scholarly journals A SYSTEM FOR MEASUREMENTS OF 3D SCANNED ORTHODONTIC STUDY MODELS

2017 ◽  
Vol 8 (2) ◽  
Author(s):  
Marijana Arapović Savić ◽  
Mihajlo Savić ◽  
Adriana Arbutina ◽  
Mirjana Umićević Davidović ◽  
Vladan Mirjanić
Keyword(s):  
3D Models ◽  
Therapy Planning ◽  
Digital Models ◽  
Web Based ◽  
Diagnosis Therapy ◽  
Web Based System ◽  
Dental Casts

Plaster dental casts represent an important item in the process of diagnosis, therapy planning and documenting, both in orthodontics, as well as other areas of dentistry. Dental casts allow us to track occlusal contacts before the therapy as well as the changes during the growth and therapy. Although they do possess many positive features, due to the rapid advancements in technology, their negative sides have became more prominent leading to the more widespread use of digital 3D models as their replacement. In this paper, we present a web based system that allows us, after the casts have been scanned, to produce easily usable digital models, to store them and perform measurements on them. Performed measurements are suitable for futher processing and analysis.

Rancang Bangun Sistem Penerimaan Dan Mutasi Barang Pada PDAM Tirta Kerta Raharja

Sensi Journal ◽  
2020 ◽  
Vol 6 (2) ◽  
pp. 236-246
Author(s):  
Ilamsyah Ilamsyah ◽  
Yulianto Yulianto ◽  
Tri Vita Febriani
Keyword(s):  
System Analysis ◽  
Object Oriented ◽  
Analysis Method ◽  
Web Based ◽  
Visual Modeling ◽  
Long Time ◽  
The Right ◽  
And Control ◽  
Web Based System ◽  
The Web

The right and appropriate system of receiving and transferring goods is needed by the company. In the process of receiving and transferring goods from the central warehouse to the branch warehouse at PDAM Tirta Kerta Raharja, Tangerang Regency, which is currently done manually is still ineffective and inaccurate because the Head of Subdivision uses receipt documents, namely PPBP and mutation of goods, namely MPPW in the form of paper as a submission media. The Head of Subdivision enters the data of receipt and mutation of goods manually and requires a relatively long time because at the time of demand for the transfer of goods the Head of Subdivision must check the inventory of goods in the central warehouse first. Therefore, it is necessary to hold a design of information systems for the receipt and transfer of goods from the central warehouse to a web-based branch warehouse that is already database so that it is more effective, efficient and accurate. With the web-based system of receiving and transferring goods that are already datatabed, it can facilitate the Head of Subdivision in inputing data on the receipt and transfer of goods and control of stock inventory so that the Sub Head of Subdivision can do it periodically to make it more effective, efficient and accurate. The method of data collection is done by observing, interviewing and studying literature from various previous studies, while the system analysis method uses the Waterfall method which aims to solve a problem and uses design methods with visual modeling that is object oriented with UML while programming using PHP and MySQL as a database.

scholarly journals Comparative Analysis of Digital Models of Objects of Cultural Heritage Obtained by the “3D SLS” and “SfM” Methods

2021 ◽  
Vol 11 (12) ◽  
pp. 5321
Author(s):  
Marcin Barszcz ◽  
Jerzy Montusiewicz ◽  
Magdalena Paśnikowska-Łukaszuk ◽  
Anna Sałamacha
Keyword(s):  
Cultural Heritage ◽  
Low Cost ◽  
Three Dimensional ◽  
3D Models ◽  
Silk Road ◽  
Digital Models ◽  
Global Pandemic ◽  
University Of Technology ◽  
Three Dimensional Models ◽  
3D Digitisation

In the era of the global pandemic caused by the COVID-19 virus, 3D digitisation of selected museum artefacts is becoming more and more frequent practice, but the vast majority is performed by specialised teams. The paper presents the results of comparative studies of 3D digital models of the same museum artefacts from the Silk Road area generated by two completely different technologies: Structure from Motion (SfM)—a method belonging to the so-called low-cost technologies—and by Structured-light 3D Scanning (3D SLS). Moreover, procedural differences in data acquisition and their processing to generate three-dimensional models are presented. Models built using a point cloud were created from data collected in the Afrasiyab museum in Samarkand (Uzbekistan) during “The 1st Scientific Expedition of the Lublin University of Technology to Central Asia” in 2017. Photos for creating 3D models in SfM technology were taken during a virtual expedition carried out under the “3D Digital Silk Road” program in 2021. The obtained results show that the quality of the 3D models generated with SfM differs from the models from the technology (3D SLS), but they may be placed in the galleries of the vitrual museum. The obtained models from SfM do not have information about their size, which means that they are not fully suitable for archiving purposes of cultural heritage, unlike the models from SLS.

The Combat Experience Log: A web-based system for the in theater assessment of war zone stress

2011 ◽  
Vol 25 (6) ◽  
pp. 794-800 ◽  
Author(s):  
Han-Joo Lee ◽  
Katy Goudarzi ◽  
Brian Baldwin ◽  
David Rosenfield ◽  
Michael J. Telch
Keyword(s):  
Combat Experience ◽  
Web Based ◽  
War Zone ◽  
Web Based System

Usability of Web-Based Design and Manufacturing Systems: Case Study of Micro Machining

2005 ◽  
Author(s):  
Hyung-Jung Kim ◽  
Won-Shik Chu ◽  
Hyuk-Jin Kang ◽  
Sung-Hoon Ahn ◽  
Dong-Soo Kim ◽  
...  
Keyword(s):  
Manufacturing Systems ◽  
Processing Time ◽  
Micro Machining ◽  
User Friendliness ◽  
Web Based ◽  
Design And Manufacturing ◽  
Cad Cam ◽  
Machining System ◽  
Web Based System ◽  
The Web

In this paper, web-based design and manufacturing systems are compared with a commercial CAD/CAM system from the point of usability. The web-based systems included in this study were MIcro Machining System (MIMS) and SmartFab. In the MIMS architecture, a 3D model in STL format was read via a web browser, sent to the web server for toolpath planning, and NC codes were generated to be fed back to the designer through the web connection. In the SmartFab system, SolidWorks was used as the design interface with provided modified menus for micro machining. These additional menus were created by SolidWorks API that also provided web-based links to the toolpath planner. In the commercial CAD/CAM case, without using any web connection, SolidWorks or CATIA was used for design, and PowerMill was used as a CAM tool. For each design and manufacturing system, accessibility, user-friendliness, toolpath-reliability, and processing time were compared. Total 91 students tested these systems in undergraduate CAD class, and the feedback showed better performance of the web-based system in accessibility, user-friendliness, and processing time. However, reliability of the web-based system showed necessity of further improvement.

Sign in / Sign up

Export Citation Format

Share Document