Simulation of Deformation Process Failure of Jointed Rock Masses Based on the Numerical Manifold Method

On the basis of the numerical manifold method, this work introduces the concept of stress intensity factor at the crack tip in fracture mechanics and proposes the utilisation of artificial joint technology to ensure the accuracy of joint geometric dimensions in the element generation of the numerical manifold method. The contour integral method is used to solve the stress intensity factor at the joint tip, and the failure criterion and direction of crack propagation at the joint tip are determined. Element reconstruction and crack tracking are implemented in crack propagation, and a simulation programme of the entire process of deformation, failure, propagation and coalescence of jointed rock masses is developed. The rationality of the proposed method is verified by performing the typical uniaxial compression test and direct shear test.

Numerical Modeling on Dynamic Characteristics of Jointed Rock Masses Subjected to Repetitive Impact Loading

A discrete element method code was used to investigate the damage characteristics of jointed rock masses under repetitive impact loading. The Flat-Joint Contact Model (FJCM) in the two-dimensional particle flow code (PFC2D) was used to calibrate the microparameters that control the macroscopic behavior of the rock. The relationship between macro- and microparameters by a series of uniaxial direct tension and compression numerical tests based on an orthogonal experimental design method was obtained to calibrate the microparameters accurately. Then, the Synthetic Rock Mass (SRM) method that incorporates joints into the calibrated particle model was used to construct large-scale jointed rock mass specimens, and the repetitive drop hammer impact numerical tests on SRM specimens with different numbers of horizontal joints and dip angle joints were carried out to study the damage evolution, stress wave propagation, and energy dissipation characteristics. The results show that the greater the number of joints, the greater the number of cracks generated, the greater the degree of damage, and the more energy dissipated for rock masses with horizontal joints. The greater the dip angle of joints, the less the number of cracks generated, the less the degree of damage, and the less energy dissipated for rock masses with different dip angles of joints. The impact-induced stress waves will be reflected when they encounter preexisting joints in the process of propagation. When the reflected stress waves meet with subsequent stress waves, the stress waves will change from compressional waves to tensile waves, producing tensile damage inside rock masses.

Determination of representative elementary volume (REV) for jointed rock masses exhibiting scale-dependent behavior: a numerical investigation

Representative elementary volume (REV) is defined as the usual size of a rock mass structure beyond which its mechanical properties are homogenous and isotropic, and its behavior can be modeled using the equivalent continuum approach. Determination of REV is a complex problem in rock engineering due to its definition ambiguity and application area. This study is one of the first attempts to define a REV for jointed rock masses using the equivalent continuum approach. It is aimed to numerically search a ratio between the characteristic size of an engineering structure and pre-existing joint spacing, which are the two most important contributing elements in assessing REV. For this purpose, four hypothetical engineering cases were investigated using the RS2 (Phase2 v. 9.0) finite element (FE) analysis program. An underground circular opening with a constant diameter, an open-pit mine with varying bench heights, a single bench with a constant height, and an underground powerhouse cavern with a known dimension were executed for possible changes in the safety factor and total displacement measurements under several joint spacing values. Different cut-off REVs were calculated for FE models depending on the type of excavation and measurement method. An average REV size of 19.0, ranging between a minimum of 2 for tunnels and a maximum of 48 for slopes, was found in numerical analysis. The calculated sizes of REV were significantly larger than the range of values (5 to 10) commonly reported in the relevant geotechnical literature.

Determination of representative elementary volume (REV) for jointed rock masses exhibiting scale-dependent behavior: A numerical investigation

Representative elementary volume (REV) is defined as the usual size of a rock mass structure beyond which its mechanical properties are homogenous and isotropic, and its behavior can be modeled using the equivalent continuum approach. Determination of REV is a complex problem in rock engineering due to its definition ambiguity and application area. This study is one of the first attempts to define a REV for jointed rock masses using the equivalent continuum approach. It is aimed to numerically search a ratio between the characteristic size of an engineering structure and pre-existing joint spacing, which are the two most important contributing elements in assessing REV. For this purpose, four hypothetical engineering cases were investigated using the RS2 (Phase2 v. 9.0) finite element (FE) analysis program. An underground circular opening with a constant diameter, an open-pit mine with varying bench heights, a single bench with a constant height, and an underground powerhouse cavern with a known dimension were executed for possible changes in the safety factor and total displacement measurements under several joint spacing values. Different cut-off REVs were calculated for FE models depending on the type of excavation and measurement method. An average REV size of 19.0, ranging between a minimum of 2 for tunnels and a maximum of 48 for slopes, was found in numerical analysis. The calculated sizes of REV were significantly larger than the range of values (5 to 10) commonly reported in the relevant geotechnical literature.

Experimental Study on Influence of Joint Surface Morphology on Strength and Deformation of Nonthrough Jointed Rock Masses under Direct Shear

Direct shear tests were carried out on nonthrough jointed rock masses (NTJRM) with three types of joints under five normal stresses. The strength characteristics of shear strength, initial crack strength, and residual strength and the deformation characteristics of tangential displacement and dilatancy displacement as well as the transformation of failure mode and the variation of shear parameters of rock mass with different joint morphology are studied. Under the same normal stress, with the increase of joint undulation, the shear strength of NTJRM increases, and the corresponding tangential displacement of NTJRM increases. Two typical failure modes are observed: TTTS mode and TSSS mode. TTTS model indicates that the initial failure, extension failure, and final failure of rock mass are caused by tensile action, while the failure mode of through plane is formed by shear action. The initial failure of TSSS mode rock mass is caused by tensile action, while the expansion and final failure are caused by shear action, and the failure mode of through plane is formed under shear action. When the joint undulation is small and the normal stress is small, NTJRM will fail in TTTS mode; when the joint undulation is large and the normal stress is large, NTJRM will fail in TSSS mode. The results show that the shear parameters of NTJRM are related to the joint morphology, the bond force increases with the increase of joint undulation, and the internal friction angle increases with the increase of joint undulation. The research results of direct shear test of nonthrough jointed rock mass can provide reference for related research.