Nano structured TiO2 thin films in the efficient removal of b-estradiol from aqueous solution: physico-chemical studies

2019 ◽  
Vol 150 ◽  
pp. 263-273
Author(s):  
Alka Tiwari ◽  
Alok Shukla ◽  
Lalliansanga Lalliansanga ◽  
Diwakar Tiwari ◽  
Seung-Mok Lee
2018 ◽  
Vol 6 (1) ◽  
pp. 22-30
Author(s):  
C. Lalhriatpuia ◽  
◽  
Thanhming liana ◽  
K. Vanlaldinpuia

The photocatalytic activity of Nanopillars-TiO2 thin films was assessed in the degradation of Bromophenol blue (BPB) dye from aqueous solution under batch reactor operations. The thin films were characterized by the XRD, SEM and AFM analytical methods. BET specific surface area and pore sizes were also obtained. The XRD data showed anatase phase of TiO2 particles with average particle size of 25.4 and 21.9 nm, for S1 and S2 catalysts respectively. The SEM and AFM images indicated the catalyst composed with Nanosized pillars of TiO2, evenly distributed on the surface of the substrate. The average height of the pillars was found to be 180 and 40 nm respectively for the S1 and S2 catalyst. The BET specific surface area and pore sizes of S1 and S2 catalyst were found to be 5.217 and 1.420 m2/g and 7.77 and 4.16 nm respectively. The photocatalytic degradation of BPB using the UV light was studied at wide range of physico-chemical parametric studies to determine the mechanism of degradation as well as the practical applicability of the technique. The batch reactor operations were conducted at varied pH (pH 4.0 to 10.0), BPB initial concentration (1.0 to 20.0 mg/L) and presence of several interfering ions, i.e., cadmium nitrate, copper sulfate, zinc chloride, sodium chloride, sodium nitrate, sodium nitrite, glycine, oxalic acid and EDTA in the photocatalytic degradation of BPB. The maximum percent removal of BPB was observed at pH 6.0 and a low initial concentration of the pollutant highly favours the photocatalytic degradation using thin films. The presence of several interfering ions suppressed the photocatalytic activity of thin films to some extent. The time dependence photocatalytic degradation of BPB was demonstrated with the pseudo-first-order rate kinetics. Study was further extended with total organic carbon measurement using the TOC (Total Organic Carbon) analysis. This demonstrated an apparent mineralization of BPB from aqueous solutions.


2013 ◽  
Vol 5 (9) ◽  
pp. 3967-3974 ◽  
Author(s):  
Madhusmita Sahoo ◽  
Tom Mathews ◽  
Rajini P Antony ◽  
D. Nandagopala Krishna ◽  
S. Dash ◽  
...  

2002 ◽  
Vol 12 (9) ◽  
pp. 2643-2647 ◽  
Author(s):  
Yoshitake Masuda ◽  
Tsutomu Sugiyama ◽  
Kunihito Koumoto

2017 ◽  
Vol 79 (5-3) ◽  
Author(s):  
Siti Nur Hidayah Jaafar ◽  
Lorna Jeffery Minggu ◽  
Khuzaimah Arifin ◽  
Mohammad Kassim ◽  
Wan Ramli Wan Daud

Photoelectrochemical (PEC) water splitting is a very promising green method to produce solar fuel. Titanium dioxide (TiO2) has been widely used as photocatalyst for this type of reaction. Improving the performance of TiO2 for PEC water splitting has been ongoing and addition of sacrificial donor especially from waste is an attractive option to achieve this. Oxalic acid is one component in organic waste stream that can be used as sacrificial donor. The TiO2 thin films has been fabricated by coating TiO2 paste on Fluorine Tin oxide (FTO) glass surface. The morphology of the TiO2 thin films were porous and rough with uniform particles size with crystallite size of about 20 nm and dominant anatase peak. The TiO2 photoelectrode undergo PEC testing to measure its photolectroactivity by using oxalic acid as a sacrificial donor in two different type of electrolytes which are distilled water and sodium sulfate (NA2SO4) aqueous solution. The photocurrent produced without addition of oxalic acid is much lower than with the acid. The saturation photocurrent for aqueous NA2SO4 solution and water electrolyte is 0.1 mA/cm2 and negligible respectively. While the photocurrent for addition of oxalic acid in NA2SO4 aqueous solution is 0.5 mA/cm2 and the photocurrent for oxalic acid in water only is 0.9 mA/cm2, which is almost double compared to in NA2SO4 and tenfold in water only. The highest photocurrent produced by TiO2 photoelectrode is by addition of oxalic acid in aqueous (H2O) electrolyte.


Sign in / Sign up

Export Citation Format

Share Document