scholarly journals On the Finite Element Analysis of Shells and their Full Interaction with Navier-Stokes Fluid Flows

2009 ◽  
pp. 1-31 ◽  
Author(s):  
K.J. Bathe ◽  
J.F. Hiller ◽  
H. Zhang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Fluid Flows ◽  
Navier Stokes ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Stokes Fluid ◽  
Full Interaction

Ratcheting due to Thermal Stratification

2019 ◽  
Author(s):  
R. Adibi-Asl ◽  
D. O’Kane ◽  
E. Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Temperature Distribution ◽  
Thermal Stratification ◽  
Fluid Flows ◽  
Uniform Temperature ◽  
Element Analysis ◽  
Steady State Condition ◽  
Thermal Ratcheting ◽  
The Finite Element Analysis

Abstract Thermal ratcheting is required to be checked by most of the piping design codes, specifically the ASME B&PV Code. For cases where the variation of temperature distribution is not uniform, the existing ratchet check methodology for piping is inadequate and therefore the finite element analysis (FEA) is often used to perform ratchet checks. Thermal stratification, in which cold and hot fluid flows are layered in a relatively steady state condition, is a good example of non-linear/non-uniform temperature distribution across the pipe. This paper develops straightforward equations to address thermal stratification in piping. Finite element analysis is used to benchmark the results.

Interactive Graphics for the Analysis of Tires

1985 ◽  
Vol 13 (3) ◽  
pp. 127-146 ◽  
Author(s):  
R. Prabhakaran
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Approximate Solutions ◽  
Interactive Graphics ◽  
Element Analysis ◽  
Analysis Process ◽  
Physical Problems ◽  
The Finite Element Analysis ◽  
Analysis Computer ◽  
Discretization Technique

Abstract The finite element method, which is a numerical discretization technique for obtaining approximate solutions to complex physical problems, is accepted in many industries as the primary tool for structural analysis. Computer graphics is an essential ingredient of the finite element analysis process. The use of interactive graphics techniques for analysis of tires is discussed in this presentation. The features and capabilities of the program used for pre- and post-processing for finite element analysis at GenCorp are included.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Use of the Finite Element Analysis Method in Pedodontics

2018 ◽  
Vol 55 (4) ◽  
pp. 666-675
Author(s):  
Mihaela Tanase ◽  
Dan Florin Nitoi ◽  
Marina Melescanu Imre ◽  
Dorin Ionescu ◽  
Laura Raducu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Model ◽  
Analysis Method ◽  
Ansys Software ◽  
Concentrated Force ◽  
Element Analysis ◽  
Finite Element Analysis Method ◽  
The Finite Element Analysis ◽  
Solid Type

The purpose of this study was to determinate , using the Finite Element Analysis Method, the mechanical stress in a solid body , temporary molar restored with the self-curing GC material. The originality of our study consisted in using an accurate structural model and applying a concentrated force and a uniformly distributed pressure. Molar structure was meshed in a Solid Type 45 and the output data were obtained using the ANSYS software. The practical predictions can be made about the behavior of different restorations materials.

A necessary modification for the finite element analysis of cracked members detection, construction, and justification

2013 ◽  
Vol 83 (7) ◽  
pp. 1087-1096 ◽  
Author(s):  
A. Ranjbaran ◽  
H. Rousta ◽  
M. O. Ranjbaran ◽  
M. A. Ranjbaran ◽  
M. Hashemi ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Cracked Members

Modeling and experimental verification on directivity of an electret cell array loudspeaker

2012 ◽  
Vol 24 (3) ◽  
pp. 326-333 ◽  
Author(s):  
Yu-Chi Chen ◽  
Wen-Ching Ko ◽  
Han-Lung Chen ◽  
Hsu-Ching Liao ◽  
Wen-Jong Wu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Digital Control System ◽  
Analysis Model ◽  
Cell Array ◽  
Element Analysis ◽  
Finite Element Analysis Model ◽  
The Finite Element Analysis ◽  
Directivity Characteristics

We propose a model to give us a method to investigate the characteristic three-dimensional directivity in an arbitrarily configured flexible electret-based loudspeaker. In recent years, novel electret loudspeakers have attracted much interest due to their being lightweight, paper thin, and possessing excellent mid- to high-frequency responses. Increasing or decreasing the directivity of an electret loudspeaker makes it excellent for adoption to many applications, especially for directing sound to a particular area or specific audio location. Herein, we detail a novel electret loudspeaker that possesses various directivities and is based on various structures of spacers instead of having to use multichannel amplifiers and a complicated digital control system. In order to study the directivity of an electret loudspeaker based on an array structure which can be adopted for various applications, the horizontal and vertical polar directivity characteristics as a function of frequency were simulated by a finite-element analysis model. To validate the finite-element analysis model, the beam pattern of the electret loudspeaker was measured in an anechoic room. Both the simulated and experimental results are detailed in this article to validate the various assertions related to the directivity of electret cell-based smart speakers.

Sign in / Sign up

Export Citation Format

Share Document