scholarly journals Urban aerosol number size distributions

2004 ◽  
Vol 4 (2) ◽  
pp. 391-411 ◽  
Author(s):  
T. Hussein ◽  
A. Puustinen ◽  
P. P. Aalto ◽  
J. M. Mäkelä ◽  
K. Hämeri ◽  
...  
Keyword(s):  
Particle Number ◽  
Size Range ◽  
Particle Diameter ◽  
Temporal Variations ◽  
Number Concentration ◽  
Building Construction ◽  
Urban Aerosol ◽  
Size Distributions ◽  
Arithmetic Means ◽  
Accumulation Mode

Abstract. Aerosol number size distributions have been measured since 5 May 1997 in Helsinki, Finland. The presented aerosol data represents size distributions within the particle diameter size range 8-400nm during the period from May 1997 to March 2003. The daily, monthly and annual patterns of the aerosol particle number concentrations were investigated. The temporal variation of the particle number concentration showed close correlations with traffic activities. The highest total number concentrations were observed during workdays; especially on Fridays, and the lowest concentrations occurred during weekends; especially Sundays. Seasonally, the highest total number concentrations were observed during winter and spring and lower concentrations were observed during June and July. More than 80% of the number size distributions had three modes: nucleation mode (Dp<30nm), Aitken mode (20-100nm) and accumulation mode (Dp>90nm). Less than 20% of the number size distributions had either two modes or consisted of more than three modes. Two different measurement sites were used; in the first (Siltavuori, 5.5.1997-5.3.2001), the arithmetic means of the particle number concentrations were 7000cm-3, 6500cm-3, and 1000cm-3 respectively for nucleation, Aitken, and accumulation modes. In the second site (Kumpula, 6.3.2001-28.2.2003) they were 5500cm-3, 4000cm-3, and 1000cm-3. The total number concentration in nucleation and Aitken modes were usually significantly higher during workdays than during weekends. The temporal variations in the accumulation mode were less pronounced. The lower concentrations at Kumpula were mainly due to building construction and also the slight overall decreasing trend during these years. During the site changing a period of simultaneous measurements over two weeks were performed showing nice correlation at both sites.

scholarly journals Urban aerosol number size distributions

2003 ◽  
Vol 3 (5) ◽  
pp. 5139-5184 ◽  
Author(s):  
T. Hussein ◽  
A. Puustinen ◽  
P. P. Aalto ◽  
J. M. Mäkelä ◽  
K. Hämeri ◽  
...  
Keyword(s):  
Particle Number ◽  
Number Concentration ◽  
Building Construction ◽  
Traffic Density ◽  
Urban Aerosol ◽  
Size Distributions ◽  
Accumulation Mode ◽  
Total Particle Number ◽  
Total Particle ◽  
Aitken Mode

Abstract. Aerosol number size distributions were measured continuously in Helsinki, Finland from 5 May 1997 to 28 February 2003. The daily, monthly and annual patterns were investigated. The temporal variation of the particle number concentration was seen to follow the traffic density. The highest total particle number concentrations were usually observed during workdays; especially on Fridays, and the lower concentrations occurred during weekends; especially Sundays. Seasonally, the highest total number concentrations were usually observed during winter and spring and the lowest during June and July. More than 80\\% of the particle number size distributions were tri-modal: nucleation mode (Dp < 30 nm), Aitken mode (20–100 nm) and accumulation mode (Dp > 90 nm). Less than 20% of the particle number size distributions have either two modes or consisted of more than three modes. Two different measurement sites are used; in the first place (Siltavuori, 5 May 1997–5 March 2001), the overall means of the integrated particle number concentrations were 7100 cm−3, 6320 cm−3, and 960 cm−3, respectively, for nucleation, Aitken, and accumulation modes. In the second site (Kumpula, 6 March 2001–28 February 2003) they were 5670 cm−3, 4050 cm−3, and 900 cm−3. The total number concentration in nucleation and Aitken modes were usually significantly higher during weekdays than during weekends. The variations in accumulation mode were less pronounced. The smaller concentrations in Kumpula were mainly due to building construction and also slight overall decreasing trend during these years. During the site changing a period of simultaneous measurements over two weeks were performed showing nice correlation in both sites.

scholarly journals Improving the simulation of global aerosol with size-segregated anthropogenic number emissions

2017 ◽  
Author(s):  
Filippo Xausa ◽  
Pauli Paasonen ◽  
Risto Makkonen ◽  
Mikhail Arshinov ◽  
Aijun Ding ◽  
...  
Keyword(s):  
Particle Number ◽  
Climate Models ◽  
Climate Model ◽  
Dominant Role ◽  
Particle Diameter ◽  
Radiation Budget ◽  
Size Distributions ◽  
Anthropogenic Aerosol ◽  
Accumulation Mode ◽  
Climate Interactions

Abstract. Climate models are important tools that are used for generating climate change projections, in which aerosol-climate interactions are one of the main sources of uncertainties. In order to quantify aerosol-radiation and aerosol-cloud interactions, detailed input of anthropogenic aerosol number emissions is necessary. However, the anthropogenic aerosol number emissions are usually converted from the corresponding mass emissions in precompiled emission inventories through a very simplistic method depending uniquely on chemical composition, particle size and density, which are defined for a few very wide main source sectors. In this work, the anthropogenic particle number emissions converted from the AeroCom mass in the ECHAM-HAM climate model were replaced with the recently-formulated number emissions from the Greenhouse Gas and Air Pollution Interactions and Synergies (GAINS)-model, where the emission number size distributions vary, for example, with respect to the fuel and technology. A special attention in our analysis was put on accumulation mode particles (particle diameter dp > 100 nm) because of (i) their capability of acting as cloud condensation nuclei (CCN), thus forming cloud droplets and affecting Earth's radiation budget, and (ii) their dominant role in forming the coagulation sink and thus limiting the concentration of sub-100 nanometers particles. In addition, the estimates of anthropogenic CCN formation, and thus the forcing from aerosol-climate interactions are expected to be affected. Analysis of global particle number concentrations and size distributions reveal that GAINS implementation increases CCN concentration compared with AeroCom, with regional enhancement factors reaching values as high as 10. A comparison between modeled and observed concentrations shows that the increase in number concentration for accumulation mode particle agrees well with measurements, but it leads to a consistent underestimation of both nucleation mode and Aitken mode (dp > 100 nm) particle number concentrations. This suggests that revisions are needed in the new particle formation and growth schemes currently applied in global modeling frameworks.

scholarly journals Advancing global aerosol simulations with size-segregated anthropogenic particle number emissions

2018 ◽  
Vol 18 (13) ◽  
pp. 10039-10054 ◽  
Author(s):  
Filippo Xausa ◽  
Pauli Paasonen ◽  
Risto Makkonen ◽  
Mikhail Arshinov ◽  
Aijun Ding ◽  
...  
Keyword(s):  
Particle Number ◽  
Climate Model ◽  
Dominant Role ◽  
Particle Diameter ◽  
Radiation Budget ◽  
Size Distributions ◽  
Anthropogenic Aerosol ◽  
Accumulation Mode ◽  
Climate Interactions ◽  
Gains Model

Abstract. Climate models are important tools that are used for generating climate change projections, in which aerosol–climate interactions are one of the main sources of uncertainties. In order to quantify aerosol–radiation and aerosol–cloud interactions, detailed input of anthropogenic aerosol number emissions is necessary. However, the anthropogenic aerosol number emissions are usually converted from the corresponding mass emissions in pre-compiled emission inventories through a very simplistic method depending uniquely on chemical composition, particle size and density, which are defined for a few, very wide main source sectors. In this work, the anthropogenic particle number emissions converted from the AeroCom mass in the ECHAM-HAM climate model were replaced with the recently formulated number emissions from the Greenhouse Gas and Air Pollution Interactions and Synergies (GAINS) model. In the GAINS model the emission number size distributions vary, for example, with respect to the fuel and technology. Special attention was paid to accumulation mode particles (particle diameter dp > 100 nm) because of (i) their capability of acting as cloud condensation nuclei (CCN), thus forming cloud droplets and affecting Earth's radiation budget, and (ii) their dominant role in forming the coagulation sink and thus limiting the concentration of sub-100 nm particles. In addition, the estimates of anthropogenic CCN formation, and thus the forcing from aerosol–climate interactions, are expected to be affected. Analysis of global particle number concentrations and size distributions reveals that GAINS implementation increases CCN concentration compared with AeroCom, with regional enhancement factors reaching values as high as 10. A comparison between modeled and observed concentrations shows that the increase in number concentration for accumulation mode particles agrees well with measurements, but it leads to a consistent underestimation of both nucleation mode and Aitken mode (dp < 100 nm) particle number concentrations. This suggests that revisions are needed in the new particle formation and growth schemes currently applied in global modeling frameworks.

scholarly journals On the seasonal variation in observed size distributions in northern Europe and their changes with decreasing anthropogenic emissions in Europe: climatology and trend analysis based on 17 years of data from Aspvreten, Sweden

2019 ◽  
Vol 19 (23) ◽  
pp. 14849-14873 ◽  
Author(s):  
Peter Tunved ◽  
Johan Ström
Keyword(s):  
Particle Number ◽  
Particle Formation ◽  
Number Concentration ◽  
Northern Europe ◽  
Anthropogenic Emissions ◽  
Particle Number Concentration ◽  
Size Distributions ◽  
Modal Number ◽  
Accumulation Mode ◽  
Aitken Mode

Abstract. Size-resolved aerosol trends were investigated based on a 17-year data set (2000–2017) from the rural background site Aspvreten located in southern Sweden (58.8∘ N, 17.4∘ E). Cluster analysis of the size distributions was performed to aid in the interpretation of the data. The results confirm previous findings of decreasing aerosol mass and number during the last decades as a result of reduced anthropogenic emissions in Europe. We show that both particle modal number concentration and size have substantially been reduced during the last 17 years. Negative trends in particle number concentration of about 10 cm−3 yr−1 are present for nuclei, Aitken, and accumulation modes. In total, integral particle number concentration has decreased by 30 %, from 1860 to ca. 1300 cm−3. The reduction in modal number concentration is accompanied by a decrease in modal size, and this decrease is largest for the accumulation mode (2 nm yr−1 or about 17 % for the whole period). These reductions have resulted in a decrease in submicron particle mass (< 390 nm) by more than 50 % over the period 2000–2017. These decreases are similar to observations found at other stations in northern Europe. Although all size classes show a downward trend as annual averages, we also show that observed trends are not evenly distributed over the year and that a rather complex picture emerges where both sign and magnitude of trends vary with season and size. The strongest negative trends are present during spring (accumulation mode) and autumn (Aitken mode). The strongest positive trends are present during summer months (Aitken mode). The combined trajectory and data analyses do not present evidence for an increase in new particle formation formed locally, although some evidence of increased new particle formation some distance away from the receptor is present. Observed aerosol size distribution data, together with an adiabatic cloud parcel model, were further used to estimate the change in cloud droplet concentration for various assumptions of updraught velocities and aerosol chemical composition. The results indicate a substantial increase in the atmospheric brightening effect due to a reduction in cloud reflectivity corresponding to 10 %–12 % reduction in cloud albedo over the period 2000–2017.

scholarly journals Fluorescent biological aerosol particle concentrations and size distributions measured with an Ultraviolet Aerodynamic Particle Sizer (UV-APS) in Central Europe

2010 ◽  
Vol 10 (7) ◽  
pp. 3215-3233 ◽  
Author(s):  
J. A. Huffman ◽  
B. Treutlein ◽  
U. Pöschl
Keyword(s):  
Particle Number ◽  
Fungal Spores ◽  
Number Concentration ◽  
Size Distributions ◽  
Bacterial Cells ◽  
Spores And Pollen ◽  
Measurement Results ◽  
The Mean ◽  
Particle Sizer ◽  
Biological Aerosol Particles

Abstract. Primary Biological Aerosol Particles (PBAPs), including bacteria, spores and pollen, are essential for the spread of organisms and disease in the biosphere, and numerous studies have suggested that they may be important for atmospheric processes, including the formation of clouds and precipitation. The atmospheric abundance and size distribution of PBAPs, however, are largely unknown. At a semi-urban site in Mainz, Germany we used an Ultraviolet Aerodynamic Particle Sizer (UV-APS) to measure Fluorescent Biological Aerosol Particles (FBAPs), which provide an estimate of viable bioaerosol particles and can be regarded as an approximate lower limit for the actual abundance of PBAPs. Fluorescence of non-biological aerosol components are likely to influence the measurement results obtained for fine particles (<1 μm), but not for coarse particles (1–20 μm). Averaged over the four-month measurement period (August–December 2006), the mean number concentration of coarse FBAPs was ~3×10−2 cm−3, corresponding to ~4% of total coarse particle number. The mean mass concentration of FBAPs was ~1μg m−3, corresponding to ~20% of total coarse particle mass. The FBAP number size distributions exhibited alternating patterns with peaks at various diameters. A pronounced peak at ~3 μm was essentially always observed and can be described by the following campaign-average lognormal fit parameters: geometric mean diameter 3.2 μm, geometric standard deviation 1.3, number concentration 1.6×10−2 cm−3. This peak is likely due to fungal spores or agglomerated bacteria, and it exhibited a pronounced diel cycle (24-h) with maximum intensity during early/mid-morning. FBAP peaks around ~1.5 μm, ~5 μm, and ~13 μm were also observed, but less pronounced and less frequent. These may be single bacterial cells, larger fungal spores, and pollen grains, respectively. The observed number concentrations and characteristic sizes of FBAPs are consistent with microscopic, biological and chemical analyses of PBAPs in aerosol filter samples. To our knowledge, however, this is the first exploratory study reporting continuous online measurements of bioaerosol particles over several months and a range of characteristic size distribution patterns with a persistent bioaerosol peak at ~3 μm. The measurement results confirm that PBAPs account for a substantial proportion of coarse aerosol particle number and mass in continental boundary layer air. Moreover, they suggest that the number concentration of viable bioparticles is dominated by fungal spores or agglomerated bacteria with aerodynamic diameters around 3 μm rather than single bacterial cells with diameters around 1 μm.

scholarly journals Cloud activation properties of aerosol particles in a continental Central European urban environment

2021 ◽  
Vol 21 (14) ◽  
pp. 11289-11302
Author(s):  
Imre Salma ◽  
Wanda Thén ◽  
Máté Vörösmarty ◽  
András Zénó Gyöngyösi
Keyword(s):  
Chemical Composition ◽  
Particle Number ◽  
Cloud Condensation Nuclei ◽  
Aerosol Particles ◽  
Number Concentration ◽  
Urban Aerosol ◽  
Condensation Nuclei ◽  
Frequency Distributions ◽  
Remote Locations ◽  
Cloud Activation

Abstract. Collocated measurements using a condensation particle counter, differential mobility particle sizer and cloud condensation nuclei counter were realised in parallel in central Budapest from 15 April 2019 to 14 April 2020 to gain insight into the cloud activation properties of urban aerosol particles. The median total particle number concentration was 10.1 × 103 cm−3. The median concentrations of cloud condensation nuclei (CCN) at water vapour supersaturation (S) values of 0.1 %, 0.2 %, 0.3 %, 0.5 % and 1.0 % were 0.59, 1.09, 1.39, 1.80 and 2.5 × 103 cm−3, respectively. The CCN concentrations represented 7–27 % of all particles. The CCN concentrations were considerably larger but the activation fractions were systematically substantially smaller than observed in regional or remote locations. The effective critical dry particle diameters (dc,eff) were derived utilising the CCN concentrations and particle number size distributions. Their median values at the five supersaturation values considered were 207, 149, 126, 105 and 80 nm, respectively; all of these diameters were positioned within the accumulation mode of the typical particle number size distribution. Their frequency distributions revealed a single peak for which the geometric standard deviation increased monotonically with S. This broadening indicated high time variability in the activating properties of smaller particles. The frequency distributions also showed fine structure, with several compositional elements that seemed to reveal a consistent or monotonical tendency with S. The relationships between the critical S and dc,eff suggest that urban aerosol particles in Budapest with diameters larger than approximately 130 nm showed similar hydroscopicity to corresponding continental aerosol particles, whereas smaller particles in Budapest were less hygroscopic than corresponding continental aerosol particles. Only modest seasonal cycling in CCN concentrations and activation fractions was seen, and only for large S values. This cycling likely reflects changes in the number concentration, chemical composition and mixing state of the particles. The seasonal dependencies of dc,eff were featureless, indicating that the droplet activation properties of the urban particles remained more or less the same throughout the year. This is again different from what is seen in non-urban locations. Hygroscopicity parameters (κ values) were computed without determining the time-dependent chemical composition of the particles. The median values for κ were 0.15, 0.10, 0.07, 0.04 and 0.02, respectively, at the five supersaturation values considered. The averages suggested that the larger particles were considerably more hygroscopic than the smaller particles. We found that the κ values for the urban aerosol were substantially smaller than those previously reported for aerosols in regional or remote locations. All of these characteristics can be linked to the specific source composition of particles in cities. The relatively large variability in the hygroscopicity parameters for a given S emphasises that the individual values represent the CCN population in ambient air while the average hygroscopicity parameter mainly corresponds to particles with sizes close to the effective critical dry particle diameter.

scholarly journals Urban aerosol size distributions over the Mediterranean city of Barcelona, NE Spain

2012 ◽  
Vol 12 (7) ◽  
pp. 16457-16492 ◽  
Author(s):  
M. Dall'Osto ◽  
D.C.S. Beddows ◽  
J. Pey ◽  
S. Rodriguez ◽  
A. Alastuey ◽  
...  
Keyword(s):  
Particle Number ◽  
Number Concentration ◽  
Aerosol Size Distribution ◽  
Time Variability ◽  
Small Contribution ◽  
Particle Number Concentration ◽  
Size Distributions ◽  
Total Particle Number ◽  
Total Particle ◽  
One Year

Abstract. Differential mobility particle sizer (DMPS) aerosol concentrations (N13–800) were collected over a one-year-period (2004) at an urban background site in Barcelona, North-Eastern Spain. Quantitative contributions to particle number concentrations of the nucleation (33–38%), Aitken (39–49%) and accumulation mode (18–22%) were estimated. We examined the source and time variability of atmospheric aerosol particles by using both K-means clustering and Positive Matrix Factorization (PMF) analysis. Performing clustering analysis on hourly size distributions, nine K-means DMPS clusters were identified and, by directional association, diurnal variation and relationship to meteorological and pollution variables, four typical aerosol size distribution scenarios were identified: traffic (69% of the time), dilution (15% of the time), summer background conditions (4% of the time) and regional pollution (12% of the time). According to the results of PMF, vehicle exhausts are estimated to contribute at least to 62–66% of the total particle number concentration, with a slightly higher proportion distributed towards the nucleation mode (34%) relative to the Aitken mode (28–32%). Photochemically induced nucleation particles make only a small contribution to the total particle number concentration (2–3% of the total), although only particles larger than 13 nm were considered in this study. Overall the combination of the two statistical methods is successful at separating components and quantifying relative contributions to the particle number population.

scholarly journals Long-Term Characterization of Submicron Atmospheric Particles in an Urban Background Site in Southern Italy

Atmosphere ◽  
2020 ◽  
Vol 11 (4) ◽  
pp. 334 ◽  
Author(s):  
Adelaide Dinoi ◽  
Marianna Conte ◽  
Fabio M. Grasso ◽  
Daniele Contini
Keyword(s):  
Particle Number ◽  
Meteorological Parameters ◽  
Particle Diameter ◽  
Number Concentration ◽  
Total Particle Number ◽  
Total Particle ◽  
Late Evening ◽  
20 Nm

Continuous measurements of particle number size distributions in the size range from 10 nm to 800 nm were performed from 2015 to 2019 at the ECO Environmental-Climate Observatory of Lecce (Global Atmosphere Watch Programme/Aerosol, Clouds and Trace Gases Research Infrastructure (GAW/ACTRIS) regional station). The main objectives of this work were to investigate the daily, weekly and seasonal trends of particle number concentrations and their dependence on meteorological parameters gathering information on potential sources. The highest total number concentrations were observed during autumn-winter with average values nearly twice as high as in summer. More than 52% of total particle number concentration consisted of Aitken mode (20 nm < particle diameter (Dp) < 100 nm) particles followed by accumulation (100 nm < Dp < 800 nm) and nucleation (10 nm < Dp < 20 nm) modes representing, respectively, 27% and 21% of particles. The total number concentration was usually significantly higher during workdays than during weekends/holidays in all years, showing a trend likely correlated with local traffic activities. The number concentration of each particle mode showed a characteristic daily variation that was different in cold and warm seasons. The highest concentrations of the Aitken and accumulation particle mode were observed in the morning and the late evening, during typical rush hour traffic times, highlighting that the two-particle size ranges are related, although there was significant variation in the number concentrations. The peak in the number concentrations of the nucleation mode observed in the midday of spring and summer can be attributed to the intensive formation of new particles from gaseous precursors. Based on Pearson coefficients between particle number concentrations and meteorological parameters, temperature, and wind speed had significant negative relationships with the Aitken and accumulation particle number concentrations, whereas relative humidity was positively correlated. No significant correlations were found for the nucleation particle number concentrations.

scholarly journals Multi-year statistical and modelling analysis of submicrometer aerosol number size distributions at a rain forest site in Amazonia

2018 ◽  
Author(s):  
Luciana Varanda Rizzo ◽  
Pontus Roldin ◽  
Joel Brito ◽  
John Backman ◽  
Erik Swietlicki ◽  
...  
Keyword(s):  
Particle Size ◽  
Rain Forest ◽  
Amazon Basin ◽  
Particle Number ◽  
Dry Season ◽  
Forest Site ◽  
Size Distributions ◽  
Wet Season ◽  
Accumulation Mode ◽  
Aitken Mode

Abstract. The Amazon Basin is a unique region to study atmospheric aerosols, given their relevance for the regional hydrological cycle and large uncertainty of their sources. Multi-year datasets are crucial when contrasting periods of natural conditions and periods influenced by anthropogenic emissions. In the wet season, biogenic sources and processes prevail, and the Amazonian atmospheric composition resembles pre-industrial conditions. In the dry season, the Basin is influenced by widespread biomass burning emissions. This work reports multi-year observations of high time resolution submicrometer (10–600 nm) particle number size distributions at a rain forest site in Amazonia (TT34 tower, 60 km NW from Manaus city), between years 2008–2010 and 2012–2014. Median particle number concentration was 403 cm−3 in the wet season and 1254 cm−3 in the dry season. The Aitken mode (~ 30–100 nm in diameter) was prominent during the wet season, while accumulation mode (~ 100–600 nm in diameter) dominated the particle size spectra during the dry season. Cluster analysis identified groups of aerosol number size distribution influenced by convective downdrafts, nucleation events and fresh biomass burning emissions. New particle formation and subsequent growth was rarely observed during the 749 days of observations, similar to previous observations in the Amazon Basin. A stationary 1D column model (ADCHEM – Aerosol Dynamics, gas and particle phase CHEMistry and radiative transfer model) was used to assess importance of processes behind the observed diurnal particle size distribution trends. Three major particle source types are required in the model to reproduce the observations: (i) a surface source of particles in the evening, possibly related to primary biological emissions (ii) entrainment of accumulation mode aerosols in the morning, and (iii) convective downdrafts transporting Aitken mode particles into the boundary layer mostly during the afternoon. The latter process has the largest influence on the modelled particle number size distributions. However, convective downdrafts are often associated with rain and thus act both as a source of Aitken mode particles, and as a sink of accumulation mode particles, causing a net reduction in the median total particle number concentrations in the surface layer. Our study shows that the combination of the three mentioned particle sources are essential to sustain particle number concentrations in Amazonia.

Characterization of Particle Size, Number, and Mass Emissions From a Diesel Powered Generator

2006 ◽  
Author(s):  
Imad A. Khalek
Keyword(s):  
Particle Size ◽  
Solid Particle ◽  
Particle Distribution ◽  
Size Range ◽  
Number Concentration ◽  
Solid Particles ◽  
Size Distributions ◽  
Particle Size Distributions ◽  
Engine Operation ◽  
Size Number

Total (volatile plus solid) and solid particle size, number, and mass emitted from a 3.8 kW diesel powered generator were characterized using a Scanning Mobility Particle Sizer (SMPS) that measures the size distribution of particles, and a catalytic stripper that facilitates the measurement of solid particles. The engine was operated at a constant speed for six steady-state engine operations ranging from idle to rated power. The solid particle size distributions were mainly monomodal lognormal distributions in nature reflecting a typical soot agglomerate size distribution with a number mean diameter in the size range from 98 nm to 37 nm as the load decreases from high to low. At idle, M6, however, the solid particle distribution was bimodal in nature with a high number of solid nanoparticles in the sub-20 nm size range. It is likely that these solid particles nucleated later in the combustion process from metallic ash typically present in the lube oil. The total particle size distributions exhibited a bimodal structure only at light load, M5, engine operation, where a high number of volatile nanoparticles were observed. The rest of the operating conditions exhibited monomodal distributions although the nature of the particles was vastly different. For the medium load modes, M2, M3, and M4, the particles were mainly solid particles. For the rated power, M1, and idle, M6, modes of engine operation, significant number of volatile particles grew to a size nearing that of soot particles making the distribution monomodal, similar to that of a solid particle distribution. This shows that monomodal distributions are not necessarily solid particle but they can be strongly dominated with volatile particles if significant particle growth takes place like the case at M1, and M6. The total number and mass concentration were extremely high at engine rated power. The number concentration exceeded 1.2 billion particles per cubic centimeter and the mass exceeded 750 milligrams per cubic meter. The number concentration is more than five orders of magnitude higher than a typical ambient level concentration, and the mass concentration is more than four orders of magnitude higher. It is important to indicate, however, that if the engine power rating is lowered by 35 percent from its designated level, both particle mass and number emissions will be reduced by two orders of magnitude. By measuring total and solid particle size and number concentration of particles, one can calculate other metrics such as surface area and mass to provide detail information about particle emissions. Such information can serve as an important database where all metrics of particle emissions are captured.

Sign in / Sign up

Export Citation Format

Share Document