Estimation of Minimum Uncut Chip Thickness during Precision and Micro-Machining Processes of Various Materials—A Critical Review

Evaluation of the phenomena characterizing the chip decohesion process during cutting is still a current problem in relation to precision, ultra-precision, and micro-machining processes of construction materials. The reliable estimation of minimum uncut chip thickness is an especially challenging task since it directly affects the machining process dynamics and formation of a surface topography. Therefore, in this work a critical review of the recent studies concerning the determination of minimum uncut chip thickness during precision, ultra-precision, and micro-cutting is presented. The first part of paper covers a characterization of the precision, ultra-precision, and micro-cutting processes. In the second part, the analytical, experimental, and numerical methods for minimum uncut chip thickness estimation are presented in detail. Finally, a summary of the research results for minimum uncut chip thickness estimation is presented, together with conclusions and a determination of further research directions.

Effect of Machining Limiting Factors on Drilling Progress during Spark Assisted Chemical Engraving (SACE): General Trends

Spark Assisted Chemical Engraving (SACE) is a micro-machining technology for non-conductive materials, mainly glass, based on thermal assisted etching. Generally, during SACE, drilling proceeds at a fast rate reaching 100 µm/s for the first 100 µm and then it slows down for depths higher than 300 µm. While several techniques have been proposed to establish faster drilling, they mainly rely on tuning the machining parameters to enhance the machining performance. However, with this approach machining parameters need to be constantly tuned to achieve certain machining performance depending on the size of the tool and the features needed. Therefore, this necessitates further work to enhance understanding regarding the SACE machining process fundamentals in order to enhance machining speed and quality. Since SACE is a thermal assisted etching process, both local heating and flushing of electrolyte in the machining zone are required. However, to the authors’ knowledge there is not any study that attempts to analyze the effect of each of these machining limiting factors on the machining performance. This work attempts to clarify the effect of each flushing and heating on the drilling progress for hole depths higher than 100 microns. It therefore provides a deeper understanding of the fundamentals of the SACE machining process.

Experimental Optimization of Process Parameters in CuNi18Zn20 Micromachining

Ultraprecision micromachining is a technology suitable to fabricate miniaturized and complicated 3-dimensional microstructures and micromechanisms. High geometrical precision and elevated surface finishing are both key requirements in several manufacturing sectors. Electronics, biomedicals, optics and watchmaking industries are some of the fields where micromachining finds applications. In the last years, the integration between product functions, the miniaturization of the features and the increasing of geometrical complexity are trends which are shared by all the cited industrial sectors. These tendencies implicate higher requirements and stricter geometrical and dimensional tolerances in machining. From this perspective, the optimization of the micromachining process parameters assumes a crucial role in order to increase the efficiency and effectiveness of the process. An interesting example is offered by the high-end horology field. The optimization of micro machining is indispensable to achieve excellent surface finishing combined with high precision. The cost-saving objective can be pursued by limiting manual post-finishing and by complying the very strict quality standards directly in micromachining. A micro-machining optimization technique is presented in this a paper. The procedure was applied to manufacturing of main-plates and bridges of a wristwatch movement. Cutting speed, feed rate and depth of cut were varied in an experimental factorial plan in order to investigate their correlation with some fundamental properties of the machined features. The dimensions, the geometry and the surface finishing of holes, pins and pockets were evaluated as results of the micromachining optimization. The identified correlations allow to manufacture a wristwatch movement in conformity with the required technical characteristics and by considering the cost and time constraints.

Micro-machining: An overview (Part II)

This article on ‘Micro-machining: An Overview (Part II)’ is in continuation to ‘Micro-machining: An Overview (Part I)’ published in this journal ( Journal of Micromanufacturing). It consists of four parts, namely, electrochemical micro-texturing, electrochemical spark micro-machining, molecular dynamics simulation and sustainability issues of micro-machining processes. Electrochemical micro-texturing (ECMTex) deals with various techniques developed for micro-texturing on different types of workpiece-surfaces, namely, flat, curved and free-form surfaces. Here, basically two categories of techniques have been reviewed, namely, with mask and without mask. It also deals with ‘single point tool micro-texturing’ which turns out to be a single-step technique requiring minimum time, but the accuracy and repeatability obtained after micro-texturing need to be critically analysed. For mass production, one needs to go for sinking kind of ECMTex processes. Electrochemical spark micro-machining (ECSMM) is an interesting hybrid (ECM+EDM) process which can be applied for electrically conducting as well as electrically non-conducting materials. However, the work reported in this article deals only with the electrically non-conducting materials for which this process was initially developed. This process has a lot of potential for theoretical work to be done. In this article, two theories of sparking/discharging have been briefly mentioned: single bubble discharging/sparking and single surface discharging. It also dicusses its applications for different types of electrically non-conducting materials. Molecular dynamics simulation (MDS) of micro-/nano-machining processes is very important, but it is very cumbersome to understand at atomic/molecular scale. In these processes, the material behaviour at micro-/nano-level machining is completely different as compared to bulk-machining (macro-machining) processes. Hence, some fundamentals of MDS have been discussed. It just gives the idea of available techniques, softwares and models for different types of processes. However, there is the need of further research work to be done for clearly understanding the MDS of micro-/nano-machining. In the end, the sustainability of micro-machining issues have been discussed, mainly based on the energy consumption per unit mass of production. It is concluded that the advanced micro-manufacturing processes are highly energy-intensive processes, and they need further studies to be done for making them more suitable from sustainability point of view. At the end of each section, some potential areas of research for enhancing the accuracy and repeatability, and minimising the production time of each process have been discussed.