On the Generation of Instability Tollmien-Schlichting Waves by Free-Stream Turbulence

2017 ◽  
Vol 9 (2) ◽  
pp. 429-438
Author(s):  
Luyu Shen ◽  
Changgen Lu
Keyword(s):  
Boundary Layer ◽  
Acoustic Waves ◽  
Free Stream ◽  
Leading Edge ◽  
S Wave ◽  
S Waves ◽  
Free Stream Turbulence ◽  
Temporal Mode ◽  
Tollmien Schlichting ◽  
Experimental Researches

AbstractThe beginning of the transition from the laminar to a turbulent flow is usually the generation of instability Tollmien-Schlichting (T-S) waves in the boundary layer. Previously, most numerical and experimental researches focused on generating instability T-S waves through the external disturbances such as acoustic waves and vortical disturbances interacting with wall roughness or at the leading-edge of flatplate, whereas only a few paid attention to the excitation of the T-S waves directly by free-stream turbulence (FST). In this study, the generating mechanism of the temporal mode T-S waves under free-stream turbulence is investigated by using direct numerical simulation (DNS) and fast Fourier transform. Wave packets superposed by a group of stability, neutral and instability T-S waves are discovered in the boundary layer. In addition, the relation between the amplitude of the imposed free-stream turbulence and the amplitude of the excited T-S wave is also obtained.

Effects of Weak Free Stream Nonuniformity on Boundary Layer Transition (Keynote Paper)

2003 ◽  
Author(s):  
Jonathan H. Watmuff
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Mean Flow ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
Tollmien Schlichting ◽  
Distorted Waves ◽  
Thickness Variations

Experiments are described in which well-defined FSN (Free Stream Nonuniformity) distributions are introduced by placing fine wires upstream of the leading edge of a flat plate. Large amplitude spanwise thickness variations are present in the downstream boundary layer resulting from the interaction of the laminar wakes with the leading edge. Regions of elevated background unsteadiness appear on either side of the peak layer thickness, which share many of the characteristics of Klebanoff modes, observed at elevated Free Stream Turbulence (FST) levels. However, for the low background disturbance level of the free stream, the layer remains laminar to the end of the test section (Rx ≈ l.4×106) and there is no evidence of bursting or other phenomena associated with breakdown to turbulence. A vibrating ribbon apparatus is used to demonstrate that the deformation of the mean flow is responsible for substantial phase and amplitude distortion of Tollmien-Schlichting (TS) waves. Pseudo-flow visualization of hot-wire data shows that the breakdown of the distorted waves is more complex and occurs at a lower Reynolds number than the breakdown of the K-type secondary instability observed when the FSN is not present.

Leading-edge receptivity of a hypersonic boundary layer on a flat plate

2001 ◽  
Vol 426 ◽  
pp. 73-94 ◽  
Author(s):  
A. A. MASLOV ◽  
A. N. SHIPLYUK ◽  
A. A. SIDORENKO ◽  
D. ARNAL
Keyword(s):  
Boundary Layer ◽  
Acoustic Waves ◽  
Free Stream ◽  
Three Dimensional ◽  
Leading Edge ◽  
Experimental Investigations ◽  
Two Dimensional ◽  
Inclination Angles ◽  
Tollmien Schlichting ◽  
Radiation Conditions

Experimental investigations of the boundary layer receptivity, on the sharp leading edge of a at plate, to acoustic waves induced by two-dimensional and three- dimensional perturbers, have been performed for a free-stream Mach number M∞ = 5.92. The fields of controlled free-stream disturbances were studied. It was shown that two-dimensional and three-dimensional perturbers radiate acoustic waves and that these perturbers present a set of harmonic motionless sources and moving sources with constant amplitude. The disturbances excited in the boundary layer were measured. It was found that acoustic waves impinging on the leading edge generate Tollmien–Schlichting waves in the boundary layer. The receptivity coefficients were obtained for several radiation conditions and intensities. It was shown that there is a dependence of receptivity coefficients on the wave inclination angles.

The generation of Tollmien-Schlichting waves by free-stream turbulence

1996 ◽  
Vol 312 ◽  
pp. 341-371 ◽  
Author(s):  
P. W. Duck ◽  
A. I. Ruban ◽  
C. N. Zhikharev
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Free Stream ◽  
Stokes Equations ◽  
Leading Edge ◽  
Wave Generation ◽  
Generation Process ◽  
Viscous Boundary Layer ◽  
Free Stream Turbulence ◽  
Tollmien Schlichting

The phenomenon of Tollmien-Schlichting wave generation in a boundary layer by free-stream turbulence is analysed theoretically by means of asymptotic solution of the Navier-Stokes equations at large Reynolds numbers (Re → ∞). For simplicity the basic flow is taken to be the Blasius boundary layer over a flat plate. Free-stream turbulence is taken to be uniform and thus may be represented by a superposition of vorticity waves. Interaction of these waves with the flat plate is investigated first. It is shown that apart from the conventional viscous boundary layer of thickness O(Re−1/2), a ‘vorticity deformation layer’ of thickness O(Re−1/4) forms along the flat-plate surface. Equations to describe the vorticity deformation process are derived, based on multiscale asymptotic techniques, and solved numerically. As a result it is shown that a strong singularity (in the form of a shock-like distribution in the wall vorticity) forms in the flow at some distance downstream of the leading edge, on the surface of the flat plate. This is likely to provoke abrupt transition in the boundary layer. With decreasing amplitude of free-stream turbulence perturbations, the singular point moves far away from the leading edge of the flat plate, and any roughness on the surface may cause Tollmien-Schlichting wave generation in the boundary layer. The theory describing the generation process is constructed on the basis of the ‘triple-deck’ concept of the boundary-layer interaction with the external inviscid flow. As a result, an explicit formula for the amplitude of Tollmien-Schlichting waves is obtained.

scholarly journals Analysis of the unstable Tollmien–Schlichting mode on bodies with a rounded leading edge using the parabolized stability equation

2009 ◽  
Vol 623 ◽  
pp. 167-185
Author(s):  
M. R. TURNER ◽  
P. W. HAMMERTON
Keyword(s):  
Asymptotic Theory ◽  
Free Stream ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Reynolds Numbers ◽  
Neutral Stability ◽  
S Wave ◽  
Stability Equation ◽  
Stability Point ◽  
Tollmien Schlichting

The interaction between free-stream disturbances and the boundary layer on a body with a rounded leading edge is considered in this paper. A method which incorporates calculations using the parabolized stability equation in the Orr–Sommerfeld region, along with an upstream boundary condition derived from asymptotic theory in the vicinity of the leading edge, is generalized to bodies with an inviscid slip velocity which tends to a constant far downstream. We present results for the position of the lower branch neutral stability point and the magnitude of the unstable Tollmien–Schlichting (T-S) mode at this point for both a parabolic body and the Rankine body. For the Rankine body, which has an adverse pressure gradient along its surface far from the nose, we find a double maximum in the T-S wave amplitude for sufficiently large Reynolds numbers.

Effect of Elevated Free-Stream Turbulence on Transitional Heat Transfer Over Dual-Scaled Rough Surfaces

2003 ◽  
Author(s):  
Ting Wang ◽  
Matthew C. Rice
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Surface Roughness ◽  
Vortex Shedding ◽  
Free Stream ◽  
Leading Edge ◽  
Test Surface ◽  
Dominant Effect ◽  
Free Stream Turbulence ◽  
Heat Transfer Phenomenon

The surface roughness over a serviced turbine airfoil is usually multi-scaled with varying features that are difficult to be universally characterized. However, it was previously discovered in low freestream turbulence conditions that the height of larger roughness produces separation and vortex shedding, which trigger early transition and exert a dominant effect on flow pattern and heat transfer. The geometry of the roughness and smaller roughness scales played secondary roles. This paper extends the previous study to elevated turbulence conditions with free-stream turbulence intensity ranging from 0.2–6.0 percent. A simplified test condition on a flat plate is conducted with two discrete regions having different surface roughness. The leading edge roughness is comprised of a sandpaper strip or a single cylinder. The downstream surface is either smooth or covered with sandpaper of grit sizes ranging from 100 ∼ 40 (Ra = 37 ∼ 119 μm). Hot wire measurements are conducted in the boundary layer to study the flow structure. The results of this study verify that the height of the largest-scale roughness triggers an earlier transition even under elevated turbulence conditions and exerts a more dominant effect on flow and heat transfer than does the geometry of the roughness. Heat transfer enhancements of about 30 ∼ 40 percent over the entire test surface are observed. The vortical motion, generated by the backward facing step at the joint of two roughness regions, is believed to significantly increase momentum transport across the boundary layer and bring the elevated turbulence from the freestream towards the wall. No such long-lasting heat transfer phenomenon is observed in low FSTI cases even though vortex shedding also exists in the low turbulence cases. The heat transfer enhancement decreases, instead of increases, as the downstream roughness height increases.

Effects of Weak Free Stream Nonuniformity on Boundary Layer Transition

2005 ◽  
Vol 128 (2) ◽  
pp. 247-257 ◽  
Author(s):  
Jonathan H. Watmuff
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Free Stream ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Bypass Transition ◽  
Mean Flow ◽  
Low Speed ◽  
Free Stream Turbulence ◽  
Thickness Variations

Experiments are described in which well-defined weak Free Stream Nonuniformity (FSN) is introduced by placing fine wires upstream of the leading edge of a flat plate. Large amplitude spanwise thickness variations form in the boundary layer as a result of the interaction between the steady laminar wakes from the wires and the leading edge. The centerline of a region of elevated layer thickness is aligned with the centerline of the wake in the freestream and the response is shown to be remarkably sensitive to the spanwise length-scale of the wakes. The region of elevated thickness is equivalent to a long narrow low speed streak in the layer. Elevated Free Stream Turbulence (FST) levels are known to produce randomly forming arrays of long narrow low speed streaks in laminar boundary layers. Therefore the characteristics of the streaks resulting from the FSN are studied in detail in an effort to gain some insight into bypass transition that occurs at elevated FST levels. The shape factors of the profiles in the vicinity of the streak appear to be unaltered from the Blasius value, even though the magnitude of the local thickness variations are as large as 60% of that of the undisturbed layer. Regions of elevated background unsteadiness appear on either side of the streak and it is shown that they are most likely the result of small amplitude spanwise modulation of the layer thickness. The background unsteadiness shares many of the characteristics of Klebanoff modes observed at elevated FST levels. However, the layer remains laminar to the end of the test section (Rx≈1.4×106) and there is no evidence of bursting or other phenomena associated with breakdown to turbulence. A vibrating ribbon apparatus is used to examine interactions between the streak and Tollmien-Schlichting (TS) waves. The deformation of the mean flow introduced by the streak is responsible for substantial phase and amplitude distortion of the waves and the breakdown of the distorted waves is more complex and it occurs at a lower Reynolds number than the breakdown of the K-type secondary instability that is observed when the FSN is not present.

Boundary layer development after a separated region

1998 ◽  
Vol 374 ◽  
pp. 91-116 ◽  
Author(s):  
IAN P. CASTRO ◽  
ELEANORA EPIK
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Free Stream ◽  
Turbulence Models ◽  
Separated Flow ◽  
Leading Edge ◽  
Turbulence Structure ◽  
Outer Flow ◽  
Free Stream Turbulence ◽  
Layer Region

Measurements obtained in boundary layers developing downstream of the highly turbulent, separated flow generated at the leading edge of a blunt flat plate are presented. Two cases are considered: first, when there is only very low (wind tunnel) turbulence present in the free-stream flow and, second, when roughly isotropic, homogeneous turbulence is introduced. With conditions adjusted to ensure that the separated region was of the same length in both cases, the flow around reattachment was significantly different and subsequent differences in the development rate of the two boundary layers are identified. The paper complements, but is much more extensive than, the earlier presentation of some of the basic data (Castro & Epik 1996), confirming not only that the development process is very slow, but also that it is non-monotonic. Turbulence stress levels fall below those typical of zero-pressure-gradient boundary layers and, in many ways, the boundary layer has features similar to those found in standard boundary layers perturbed by free-stream turbulence. It is argued that, at least as far as the turbulence structure is concerned, the inner layer region develops no more quickly than does the outer flow and it is the latter which essentially determines the overall rate of development of the whole flow. Some numerical computations are used to assess the extent to which current turbulence models are adequate for such flows.

Experiments in a boundary layer subjected to free stream turbulence. Part 2. The role of TS-waves in the transition process

1994 ◽  
Vol 281 ◽  
pp. 219-245 ◽  
Author(s):  
A. V. Boiko ◽  
K. J. A. Westin ◽  
B. G. B. Klingmann ◽  
V. V. Kozlov ◽  
P. H. Alfredsson
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Small Amplitude ◽  
Free Stream ◽  
Transition Process ◽  
Natural Occurrence ◽  
Free Stream Turbulence ◽  
Onset Of Turbulence ◽  
Tollmien Schlichting

The natural occurrence of Tollmien-Schlichting (TS) waves has so far only been observed in boundary layers subjected to moderate levels of free stream turbulence (Tu < 1%), owing to the difficulty in detecting small-amplitude waves in highly perturbed boundary layers. By introducing controlled oscillations with a vibrating ribbon, it is possible to study small-amplitude waves using phase-selective filtering techniques. In the present work, the effect of TS-waves on the transition is studied at Tu = 1.5%. It is demonstrated that TS-waves can exist and develop in a similar way as in an undisturbed boundary layer. It is also found that TS-waves with quite small amplitudes are involved in nonlinear interactions which lead to a regeneration of TS-waves in the whole unstable frequency band. This results in a significant increase in the number of turbulent spots, which promote the onset of turbulence.

Receptivity to free-stream vorticity of flow past a flat plate with elliptic leading edge

2010 ◽  
Vol 653 ◽  
pp. 245-271 ◽  
Author(s):  
L.-U. SCHRADER ◽  
L. BRANDT ◽  
C. MAVRIPLIS ◽  
D. S. HENNINGSON
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Free Stream ◽  
Three Dimensional ◽  
Low Frequency ◽  
Leading Edge ◽  
Sound Waves ◽  
Streamwise Vorticity ◽  
Low Frequencies ◽  
Free Stream Turbulence

Receptivity of the two-dimensional boundary layer on a flat plate with elliptic leading edge is studied by numerical simulation. Vortical perturbations in the oncoming free stream are considered, impinging on two leading edges with different aspect ratio to identify the effect of bluntness. The relevance of the three vorticity components of natural free-stream turbulence is illuminated by considering axial, vertical and spanwise vorticity separately at different angular frequencies. The boundary layer is most receptive to zero-frequency axial vorticity, triggering a streaky pattern of alternating positive and negative streamwise disturbance velocity. This is in line with earlier numerical studies on non-modal growth of elongated structures in the Blasius boundary layer. We find that the effect of leading-edge bluntness is insignificant for axial free-stream vortices alone. On the other hand, vertical free-stream vorticity is also able to excite non-modal instability in particular at zero and low frequencies. This mechanism relies on the generation of streamwise vorticity through stretching and tilting of the vertical vortex columns at the leading edge and is significantly stronger when the leading edge is blunt. It can thus be concluded that the non-modal boundary-layer response to a free-stream turbulence field with three-dimensional vorticity is enhanced in the presence of a blunt leading edge. At high frequencies of the disturbances the boundary layer becomes receptive to spanwise free-stream vorticity, triggering Tollmien–Schlichting (T-S) modes and receptivity increases with leading-edge bluntness. The receptivity coefficients to free-stream vortices are found to be about 15% of those to sound waves reported in the literature. For the boundary layers and free-stream perturbations considered, the amplitude of the T-S waves remains small compared with the low-frequency streak amplitudes.

Effects of Free Stream Turbulence on Intermittent Boundary Layer Flows

1995 ◽  
Author(s):  
Anestis I. Kalfas ◽  
Robin L. Elder
Keyword(s):  
Boundary Layer ◽  
Stream Flow ◽  
Free Stream ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Flow Transition ◽  
Flow Conditions ◽  
Boundary Layer Flows ◽  
Laminar Separation ◽  
Free Stream Turbulence

This paper considers the effects of free stream turbulence intensity on intermittent boundary layer flows related to turbomachinery. The present experimental investigation has been undertaken under free stream flow conditions dominated by grid generated turbulence and Reynolds numbers appropriate for turbomachinery applications. Unseparated flow transition in the boundary layer has been considered using a flat plate with the C4 leading edge which has been designed to avoid laminar separation. This configuration provided the opportunity to study the effect of a realistic turbomachinery leading edge shape on transition. Boundary layer type hot-wire probes have been used in order to acquire detailed information about the effect of the free stream conditions and the leading edge configuration on the structure of the boundary layer. Furthermore, information about the intermittency distribution throughout the boundary layer has been obtained using statistical analysis of the velocity record of the flow field.

Sign in / Sign up

Export Citation Format

Share Document