Measurement of Piezoelectric Properties of Pulsed Laser Deposited Hydroxyapatite Thin Films on Platinum or Titanium Substrate

It has been well known that bone has piezoelectric properties and these properties have been considered to be caused by the shift of the center of symmetry of the positive and negative electrical charge due to the strain of the collagen fibers included in the bone. Thus, it has long been considered that there were no piezoelectric effects in the hexagonal hydroxyapatite (HAp) which has center of symmetry of crystal. However, in recent years, the piezoelectric property of artificially synthesized HAp was reported. In the authors’ previous report, a new result which showed the piezoelectricity of the hydroxyapatite (HAp) films fabricated by the pulsed laser deposition (PLD) method was reported. In this study, the effect of poling treatment on piezoelectric constant of pulsed laser deposited HAp films was investigated.

Download Full-text

Observations on the growth of YBa2Cu3O7-δ thin films on MgO by pulsed-laser ablation

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100089652 ◽

1991 ◽

Vol 49 ◽

pp. 1068-1069

Author(s):

M. Grant Norton ◽

C. Barry Carter

Keyword(s):

Thin Film ◽

Thin Films ◽

Laser Ablation ◽

Substrate Surface ◽

Pulsed Laser ◽

Pulsed Laser Ablation ◽

Thin Film Deposition ◽

Film Deposition ◽

Laser Ablation Process ◽

Deposition Parameters

Pulsed-laser ablation has been widely used to produce high-quality thin films of YBa2Cu3O7-δ on a range of substrate materials. The nonequilibrium nature of the process allows congruent deposition of oxides with complex stoichiometrics. In the high power density regime produced by the UV excimer lasers the ablated species includes a mixture of neutral atoms, molecules and ions. All these species play an important role in thin-film deposition. However, changes in the deposition parameters have been shown to affect the microstructure of thin YBa2Cu3O7-δ films. The formation of metastable configurations is possible because at the low substrate temperatures used, only shortrange rearrangement on the substrate surface can occur. The parameters associated directly with the laser ablation process, those determining the nature of the process, e g. thermal or nonthermal volatilization, have been classified as ‘primary parameters'. Other parameters may also affect the microstructure of the thin film. In this paper, the effects of these ‘secondary parameters' on the microstructure of YBa2Cu3O7-δ films will be discussed. Examples of 'secondary parameters' include the substrate temperature and the oxygen partial pressure during deposition.

Download Full-text

TEM sample preparation of wear-tested room-temperature pulsed-laser-deposited thin films of MoS2 by ultramicrotomy

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100151428 ◽

1993 ◽

Vol 51 ◽

pp. 1118-1119

Author(s):

Pamela F. Lloyd ◽

Scott D. Walck

Keyword(s):

Thin Films ◽

Sample Preparation ◽

Room Temperature ◽

High Vacuum ◽

Pulsed Laser ◽

Ultra High Vacuum ◽

Wear Testing ◽

Preparation Technique ◽

Cross Sectional ◽

Aerospace Applications

Pulsed laser deposition (PLD) is a novel technique for the deposition of tribological thin films. MoS2 is the archetypical solid lubricant material for aerospace applications. It provides a low coefficient of friction from cryogenic temperatures to about 350°C and can be used in ultra high vacuum environments. The TEM is ideally suited for studying the microstructural and tribo-chemical changes that occur during wear. The normal cross sectional TEM sample preparation method does not work well because the material’s lubricity causes the sandwich to separate. Walck et al. deposited MoS2 through a mesh mask which gave suitable results for as-deposited films, but the discontinuous nature of the film is unsuitable for wear-testing. To investigate wear-tested, room temperature (RT) PLD MoS2 films, the sample preparation technique of Heuer and Howitt was adapted.Two 300 run thick films were deposited on single crystal NaCl substrates. One was wear-tested on a ball-on-disk tribometer using a 30 gm load at 150 rpm for one minute, and subsequently coated with a heavy layer of evaporated gold.

Download Full-text