scholarly journals Microstructural Characterization of Thermal Barrier Coatings Glazed by a High Power Laser

2016 ◽  
Vol 723 ◽  
pp. 247-251 ◽  
Author(s):  
Hong Zhou ◽  
Fei Li ◽  
Jun Wang ◽  
Bao De Sun
Keyword(s):  
Surface Roughness ◽  
Thermal Barrier Coatings ◽  
High Power ◽  
Microstructural Characterization ◽  
Ceramic Coatings ◽  
Thermal Barrier ◽  
High Power Laser ◽  
Power Laser ◽  
Barrier Coatings ◽  
Plasma Sprayed

Thermal barrier coatings have been widely used in in both energy and propulsion systems. Plasma-sprayed thermal barrier coatings have relatively high interconnected porosity and lamina structure, which bring out a low bond strength, and lead to a short thermal cycling life. Lasers can be used for modification of materials surface. In this paper, plasma-sprayed thermal barrier coatings were laser-glazed by a high power laser in order to modify the structures. The microstructure of laser-glazed TBCs is investigated. The change on surface roughness has been examined. The result indicates that a smooth and dense glazed surface with craters and a network of microcracks is obtained after laser-glazing. The laser-glazed region consists of a columnar microstructure. There are segmentation microcracks in the laser-glazed coatings, which don’t run through the coatings along thickness. Surface roughness has been reduced significantly for the laser treated ceramic coatings.

scholarly journals Ceramic Thermal Barrier Coatings for Turbine Engine Components

1982 ◽  
Author(s):  
D. S. Duvall ◽  
D. L. Ruckle
Keyword(s):  
Thermal Barrier Coatings ◽  
Ceramic Coatings ◽  
Thermal Barrier ◽  
Barrier Coatings ◽  
Turbine Engine ◽  
Thermal Environments ◽  
Strain Tolerance ◽  
Endurance Testing ◽  
Plasma Sprayed ◽  
Cooling Air

The durability of plasma sprayed ceramic thermal barrier coatings subjected to cyclic thermal environments has been improved substantially by improving the strain tolerance of the ceramic structure and also by controlling the substrate temperature during the application of the coating. Improved strain tolerance was achieved by using ceramic structures with increased porosity, microcracking or segmentation. Plasma spraying on a controlled-temperature substrate also has been shown to improve durability by reducing harmful residual stresses. The most promising of the strain tolerant ceramic coatings have survived up to 6000 cycles of engine endurance testing with no coating or vane platform damage. In side-by-side engine tests, thermal barrier coatings have shown that they greatly reduce platform distress compared to conventionally coated vanes in addition to permitting reductions in cooling air and attendant increases in engine efficiency.

scholarly journals Thermal Shock and Oxidation Stability Tests to Grade Plasma Sprayed Functionally Gradient Thermal Barrier Coatings

2019 ◽  
Vol 1 (1) ◽  
pp. 1-11
Author(s):  
Pasupuleti Kirti Teja ◽  
Parvati Ramaswamy ◽  
Narayana Murthy S.V.S.
Keyword(s):  
Thermal Barrier Coatings ◽  
Inconel 718 ◽  
Oxidation Stability ◽  
Ceramic Coatings ◽  
Functionally Graded ◽  
Yttria Stabilized Zirconia ◽  
Thermal Barrier ◽  
Stabilized Zirconia ◽  
Barrier Coatings ◽  
Plasma Sprayed

Functionally graded layers in thermal barrier coatings reduce the stress gradient between the overlaid ceramic coatings and the underlying metallic component. Introduced to alleviate early onset of spallation of the coating due to thermal expansion mismatch, this facilitates improvement in the life of the component. Conventional thermal barrier coatings typically comprise of duplex layers of plasma sprayed 8% yttria stabilized zirconia (ceramic) coatings on bond coated (NiCrAlY) components/substrates (Inconel 718 for example). This work highlights the superiority of plasma sprayed coatings synthesized from blends of the intermetallic bond coat and ceramic plasma spray powders on Inconel 718 substrates in three-layer configuration over the duplex layered configuration. Assessed through (a) thermal shock cyclic tests (at 1200oC and 1400oC) in laboratory scale basic burner rig test facility and (b) oxidation stability test in high temperature furnace (at 800oC and 1000oC) the functionally graded coatings of certain configurations exhibited more than double the life of the conventional 8% yttria stabilized zirconia duplex (double layer) coatings. Micro- and crystal structure analysis support the findings and results are detailed and discussed.

scholarly journals Morphological and microstructural characterization of laser-glazed plasma-sprayed thermal barrier coatings

2006 ◽  
Vol 200 (9) ◽  
pp. 2929-2937 ◽  
Author(s):  
C. Batista ◽  
A. Portinha ◽  
R.M. Ribeiro ◽  
V. Teixeira ◽  
M.F. Costa ◽  
...  
Keyword(s):  
Thermal Barrier Coatings ◽  
Microstructural Characterization ◽  
Thermal Barrier ◽  
Barrier Coatings ◽  
Plasma Sprayed

Properties of ZrO2-7wt%Y2O3 Thermal Barrier Coatings in Relation to Plasma Spraying Conditions

1997 ◽  
Author(s):  
C. Funke ◽  
B. Siebert ◽  
D. Stöver ◽  
R. Vaßen
Keyword(s):  
Elastic Modulus ◽  
Plasma Spraying ◽  
Thermal Barrier Coatings ◽  
Bond Coat ◽  
Free Edge ◽  
Ceramic Coatings ◽  
Thermal Barrier ◽  
Normal Stresses ◽  
Barrier Coatings ◽  
Plasma Sprayed

Abstract Superalloy samples were coated with thermal barrier coatings (TBC). This TBC-system consisted of two layers. The first layer was a vacuum-plasma sprayed, corrosion resistant layer (MCrAlY) which also acted as a bond coat. The ceramic top layer was atmospheric-plasma sprayed Y2O3-stabilized ZrO2. In order to produce different microstructures, the plasma-spraying parameters for the production of the ceramic coatings were varied. The different ceramic coatings were characterized in terms of porosity and mean elastic modulus. The porosity distribution was also investigated due to its influence on the measured elastic modulus. To record the changes of the plasma sprayed Zirconia due to sintering, the mean elastic modulus of selected coatings was measured as a function of annealing time. One series of TBC-coated specimens was cyclically oxidized at a maximum temperature of 1100°C. After 500 h of thermal cycling, creep within the MCrAlY-bond coat led to a coating failure at both the internal beveled edge and free edge around the specimen. A finite element analysis study of the cyclic oxidation experiment was performed to gain insight into the stress redistributions within the bond coat as a function of time. During the initial temperature increase, critical tensile normal stresses developed above the MCrAlY-Zirconia interface at the free edge. However, these normal stresses became compressive for all following cooling cycles. On the other hand, large tensile normal stresses developed above the MCrAlY-Zirconia interface at the beveled edge during all the cooling cycles. Therefore, high normal stresses responsible for debonding were present within the ceramic coating during all cooling cycles with the most critical stresses occurring at the free edge during the first cooling cycle and near the beveled edge for all the following cooling cycles.

Development and Performance Evaluation of Thick Air Plasma Sprayed Thermal Barrier Coatings

2000 ◽  
Author(s):  
Z.Z. Mutasim ◽  
Y.L. Nava
Keyword(s):  
Thermal Barrier Coating ◽  
Thermal Barrier Coatings ◽  
Ceramic Coatings ◽  
Thermal Barrier ◽  
Air Plasma ◽  
Barrier Coatings ◽  
Barrier Coating ◽  
And Performance ◽  
Plasma Sprayed ◽  
Industrial Gas Turbine

Abstract Air plasma sprayed thermal barrier coatings have been widely used to reduce metal wall temperatures of industrial gas turbine combustor liners. Thermal barrier coatings provide thermal gradients, with the goal of reducing the liner wall temperature to acceptable levels as a result of their low thermal conductivity. A typical thermal barrier coating consists of a 0.1-0.2 mm MCrAlY bond coating and a 0.25-0.35 mm thick 8 wt.% yttria stabilized zirconia ceramic top coating. A method to increase thermal barrier coating effectiveness is the application of thicker ceramic coatings. Development and performance testing of 0.5-0.8 mm thick ceramic coatings are discussed in this paper. Cyclic oxidation tests that simulate industrial gas turbine environments were conducted. Thermal barrier coating degradation-mechanisms were determined from microstructural evaluation of thermally exposed samples.

Sign in / Sign up

Export Citation Format

Share Document