scholarly journals Frictional properties and microstructural evolution of dry and wet calcite–dolomite gouges

Solid Earth ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 595-612
Author(s):  
Matteo Demurtas ◽  
Steven A.F. Smith ◽  
Elena Spagnuolo ◽  
Giulio Di Toro

Abstract. Calcite and dolomite are the two most common minerals in carbonate-bearing faults and shear zones. Motivated by observations of exhumed seismogenic faults in the Italian Central Apennines, we used a rotary-shear apparatus to investigate the frictional and microstructural evolution of ca. 3 mm thick gouge layers consisting of 50 wt % calcite and 50 wt % dolomite. The gouges were sheared at a range of slip rates (30 µm s−1–1 m s−1), displacements (0.05–0.4 m), and a normal load of 17.5 MPa under both room-humidity and water-dampened conditions. The frictional behaviour and microstructural evolution of the gouges were strongly influenced by the presence of water. At room humidity, slip strengthening was observed up to slip rates of 0.01 m s−1, which was associated with gouge dilation and the development of a 500–900 µm wide slip zone cut by Y-, R-, and R1-shear bands. Above a slip rate of 0.1 m s−1, dynamic weakening accompanied the development of a localised < 100 µm thick principal slip zone preserving microstructural evidence for calcite recrystallisation and dolomite decarbonation, while the bulk gouges developed a well-defined foliation consisting of organised domains of heavily fractured calcite and dolomite. In water-dampened conditions, evidence of gouge fluidisation within a fine-grained principal slip zone was observed at a range of slip rates from 30 µm s−1 to 0.1 m s−1, suggesting that caution is needed when relating fluidisation textures to seismic slip in natural fault zones. Dynamic weakening in water-dampened conditions was observed at 1 m s−1, where the principal slip zone was characterised by patches of recrystallised calcite. However, local fragmentation and reworking of recrystallised calcite suggests a cyclic process involving formation and destruction of a heterogeneous slip zone. Our microstructural data show that development of well-defined gouge foliation under the tested experimental conditions is limited to high velocities (>0.1 m s−1) and room humidity, supporting the notion that some foliated gouges and cataclasites may form during seismic slip in natural carbonate-bearing faults.

2020 ◽  
Author(s):  
Matteo Demurtas ◽  
Steven A.F. Smith ◽  
Elena Spagnuolo ◽  
Giulio Di Toro

Abstract. Calcite and dolomite are the two most common minerals in carbonate-bearing faults and shear zones. Motivated by field examples from exhumed seismogenic faults in the Italian Central Apennines, we investigated the frictional and microstructural evolution of gouge mixtures consisting of 50 wt % calcite and 50 wt % dolomite using a rotary-shear apparatus. The gouges were sheared at a range of slip rates (30 µm s−1–1 m s−1), displacements (0.05–0.4 m), and normal loads (17.5–26 MPa), under both room humidity and water-dampened conditions. The frictional behaviour and microstructural evolution of the gouges were strongly influenced by the presence of water. At room humidity, slip strengthening behaviour was observed up to slip rates of 0.01 m s−1, which was associated with gouge dilation and the development of a 500–900 µm wide slip zone cut by Y-, R-, and R1-shear bands. Above a slip rate of 0.1 m s−1, dynamic weakening accompanied the development of a localised <100 µm thick principal slip zone preserving microstructural evidence for calcite recrystallization and dolomite decarbonation, while the bulk gouges developed a well-defined foliation consisting of organized domains of heavily fractured calcite and dolomite. In water-dampened conditions, evidence of gouge fluidization within a fine-grained principal slip zone was observed at a wide range of slip-rates from 30 µm s−1 to 0.1 m s−1, suggesting that caution is needed when relating fluidization textures to seismic slip in natural fault zones. Dynamic weakening in water-dampened conditions was observed at 1 m s−1, where the principal slip zone was characterised by patches of recrystallized calcite. However, local fragmentation and reworking of recrystallized calcite suggests a cyclic process involving formation and destruction of a heterogeneous slip zone. Our microstructural data show that development of a well-defined gouge foliation at these experimental conditions is limited to high-velocity (>0.1 m s−1) and room humidity, supporting the notion that some foliated gouges and cataclasites may form during seismic slip in natural carbonate-bearing faults.


Geology ◽  
2020 ◽  
Vol 48 (5) ◽  
pp. 514-518 ◽  
Author(s):  
Gabriele Calzolari ◽  
Alexis K. Ault ◽  
Greg Hirth ◽  
Robert G. McDermott

Abstract Evidence for coseismic temperature rise that induces dynamic weakening is challenging to directly observe and quantify in natural and experimental fault rocks. Hematite (U-Th)/He (hematite He) thermochronometry may serve as a fault-slip thermometer, sensitive to transient high temperatures associated with earthquakes. We test this hypothesis with hematite deformation experiments at seismic slip rates, using a rotary-shear geometry with an annular ring of silicon carbide (SiC) sliding against a specular hematite slab. Hematite is characterized before and after sliding via textural and hematite He analyses to quantify He loss over variable experimental conditions. Experiments yield slip surfaces localized in an ∼5–30-µm-thick layer of hematite gouge with &lt;300-µm-diameter fault mirror (FM) zones made of sintered nanoparticles. Hematite He analyses of undeformed starting material are compared with those of FM and gouge run products from high-slip-velocity experiments, showing &gt;71% ± 1% (1σ) and 18% ± 3% He loss, respectively. Documented He loss requires short-duration, high temperatures during slip. The spatial heterogeneity and enhanced He loss from FM zones are consistent with asperity flash heating (AFH). Asperities &gt;200–300 µm in diameter, producing temperatures &gt;900 °C for ∼1 ms, can explain observed He loss. Results provide new empirical evidence describing AFH and the role of coseismic temperature rise in FM formation. Hematite He thermochronometry can detect AFH and thus seismicity on natural FMs and other thin slip surfaces in the upper seismogenic zone of Earth’s crust.


2014 ◽  
Vol 119 (11) ◽  
pp. 8107-8131 ◽  
Author(s):  
B. P. Proctor ◽  
T. M. Mitchell ◽  
G. Hirth ◽  
D. Goldsby ◽  
F. Zorzi ◽  
...  

2016 ◽  
Vol 121 (10) ◽  
pp. 7490-7513 ◽  
Author(s):  
François. X. Passelègue ◽  
Elena Spagnuolo ◽  
Marie Violay ◽  
Stefan Nielsen ◽  
Giulio Di Toro ◽  
...  

Author(s):  
Arjun H. Kohli ◽  
David L. Goldsby ◽  
Greg Hirth ◽  
Terry Tullis
Keyword(s):  

2008 ◽  
Vol 269 (1-2) ◽  
pp. 131-139 ◽  
Author(s):  
Lidia Pittarello ◽  
Giulio Di Toro ◽  
Andrea Bizzarri ◽  
Giorgio Pennacchioni ◽  
Jafar Hadizadeh ◽  
...  

Author(s):  
Luca Menegon ◽  
Lucy Campbell ◽  
Neil Mancktelow ◽  
Alfredo Camacho ◽  
Sebastian Wex ◽  
...  

This paper discusses the results of field-based geological investigations of exhumed rocks exposed in the Musgrave Ranges (Central Australia) and in Nusfjord (Lofoten, Norway) that preserve evidence for lower continental crustal earthquakes with focal depths of approximately 25–40 km. These studies have established that deformation of the dry lower continental crust is characterized by a cyclic interplay between viscous creep (mylonitization) and brittle, seismic slip associated with the formation of pseudotachylytes (a solidified melt produced during seismic slip along a fault in silicate rocks). Seismic slip triggers rheological weakening and a transition to viscous creep, which may be already active during the immediate post-seismic deformation along faults initially characterized by frictional melting and wall-rock damage. The cyclical interplay between seismic slip and viscous creep implies transient oscillations in stress and strain rate, which are preserved in the shear zone microstructure. In both localities, the spatial distribution of pseudotachylytes is consistent with a local (deep) source for the transient high stresses required to generate earthquakes in the lower crust. This deep source is the result of localized stress amplification in dry and strong materials generated at the contacts with ductile shear zones, producing multiple generations of pseudotachylyte over geological time. This implies that both the short- and the long-term rheological evolution of the dry lower crust typical of continental interiors is controlled by earthquake cycle deformation. This article is part of a discussion meeting issue ‘Understanding earthquakes using the geological record’.


2020 ◽  
Author(s):  
Arnab Roy ◽  
Nandan Roy ◽  
Puspendu Saha ◽  
Nibir Mandal

&lt;p&gt;Development of brittle and brittle-ductile shear zones involve partitioning of large shear strains in bands, called C-shear bands (C-SB) nearly parallel to the shear zone boundaries. Our present work aims to provide a comprehensive understanding of the rheological factors in controlling such SB growth in meter scale natural brittle- ductile shear zones observed in in Singbhum and Chotonagpur mobile belts.&amp;#160; The shear zones show C- SB at an angle of 0&amp;#176;- 5&amp;#176; with the shear zone boundary. We used analogue models, based on Coulomb and Viscoplastic rheology to reproduce them in experimental conditions.&lt;/p&gt;&lt;p&gt;These models produce dominantly Riedel (R) shear bands. We show a transition from R-shearing in conjugate to single sets at angles of ~15&lt;sup&gt;o&lt;/sup&gt; by changing model materials. However, none of the analogue models produced C-SB, as observed in the field. To reconcile the experimental and field findings, numeral models have been used to better constrain the geometrical and rheological parameters. We simulate model shear zones replicating those observed in the field, which display two distinct zones: drag zone where the viscous strains dominate &amp;#160;and the core zone, where both viscous and plastic strains come into play. &amp;#160;Numerical model results suggest the formation of &amp;#160;C- SB for a specific rheological condition. We also show varying shear band patterns as a function of the thickness ratio between drag and core zones.&lt;/p&gt;


Sign in / Sign up

Export Citation Format

Share Document