maximum strain of the 3-dimensional piezoelectric device was significantly enhanced up to 4.5 times higher than that of a disk shape device. This data was in good agreement with the finite element model analysis of strains and vibration modes. Moreover, the field -induced displacement stability of dome-shaped 3- dimensional piezoelectric actuator at various ac freguencies was superior to Rainbow actuator.

Sign in / Sign up

Export Citation Format

Share Document