A Bilevel Approach to treat the Decomposed Topology Optimization Problem

2010 ◽  
Author(s):  
A. Makrizi ◽  
B. Radi ◽  
A. El Hami
Keyword(s):  
Topology Optimization ◽  
Optimization Problem ◽  
Topology Optimization Problem

Efficient Sensitivity Analysis for Multibody Dynamics Systems Using an Iterative Steps Method With Application in Topology Optimization

2011 ◽  
Author(s):  
Guang Dong ◽  
Zheng-Dong Ma ◽  
Gregory Hulbert ◽  
Noboru Kikuchi ◽  
Sudhakar Arepally ◽  
...  
Keyword(s):  
Sensitivity Analysis ◽  
Topology Optimization ◽  
Multibody Dynamics ◽  
Optimization Problem ◽  
Finite Difference Methods ◽  
Analysis Method ◽  
Topology Optimization Problem ◽  
Design Variables ◽  
Sensitivity Analysis Method ◽  
Rotational Motions

Efficient and reliable sensitivity analyses are critical for topology optimization, especially for multibody dynamics systems, because of the large number of design variables and the complexities and expense in solving the state equations. This research addresses a general and efficient sensitivity analysis method for topology optimization with design objectives associated with time dependent dynamics responses of multibody dynamics systems that include nonlinear geometric effects associated with large translational and rotational motions. An iterative sensitivity analysis relation is proposed, based on typical finite difference methods for the differential algebraic equations (DAEs). These iterative equations can be simplified for specific cases to obtain more efficient sensitivity analysis methods. Since finite difference methods are general and widely used, the iterative sensitivity analysis is also applicable to various numerical solution approaches. The proposed sensitivity analysis method is demonstrated using a truss structure topology optimization problem with consideration of the dynamic response including large translational and rotational motions. The topology optimization problem of the general truss structure is formulated using the SIMP (Simply Isotropic Material with Penalization) assumption for the design variables associated with each truss member. It is shown that the proposed iterative steps sensitivity analysis method is both reliable and efficient.

Topology Optimization for the Single Phase Flow Using Two Point Flux Approximation Model

2013 ◽  
Author(s):  
Guang Dong ◽  
Yulan Song
Keyword(s):  
Porous Media ◽  
Topology Optimization ◽  
Optimization Problem ◽  
Single Phase ◽  
Flow In Porous Media ◽  
Phase Flow ◽  
Approximation Model ◽  
Single Phase Flow ◽  
Topology Optimization Problem ◽  
Flux Approximation

The topology optimization method is extended to solve a single phase flow in porous media optimization problem based on the Two Point Flux Approximation model. In particular, this paper discusses both strong form and matrix form equations for the flow in porous media. The design variables and design objective are well defined for this topology optimization problem, which is based on the Solid Isotropic Material with Penalization approach. The optimization problem is solved by the Generalized Sequential Approximate Optimization algorithm iteratively. To show the effectiveness of the topology optimization in solving the single phase flow in porous media, the examples of two-dimensional grid cell TPFA model with impermeable regions as constrains are presented in the numerical example section.

Topology Optimization Under Independent Multi-Load With Uncertainty

2016 ◽  
Author(s):  
Hae Chang Gea ◽  
Xing Liu ◽  
Euihark Lee ◽  
Limei Xu
Keyword(s):  
Topology Optimization ◽  
Optimization Problem ◽  
Optimization Method ◽  
Engineering Practice ◽  
Worst Case ◽  
Load Uncertainty ◽  
Topology Optimization Problem ◽  
Level Problem ◽  
Upper Level ◽  
Mean Compliance

In this paper, topology optimization under multiple independent loadings with uncertainty is presented. In engineering practice, load uncertainty can be found in many applications. From the literature, researchers have focused mainly on problems containing only a single uncertain external load. However, such idealistic problems may not be very useful in engineering practice. Problems involving multi-loadings with uncertainty are more commonly found in engineering applications. This paper presents a method to solve a system which contains multiple independent loadings with load uncertainty. First, a two-level optimization problem is formulated. The upper level problem is a typical topology optimization problem to minimize the mean compliance in the design using the worst case conditions. The lower level optimization problem is to solve for the worst loadings corresponding to the critical structure response. At the lower level formulation, an unknown-but-bounded model is used to define uncertain loadings. There are two challenges in finding the worst loading case: non-convexity and multi-loadings. The non-convexity problem is addressed by reformulating the problem as an inhomogeneous eigenvalue problem by applying the KKT optimality conditions and the multi-uncertain loadings problem is solved by an iterative method. After the worst loadings are generated, the upper level problem can be solved by a general topology optimization method. The effectiveness of the proposed method is demonstrated by numerical examples.

Multi-material topology optimization of compliant mechanisms via solid isotropic material with penalization approach and alternating active phase algorithm

2020 ◽  
Vol 234 (13) ◽  
pp. 2631-2642
Author(s):  
Behzad Majdi ◽  
Arash Reza
Keyword(s):  
Topology Optimization ◽  
Isotropic Material ◽  
Close Agreement ◽  
Optimization Problem ◽  
Compliant Mechanisms ◽  
Active Phase ◽  
Maximum Displacement ◽  
Topology Optimization Problem ◽  
Solid Phases ◽  
Ansys Workbench

The present study aims at providing a topology optimization of multi-material compliant mechanisms using solid isotropic material with penalization (SIMP) approach. In this respect, three multi-material gripper, invertor, and cruncher compliant mechanisms are considered that consist of three solid phases, including polyamide, polyethylene terephthalate, and polypropylene. The alternating active-phase algorithm is employed to find the distribution of the materials in the mechanism. In this case, the multiphase topology optimization problem is divided into a series of binary phase topology optimization sub-problems to be solved partially in a sequential manner. Finally, the maximum displacement of the multi-material compliant mechanisms was validated against the results obtained from the finite element simulations by the ANSYS Workbench software, and a close agreement between the results was observed. The results reveal the capability of the SIMP method to accurately conduct the topology optimization of multi-material compliant mechanisms.

scholarly journals Stiffness optimization of geometrically nonlinear structures and the level set based solution

2016 ◽  
Vol 7 ◽  
pp. A3 ◽  
Author(s):  
Qi Xia ◽  
Tielin Shi
Keyword(s):  
Topology Optimization ◽  
Level Set ◽  
Optimization Problem ◽  
Two Dimensions ◽  
Geometrically Nonlinear ◽  
Nonlinear Structures ◽  
Element Analysis ◽  
Topology Optimization Problem ◽  
Stiffness Optimization ◽  
Ks Function

Load-normalized strain energy increments between consecutive load steps are aggregated through the Kreisselmeier-Steinhauser (KS) function, and the KS function is proposed as a stiffness criterion of geometrically nonlinear structures. A topology optimization problem is defined to minimize the KS function together with the perimeter of structure and a volume constraint. The finite element analysis is done by remeshing, and artificial weak material is not used. The topology optimization problem is solved by using the level set method. Several numerical examples in two dimensions are provided. Other criteria of stiffness, i.e., the end compliance and the complementary work, are compared.

A Systems Approach to Structural Topology Optimization: Designing Optimal Connections

1996 ◽  
Author(s):  
Tao Jiang ◽  
Mehran Chirehdast
Keyword(s):  
Topology Optimization ◽  
Design Problem ◽  
Large Scale ◽  
Optimization Problem ◽  
Systems Design ◽  
Mathematical Programming Problem ◽  
Structural Topology Optimization ◽  
Structural Topology ◽  
Topology Optimization Problem ◽  
Wide Range

Abstract In this paper, structural topology optimization is extended to systems design. Locations and patterns of connections in a structural system that consists of multiple components strongly affect its performance. Topology of connections is defined, and a new classification for structural optimization is introduced that includes the topology optimization problem for connections. A mathematical programming problem is formulated that addresses this design problem. A convex approximation method using analytical gradients is used to solve the optimization problem. This solution method is readily applicable to large-scale problems. The design problem presented and solved here has a wide range of applications in all areas of structural design. The examples provided here are for spot-weld and adhesive bond joints. Numerous other potential applications are suggested.

Sign in / Sign up

Export Citation Format

Share Document