Comparative Evaluation of the Marginal Adaptation of Cast Ni-Cr Copings, Direct Metal Laser Sintering Co-Cr Copings, and Computer-aided Design and Computer-aided Manufacturing Zr Copings: An In-vitro Study

Aim: To compare the marginal adaptation of crowns fabricated by using three different resin-ceramic computer-aided design/computer-aided manufacturing (CAD/CAM) materials. Materials and Methods: Crowns fabricated from three different resin-ceramic CAD/CAM blocks, applied on a typodont premolar (#14), were tested with regard to marginal adaptation, in this in vitro study. The typodont maxillary first premolar was prepared to serve as the master die and digitized with an intraoral scanner. The same virtual crown design was used to fabricate all specimens. Forty-eight crowns were fabricated from the same virtual crown design using three different CAD/CAM resin-ceramic blocks as follows ( n = 16): Lava Ultimate (LU), GC Cerasmart (GC), Vita Enamic (VE). Master die and crowns were scanned with a laboratory scanner and three-dimensional data were transferred into three-matic software. The software calculated the mean of the marginal discrepancy (MD) for each crown in negative and positive values, representing under and over estimation of the crown margin, respectively. A marginal discrepancy index (MDI) was obtained for each group using negative and positive MDs. All data were statistically analyzed using one-way analysis of variance and Tukey’s honest significance test ( α = 0.05). Results: The analysis of variance showed no statistical differences between materials regarding the negative and positive MDs ( P > .05). The MDI for LU was lower than GC and VE ( P < .05). Conclusion: The marginal adaptation of different resin-ceramic materials was different with regard to MDI values. Nevertheless, the MD values of all groups were within the clinically acceptable range.

Download Full-text

Efeito da fumaça de cigarro e escovação simulada na cêramica vítrea de dissilicato de lítio CAD/CAM

Revista Eletrônica Acervo Saúde ◽

10.25248/reas.e7296.2021 ◽

2021 ◽

Vol 13 (4) ◽

pp. e7296

Author(s):

Magna Andréa Rabêlo Diógenes ◽

Francisca Tauliane Lemos de Castro ◽

Samara Kelly da Silva Cavalcante ◽

Ana Carolina Matias Dinelly Pinto ◽

Pedro Henrique Chaves Isaias ◽

...

Keyword(s):

Computer Aided Design ◽

Lithium Disilicate ◽

Computer Aided Manufacturing ◽

Computer Aided ◽

Cad Cam ◽

Aided Design

Objetivo: Revisar acerca do efeito da fumaça do cigarro, associada ou não à escovação, na rugosidade superficial e na microdureza de uma cerâmica vítrea de dissilicato de lítio “Computer-Aided Design/Computer-Aided Manufacturing” (CAD/CAM). Métodos: Pesquisaram-se os descritores cadastrados no MeSH “lithium disilicate”, “smoking”, “CAD CAM”, “brushing”, “rough”, “hardness”, combinados entre si pelo operador booleano “AND”, na base de dados PubMed nos últimos 5 anos. Resultados: De acordo com a pesquisa, foram encontrados 625 artigos e selecionados 12 estudos in vitro. 5 estudos concluíram que as restaurações cerâmicas CAD/CAM apresentaram estabilidade de cor e de rugosidade da superfície, após escovação simulada e termociclagem. 4 estudos observaram que a escovação simulada e algumas bebidas aumentaram significativamente a rugosidade superficial da cerâmica de dissilicato de lítio. 3 estudos inferiram que a rugosidade superficial e a microdureza podem ser influenciadas pelos tratamentos de superfícies. Considerações finais: As cerâmicas de dissilicato de lítio CAD/CAM possuem propriedades satisfatórias em relação a sua resistência e estética, após exposição à fumaça do cigarro, associada ou não com a escovação.

Download Full-text